This repository has been archived on 2022-01-28. You can view files and clone it, but cannot push or open issues or pull requests.
Marlin-Artillery-M600/Marlin/pins_TEENSY2.h
Scott Lahteine c0d7ea3e7e Overridable Options - Part 4 (PR#2556)
Apply `ENABLED` / `DISABLED` / `HAS_SERVOS` macros to pins files.
2015-07-31 00:44:53 -05:00

113 lines
4.3 KiB
C

/**
* Teensy++ 2.0 Breadboard pin assignments (AT90USB1286)
* Requires the Teensyduino software with Teensy++ 2.0 selected in Arduino IDE!
* http://www.pjrc.com/teensy/teensyduino.html
* See http://reprap.org/wiki/Printrboard for more info
*
* CLI build: DEFINES=AT90USBxx_TEENSYPP_ASSIGNMENTS HARDWARE_MOTHERBOARD=84 make
*
* DaveX plan for Teensylu/printrboard-type pinouts for a TeensyBreadboard:
* (ref teensylu & sprinter)
*
* USB
* GND GND |-----#####-----| +5V ATX +5SB
* ATX PS_ON PWM 27 |b7 ##### b6| 26 PWM* Stepper Enable
* PWM 0 |d0 b5| 25 PWM*
* PWM 1 |d1 b4| 24 PWM
* X_MIN 2 |d2 b3| 23 MISO_PIN
* Y_MIN 3 |d3 b2| 22 MOSI_PIN
* Z_MIN 4 |d4 * * b1| 21 SCK_PIN
* 5 |d5 e e b0| 20 SDSS
* LED 6 |d6 5 4 e7| 19
* 7 |d7 e6| 18
* LCD RS 8 |e0 | GND
* LCD EN 9 |e1 a4 a0 R| AREF
* LCD D4 10 |c0 a5 a1 f0| 38 A0 ENC_1
* LCD D5 11 |c1 a6 a2 f1| 39 A1 ENC_2
* LCD D6 12 |c2 a7 a3 f2| 40 A2 ENC_CLK
* LCD D6 13 |c3 f3| 41 A3
* Bed Heat PWM 14 |c4 V G R f4| 42 A4
* Extruder Heat PWM 15 |c5 c n S f5| 43 A5
* Fan PWM 16 |c6 c d T f6| 44 A6 Bed TC
* 17 |c7 * * * f7| 45 A7 Extruder TC * 4.7k * +5
* -----------------
*
* Interior E4: 36, INT4
* Interior E5: 37, INT5
* Interior PA0-7: 28-35 -- Printrboard and Teensylu use these pins for step & direction:
* T++ PA Signal Marlin
*
* Z STEP 32 a4 a0 28 X STEP
* Z DIR 33 a5 a1 29 X DIR
* E STEP 34 a6 a2 30 Y STEP
* E DIR 35 a7 a3 31 Y DIR
*/
#ifndef __AVR_AT90USB1286__
#error Oops! Make sure you have 'Teensy++ 2.0' selected from the 'Tools -> Boards' menu.
#endif
#ifndef AT90USBxx_TEENSYPP_ASSIGNMENTS // use Teensyduino Teensy++2.0 pin assignments instead of Marlin alphabetical.
#error Uncomment #define AT90USBxx_TEENSYPP_ASSIGNMENTS in fastio.h for this config
// (or build from command line)
#endif
#define LARGE_FLASH true
#define X_STEP_PIN 28 // 0 Marlin
#define X_DIR_PIN 29 // 1 Marlin
#define X_ENABLE_PIN 26
#define Y_STEP_PIN 30 // 2 Marlin
#define Y_DIR_PIN 31 // 3
#define Y_ENABLE_PIN 26 // Shared w/x
#define Z_STEP_PIN 32 // 4
#define Z_DIR_PIN 33 // 5
#define Z_ENABLE_PIN 26 // Shared w/x
#define E0_STEP_PIN 34 // 6
#define E0_DIR_PIN 35 // 7
#define E0_ENABLE_PIN 26 // Shared w/x
#define HEATER_0_PIN 15 // 21 // Extruder
#define HEATER_1_PIN -1
#define HEATER_2_PIN -1
#define HEATER_BED_PIN 14 // 20 // Bed
#define FAN_PIN 16 // 22 // Fan
#define X_STOP_PIN 2
#define Y_STOP_PIN 3
#define Z_STOP_PIN 4
#define TEMP_0_PIN 7 // Extruder / Analog pin numbering
#define TEMP_BED_PIN 6 // Bed / Analog pin numbering
#define TEMP_1_PIN -1
#define TEMP_2_PIN -1
#define SDPOWER -1
#define SDCARDDETECT -1
#define SDSS 20 // 8
#define LED_PIN 6
#define PS_ON_PIN 27
#define KILL_PIN -1
#define ALARM_PIN -1
#if DISABLED(SDSUPPORT)
// these pins are defined in the SD library if building with SD support
#define SCK_PIN 21 // 9
#define MISO_PIN 23 // 11
#define MOSI_PIN 22 // 10
#endif
#if ENABLED(ULTIPANEL)
#define LCD_PINS_RS 8
#define LCD_PINS_ENABLE 9
#define LCD_PINS_D4 10
#define LCD_PINS_D5 11
#define LCD_PINS_D6 12
#define LCD_PINS_D7 13
#define BTN_EN1 38
#define BTN_EN2 39
#define BTN_ENC 40
#endif