203 lines
6.8 KiB
C++
203 lines
6.8 KiB
C++
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
|
|
// NOTE - the HAL version of the rrd device uses a generic ST7920 device. See the
|
|
// file u8g_dev_st7920_128x64_HAL.cpp for the HAL version.
|
|
|
|
#include "../../inc/MarlinConfig.h"
|
|
|
|
#if ENABLED(U8GLIB_ST7920)
|
|
|
|
#if !(defined(U8G_HAL_LINKS) || defined(__SAM3X8E__))
|
|
|
|
#include "../../HAL/shared/Delay.h"
|
|
|
|
#define ST7920_CLK_PIN LCD_PINS_D4
|
|
#define ST7920_DAT_PIN LCD_PINS_ENABLE
|
|
#define ST7920_CS_PIN LCD_PINS_RS
|
|
|
|
//#define PAGE_HEIGHT 8 //128 byte framebuffer
|
|
#define PAGE_HEIGHT 16 //256 byte framebuffer
|
|
//#define PAGE_HEIGHT 32 //512 byte framebuffer
|
|
|
|
#define LCD_PIXEL_WIDTH 128
|
|
#define LCD_PIXEL_HEIGHT 64
|
|
|
|
#include <U8glib.h>
|
|
|
|
//set optimization so ARDUINO optimizes this file
|
|
#pragma GCC optimize (3)
|
|
|
|
// If you want you can define your own set of delays in Configuration.h
|
|
//#define ST7920_DELAY_1 DELAY_NS(0)
|
|
//#define ST7920_DELAY_2 DELAY_NS(0)
|
|
//#define ST7920_DELAY_3 DELAY_NS(0)
|
|
|
|
#if F_CPU >= 20000000
|
|
#define CPU_ST7920_DELAY_1 DELAY_NS(0)
|
|
#define CPU_ST7920_DELAY_2 DELAY_NS(0)
|
|
#define CPU_ST7920_DELAY_3 DELAY_NS(50)
|
|
#elif MB(3DRAG) || MB(K8200) || MB(K8400) || MB(SILVER_GATE)
|
|
#define CPU_ST7920_DELAY_1 DELAY_NS(0)
|
|
#define CPU_ST7920_DELAY_2 DELAY_NS(188)
|
|
#define CPU_ST7920_DELAY_3 DELAY_NS(0)
|
|
#elif MB(MINIRAMBO) || MB(EINSY_RAMBO)
|
|
#define CPU_ST7920_DELAY_1 DELAY_NS(0)
|
|
#define CPU_ST7920_DELAY_2 DELAY_NS(250)
|
|
#define CPU_ST7920_DELAY_3 DELAY_NS(0)
|
|
#elif MB(RAMBO)
|
|
#define CPU_ST7920_DELAY_1 DELAY_NS(0)
|
|
#define CPU_ST7920_DELAY_2 DELAY_NS(0)
|
|
#define CPU_ST7920_DELAY_3 DELAY_NS(0)
|
|
#elif MB(BQ_ZUM_MEGA_3D)
|
|
#define CPU_ST7920_DELAY_1 DELAY_NS(0)
|
|
#define CPU_ST7920_DELAY_2 DELAY_NS(0)
|
|
#define CPU_ST7920_DELAY_3 DELAY_NS(189)
|
|
#elif F_CPU == 16000000
|
|
#define CPU_ST7920_DELAY_1 DELAY_NS(0)
|
|
#define CPU_ST7920_DELAY_2 DELAY_NS(0)
|
|
#define CPU_ST7920_DELAY_3 DELAY_NS(63)
|
|
#else
|
|
#error "No valid condition for delays in 'ultralcd_st7920_u8glib_rrd.h'"
|
|
#endif
|
|
|
|
#ifndef ST7920_DELAY_1
|
|
#define ST7920_DELAY_1 CPU_ST7920_DELAY_1
|
|
#endif
|
|
#ifndef ST7920_DELAY_2
|
|
#define ST7920_DELAY_2 CPU_ST7920_DELAY_2
|
|
#endif
|
|
#ifndef ST7920_DELAY_3
|
|
#define ST7920_DELAY_3 CPU_ST7920_DELAY_3
|
|
#endif
|
|
|
|
#define ST7920_SND_BIT \
|
|
WRITE(ST7920_CLK_PIN, LOW); ST7920_DELAY_1; \
|
|
WRITE(ST7920_DAT_PIN, val & 0x80); ST7920_DELAY_2; \
|
|
WRITE(ST7920_CLK_PIN, HIGH); ST7920_DELAY_3; \
|
|
val <<= 1
|
|
|
|
static void ST7920_SWSPI_SND_8BIT(uint8_t val) {
|
|
ST7920_SND_BIT; // 1
|
|
ST7920_SND_BIT; // 2
|
|
ST7920_SND_BIT; // 3
|
|
ST7920_SND_BIT; // 4
|
|
ST7920_SND_BIT; // 5
|
|
ST7920_SND_BIT; // 6
|
|
ST7920_SND_BIT; // 7
|
|
ST7920_SND_BIT; // 8
|
|
}
|
|
|
|
#if DOGM_SPI_DELAY_US > 0
|
|
#define U8G_DELAY() DELAY_US(DOGM_SPI_DELAY_US)
|
|
#else
|
|
#define U8G_DELAY() DELAY_US(10)
|
|
#endif
|
|
|
|
#define ST7920_CS() { WRITE(ST7920_CS_PIN,1); U8G_DELAY(); }
|
|
#define ST7920_NCS() { WRITE(ST7920_CS_PIN,0); }
|
|
#define ST7920_SET_CMD() { ST7920_SWSPI_SND_8BIT(0xF8); U8G_DELAY(); }
|
|
#define ST7920_SET_DAT() { ST7920_SWSPI_SND_8BIT(0xFA); U8G_DELAY(); }
|
|
#define ST7920_WRITE_BYTE(a) { ST7920_SWSPI_SND_8BIT((uint8_t)((a)&0xF0u)); ST7920_SWSPI_SND_8BIT((uint8_t)((a)<<4u)); U8G_DELAY(); }
|
|
#define ST7920_WRITE_BYTES(p,l) { for (uint8_t i = l + 1; --i;) { ST7920_SWSPI_SND_8BIT(*p&0xF0); ST7920_SWSPI_SND_8BIT(*p<<4); p++; } U8G_DELAY(); }
|
|
|
|
uint8_t u8g_dev_rrd_st7920_128x64_fn(u8g_t *u8g, u8g_dev_t *dev, uint8_t msg, void *arg) {
|
|
uint8_t i, y;
|
|
switch (msg) {
|
|
case U8G_DEV_MSG_INIT: {
|
|
OUT_WRITE(ST7920_CS_PIN, LOW);
|
|
OUT_WRITE(ST7920_DAT_PIN, LOW);
|
|
OUT_WRITE(ST7920_CLK_PIN, HIGH);
|
|
|
|
ST7920_CS();
|
|
u8g_Delay(120); //initial delay for boot up
|
|
ST7920_SET_CMD();
|
|
ST7920_WRITE_BYTE(0x20); //non-extended mode
|
|
ST7920_WRITE_BYTE(0x08); //display off, cursor+blink off
|
|
ST7920_WRITE_BYTE(0x01); //clear DDRAM ram
|
|
u8g_Delay(15); //delay for DDRAM clear
|
|
ST7920_WRITE_BYTE(0x24); //extended mode
|
|
ST7920_WRITE_BYTE(0x26); //extended mode + GDRAM active
|
|
for (y = 0; y < (LCD_PIXEL_HEIGHT) / 2; y++) { //clear GDRAM
|
|
ST7920_WRITE_BYTE(0x80 | y); //set y
|
|
ST7920_WRITE_BYTE(0x80); //set x = 0
|
|
ST7920_SET_DAT();
|
|
for (i = 0; i < 2 * (LCD_PIXEL_WIDTH) / 8; i++) //2x width clears both segments
|
|
ST7920_WRITE_BYTE(0);
|
|
ST7920_SET_CMD();
|
|
}
|
|
ST7920_WRITE_BYTE(0x0C); //display on, cursor+blink off
|
|
ST7920_NCS();
|
|
}
|
|
break;
|
|
|
|
case U8G_DEV_MSG_STOP: break;
|
|
|
|
case U8G_DEV_MSG_PAGE_NEXT: {
|
|
uint8_t* ptr;
|
|
u8g_pb_t* pb = (u8g_pb_t*)(dev->dev_mem);
|
|
y = pb->p.page_y0;
|
|
ptr = (uint8_t*)pb->buf;
|
|
|
|
ST7920_CS();
|
|
for (i = 0; i < PAGE_HEIGHT; i ++) {
|
|
ST7920_SET_CMD();
|
|
if (y < 32) {
|
|
ST7920_WRITE_BYTE(0x80 | y); //y
|
|
ST7920_WRITE_BYTE(0x80); //x=0
|
|
}
|
|
else {
|
|
ST7920_WRITE_BYTE(0x80 | (y - 32)); //y
|
|
ST7920_WRITE_BYTE(0x80 | 8); //x=64
|
|
}
|
|
ST7920_SET_DAT();
|
|
ST7920_WRITE_BYTES(ptr, (LCD_PIXEL_WIDTH) / 8); //ptr is incremented inside of macro
|
|
y++;
|
|
}
|
|
ST7920_NCS();
|
|
}
|
|
break;
|
|
}
|
|
#if PAGE_HEIGHT == 8
|
|
return u8g_dev_pb8h1_base_fn(u8g, dev, msg, arg);
|
|
#elif PAGE_HEIGHT == 16
|
|
return u8g_dev_pb16h1_base_fn(u8g, dev, msg, arg);
|
|
#else
|
|
return u8g_dev_pb32h1_base_fn(u8g, dev, msg, arg);
|
|
#endif
|
|
}
|
|
|
|
uint8_t u8g_dev_st7920_128x64_rrd_buf[(LCD_PIXEL_WIDTH) * (PAGE_HEIGHT) / 8] U8G_NOCOMMON;
|
|
u8g_pb_t u8g_dev_st7920_128x64_rrd_pb = {{PAGE_HEIGHT, LCD_PIXEL_HEIGHT, 0, 0, 0}, LCD_PIXEL_WIDTH, u8g_dev_st7920_128x64_rrd_buf};
|
|
u8g_dev_t u8g_dev_st7920_128x64_rrd_sw_spi = {u8g_dev_rrd_st7920_128x64_fn, &u8g_dev_st7920_128x64_rrd_pb, &u8g_com_null_fn};
|
|
|
|
#if ENABLED(LIGHTWEIGHT_UI)
|
|
// We have to include the code for the lightweight UI here
|
|
// as it relies on macros that are only defined in this file.
|
|
#include "status_screen_lite_ST7920_spi.h"
|
|
#endif
|
|
|
|
#pragma GCC reset_options
|
|
|
|
#endif // U8G_HAL_LINKS
|
|
|
|
#endif // U8GLIB_ST7920
|