#defining something just to define something else doesn’t make sense If you want SDCARDDETECTINVERTED, just define it yourself. If the previous code was intended to define, undefined and then again define the term, that code is improper.
512 lines
16 KiB
C
512 lines
16 KiB
C
/**
|
||
* Conditionals.h
|
||
* Defines that depend on configuration but are not editable.
|
||
*/
|
||
#ifndef CONDITIONALS_H
|
||
|
||
#ifndef M_PI
|
||
#define M_PI 3.1415926536
|
||
#endif
|
||
|
||
#ifndef CONFIGURATION_LCD // Get the LCD defines which are needed first
|
||
|
||
#define PIN_EXISTS(PN) (defined(PN##_PIN) && PN##_PIN >= 0)
|
||
|
||
#define CONFIGURATION_LCD
|
||
|
||
#if defined(MAKRPANEL)
|
||
#define DOGLCD
|
||
#define SDSUPPORT
|
||
#define DEFAULT_LCD_CONTRAST 17
|
||
#define ULTIPANEL
|
||
#define NEWPANEL
|
||
#endif
|
||
|
||
#if defined(miniVIKI) || defined(VIKI2) || defined(ELB_FULL_GRAPHIC_CONTROLLER)
|
||
#define ULTRA_LCD //general LCD support, also 16x2
|
||
#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
|
||
#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
|
||
|
||
#ifdef miniVIKI
|
||
#define DEFAULT_LCD_CONTRAST 95
|
||
#elif defined(VIKI2)
|
||
#define DEFAULT_LCD_CONTRAST 40
|
||
#elif defined(ELB_FULL_GRAPHIC_CONTROLLER)
|
||
#define DEFAULT_LCD_CONTRAST 110
|
||
#define U8GLIB_LM6059_AF
|
||
#endif
|
||
|
||
#define ENCODER_PULSES_PER_STEP 4
|
||
#define ENCODER_STEPS_PER_MENU_ITEM 1
|
||
#endif
|
||
|
||
// Generic support for SSD1306 OLED based LCDs.
|
||
#if defined(U8GLIB_SSD1306)
|
||
#define ULTRA_LCD //general LCD support, also 16x2
|
||
#define DOGLCD // Support for I2C LCD 128x64 (Controller SSD1306 graphic Display Family)
|
||
#endif
|
||
|
||
|
||
#ifdef PANEL_ONE
|
||
#define SDSUPPORT
|
||
#define ULTIMAKERCONTROLLER
|
||
#endif
|
||
|
||
#ifdef REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||
#define DOGLCD
|
||
#define U8GLIB_ST7920
|
||
#define REPRAP_DISCOUNT_SMART_CONTROLLER
|
||
#endif
|
||
|
||
#if defined(ULTIMAKERCONTROLLER) || defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL)
|
||
#define ULTIPANEL
|
||
#define NEWPANEL
|
||
#endif
|
||
|
||
#ifdef REPRAPWORLD_KEYPAD
|
||
#define ULTIPANEL
|
||
#define NEWPANEL
|
||
#endif
|
||
|
||
#ifdef RA_CONTROL_PANEL
|
||
#define LCD_I2C_TYPE_PCA8574
|
||
#define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander
|
||
#define ULTIPANEL
|
||
#define NEWPANEL
|
||
#endif
|
||
|
||
/**
|
||
* I2C PANELS
|
||
*/
|
||
|
||
#ifdef LCD_I2C_SAINSMART_YWROBOT
|
||
// This uses the LiquidCrystal_I2C library ( https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home )
|
||
// Make sure it is placed in the Arduino libraries directory.
|
||
#define LCD_I2C_TYPE_PCF8575
|
||
#define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander
|
||
#define ULTIPANEL
|
||
#define NEWPANEL
|
||
#endif
|
||
|
||
// PANELOLU2 LCD with status LEDs, separate encoder and click inputs
|
||
#ifdef LCD_I2C_PANELOLU2
|
||
// This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 )
|
||
// Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.
|
||
// (v1.2.3 no longer requires you to define PANELOLU in the LiquidTWI2.h library header file)
|
||
// Note: The PANELOLU2 encoder click input can either be directly connected to a pin
|
||
// (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
|
||
#define LCD_I2C_TYPE_MCP23017
|
||
#define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
|
||
#define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD
|
||
|
||
#ifndef ENCODER_PULSES_PER_STEP
|
||
#define ENCODER_PULSES_PER_STEP 4
|
||
#endif
|
||
|
||
#ifndef ENCODER_STEPS_PER_MENU_ITEM
|
||
#define ENCODER_STEPS_PER_MENU_ITEM 1
|
||
#endif
|
||
|
||
#ifdef LCD_USE_I2C_BUZZER
|
||
#define LCD_FEEDBACK_FREQUENCY_HZ 1000
|
||
#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
|
||
#endif
|
||
|
||
#define ULTIPANEL
|
||
#define NEWPANEL
|
||
#endif
|
||
|
||
// Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
|
||
#ifdef LCD_I2C_VIKI
|
||
// This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 )
|
||
// Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.
|
||
// Note: The pause/stop/resume LCD button pin should be connected to the Arduino
|
||
// BTN_ENC pin (or set BTN_ENC to -1 if not used)
|
||
#define LCD_I2C_TYPE_MCP23017
|
||
#define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
|
||
#define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD (requires LiquidTWI2 v1.2.3 or later)
|
||
#define ULTIPANEL
|
||
#define NEWPANEL
|
||
#endif
|
||
|
||
// Shift register panels
|
||
// ---------------------
|
||
// 2 wire Non-latching LCD SR from:
|
||
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
|
||
|
||
#ifdef SAV_3DLCD
|
||
#define SR_LCD_2W_NL // Non latching 2 wire shiftregister
|
||
#define ULTIPANEL
|
||
#define NEWPANEL
|
||
#endif
|
||
|
||
#ifdef ULTIPANEL
|
||
#define NEWPANEL //enable this if you have a click-encoder panel
|
||
#define SDSUPPORT
|
||
#define ULTRA_LCD
|
||
#ifdef DOGLCD // Change number of lines to match the DOG graphic display
|
||
#define LCD_WIDTH 22
|
||
#define LCD_HEIGHT 5
|
||
#else
|
||
#define LCD_WIDTH 20
|
||
#define LCD_HEIGHT 4
|
||
#endif
|
||
#else //no panel but just LCD
|
||
#ifdef ULTRA_LCD
|
||
#ifdef DOGLCD // Change number of lines to match the 128x64 graphics display
|
||
#define LCD_WIDTH 22
|
||
#define LCD_HEIGHT 5
|
||
#else
|
||
#define LCD_WIDTH 16
|
||
#define LCD_HEIGHT 2
|
||
#endif
|
||
#endif
|
||
#endif
|
||
|
||
#ifdef DOGLCD
|
||
/* Custom characters defined in font font_6x10_marlin_symbols */
|
||
// \x00 intentionally skipped to avoid problems in strings
|
||
#define LCD_STR_REFRESH "\x01"
|
||
#define LCD_STR_FOLDER "\x02"
|
||
#define LCD_STR_ARROW_RIGHT "\x03"
|
||
#define LCD_STR_UPLEVEL "\x04"
|
||
#define LCD_STR_CLOCK "\x05"
|
||
#define LCD_STR_FEEDRATE "\x06"
|
||
#define LCD_STR_BEDTEMP "\x07"
|
||
#define LCD_STR_THERMOMETER "\x08"
|
||
#define LCD_STR_DEGREE "\x09"
|
||
|
||
#define LCD_STR_SPECIAL_MAX '\x09'
|
||
// Maximum here is 0x1f because 0x20 is ' ' (space) and the normal charsets begin.
|
||
// Better stay below 0x10 because DISPLAY_CHARSET_HD44780_WESTERN begins here.
|
||
#else
|
||
/* Custom characters defined in the first 8 characters of the LCD */
|
||
#define LCD_STR_BEDTEMP "\x00" // this will have 'unexpected' results when used in a string!
|
||
#define LCD_STR_DEGREE "\x01"
|
||
#define LCD_STR_THERMOMETER "\x02"
|
||
#define LCD_STR_UPLEVEL "\x03"
|
||
#define LCD_STR_REFRESH "\x04"
|
||
#define LCD_STR_FOLDER "\x05"
|
||
#define LCD_STR_FEEDRATE "\x06"
|
||
#define LCD_STR_CLOCK "\x07"
|
||
#define LCD_STR_ARROW_RIGHT ">" /* from the default character set */
|
||
#endif
|
||
|
||
/**
|
||
* Default LCD contrast for dogm-like LCD displays
|
||
*/
|
||
#if defined(DOGLCD) && !defined(DEFAULT_LCD_CONTRAST)
|
||
#define DEFAULT_LCD_CONTRAST 32
|
||
#endif
|
||
|
||
#ifdef DOGLCD
|
||
#define HAS_LCD_CONTRAST
|
||
#ifdef U8GLIB_ST7920
|
||
#undef HAS_LCD_CONTRAST
|
||
#endif
|
||
#ifdef U8GLIB_SSD1306
|
||
#undef HAS_LCD_CONTRAST
|
||
#endif
|
||
#endif
|
||
|
||
#else // CONFIGURATION_LCD
|
||
|
||
#define CONDITIONALS_H
|
||
|
||
#include "pins.h"
|
||
|
||
#ifndef AT90USB
|
||
#define HardwareSerial_h // trick to disable the standard HWserial
|
||
#endif
|
||
|
||
#if (ARDUINO >= 100)
|
||
#include "Arduino.h"
|
||
#else
|
||
#include "WProgram.h"
|
||
#endif
|
||
|
||
/**
|
||
* ENDSTOPPULLUPS
|
||
*/
|
||
#ifdef ENDSTOPPULLUPS
|
||
#ifndef DISABLE_MAX_ENDSTOPS
|
||
#define ENDSTOPPULLUP_XMAX
|
||
#define ENDSTOPPULLUP_YMAX
|
||
#define ENDSTOPPULLUP_ZMAX
|
||
#endif
|
||
#ifndef DISABLE_MIN_ENDSTOPS
|
||
#define ENDSTOPPULLUP_XMIN
|
||
#define ENDSTOPPULLUP_YMIN
|
||
#define ENDSTOPPULLUP_ZMIN
|
||
#endif
|
||
#ifndef DISABLE_Z_PROBE_ENDSTOP
|
||
#define ENDSTOPPULLUP_ZPROBE
|
||
#endif
|
||
#endif
|
||
|
||
/**
|
||
* Axis lengths
|
||
*/
|
||
#define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS)
|
||
#define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS)
|
||
#define Z_MAX_LENGTH (Z_MAX_POS - Z_MIN_POS)
|
||
|
||
/**
|
||
* SCARA
|
||
*/
|
||
#ifdef SCARA
|
||
#undef SLOWDOWN
|
||
#define QUICK_HOME //SCARA needs Quickhome
|
||
#endif
|
||
|
||
/**
|
||
* AUTOSET LOCATIONS OF LIMIT SWITCHES
|
||
* Added by ZetaPhoenix 09-15-2012
|
||
*/
|
||
#ifdef MANUAL_HOME_POSITIONS // Use manual limit switch locations
|
||
#define X_HOME_POS MANUAL_X_HOME_POS
|
||
#define Y_HOME_POS MANUAL_Y_HOME_POS
|
||
#define Z_HOME_POS MANUAL_Z_HOME_POS
|
||
#else //!MANUAL_HOME_POSITIONS – Use home switch positions based on homing direction and travel limits
|
||
#ifdef BED_CENTER_AT_0_0
|
||
#define X_HOME_POS X_MAX_LENGTH * X_HOME_DIR * 0.5
|
||
#define Y_HOME_POS Y_MAX_LENGTH * Y_HOME_DIR * 0.5
|
||
#else
|
||
#define X_HOME_POS (X_HOME_DIR < 0 ? X_MIN_POS : X_MAX_POS)
|
||
#define Y_HOME_POS (Y_HOME_DIR < 0 ? Y_MIN_POS : Y_MAX_POS)
|
||
#endif
|
||
#define Z_HOME_POS (Z_HOME_DIR < 0 ? Z_MIN_POS : Z_MAX_POS)
|
||
#endif //!MANUAL_HOME_POSITIONS
|
||
|
||
/**
|
||
* Auto Bed Leveling
|
||
*/
|
||
#ifdef ENABLE_AUTO_BED_LEVELING
|
||
// Boundaries for probing based on set limits
|
||
#define MIN_PROBE_X (max(X_MIN_POS, X_MIN_POS + X_PROBE_OFFSET_FROM_EXTRUDER))
|
||
#define MAX_PROBE_X (min(X_MAX_POS, X_MAX_POS + X_PROBE_OFFSET_FROM_EXTRUDER))
|
||
#define MIN_PROBE_Y (max(Y_MIN_POS, Y_MIN_POS + Y_PROBE_OFFSET_FROM_EXTRUDER))
|
||
#define MAX_PROBE_Y (min(Y_MAX_POS, Y_MAX_POS + Y_PROBE_OFFSET_FROM_EXTRUDER))
|
||
#endif
|
||
|
||
/**
|
||
* Sled Options
|
||
*/
|
||
#ifdef Z_PROBE_SLED
|
||
#define Z_SAFE_HOMING
|
||
#endif
|
||
|
||
/**
|
||
* MAX_STEP_FREQUENCY differs for TOSHIBA
|
||
*/
|
||
#ifdef CONFIG_STEPPERS_TOSHIBA
|
||
#define MAX_STEP_FREQUENCY 10000 // Max step frequency for Toshiba Stepper Controllers
|
||
#else
|
||
#define MAX_STEP_FREQUENCY 40000 // Max step frequency for Ultimaker (5000 pps / half step)
|
||
#endif
|
||
|
||
// MS1 MS2 Stepper Driver Microstepping mode table
|
||
#define MICROSTEP1 LOW,LOW
|
||
#define MICROSTEP2 HIGH,LOW
|
||
#define MICROSTEP4 LOW,HIGH
|
||
#define MICROSTEP8 HIGH,HIGH
|
||
#define MICROSTEP16 HIGH,HIGH
|
||
|
||
/**
|
||
* Advance calculated values
|
||
*/
|
||
#ifdef ADVANCE
|
||
#define EXTRUSION_AREA (0.25 * D_FILAMENT * D_FILAMENT * M_PI)
|
||
#define STEPS_PER_CUBIC_MM_E (axis_steps_per_unit[E_AXIS] / EXTRUSION_AREA)
|
||
#endif
|
||
|
||
#if defined(ULTIPANEL) && !defined(ELB_FULL_GRAPHIC_CONTROLLER)
|
||
#undef SDCARDDETECTINVERTED
|
||
#endif
|
||
|
||
// Power Signal Control Definitions
|
||
// By default use ATX definition
|
||
#ifndef POWER_SUPPLY
|
||
#define POWER_SUPPLY 1
|
||
#endif
|
||
#if (POWER_SUPPLY == 1) // 1 = ATX
|
||
#define PS_ON_AWAKE LOW
|
||
#define PS_ON_ASLEEP HIGH
|
||
#elif (POWER_SUPPLY == 2) // 2 = X-Box 360 203W
|
||
#define PS_ON_AWAKE HIGH
|
||
#define PS_ON_ASLEEP LOW
|
||
#endif
|
||
#define HAS_POWER_SWITCH (POWER_SUPPLY > 0 && PIN_EXISTS(PS_ON))
|
||
|
||
/**
|
||
* Temp Sensor defines
|
||
*/
|
||
#if TEMP_SENSOR_0 == -2
|
||
#define HEATER_0_USES_MAX6675
|
||
#elif TEMP_SENSOR_0 == -1
|
||
#define HEATER_0_USES_AD595
|
||
#elif TEMP_SENSOR_0 == 0
|
||
#undef HEATER_0_MINTEMP
|
||
#undef HEATER_0_MAXTEMP
|
||
#elif TEMP_SENSOR_0 > 0
|
||
#define THERMISTORHEATER_0 TEMP_SENSOR_0
|
||
#define HEATER_0_USES_THERMISTOR
|
||
#endif
|
||
|
||
#if TEMP_SENSOR_1 == -1
|
||
#define HEATER_1_USES_AD595
|
||
#elif TEMP_SENSOR_1 == 0
|
||
#undef HEATER_1_MINTEMP
|
||
#undef HEATER_1_MAXTEMP
|
||
#elif TEMP_SENSOR_1 > 0
|
||
#define THERMISTORHEATER_1 TEMP_SENSOR_1
|
||
#define HEATER_1_USES_THERMISTOR
|
||
#endif
|
||
|
||
#if TEMP_SENSOR_2 == -1
|
||
#define HEATER_2_USES_AD595
|
||
#elif TEMP_SENSOR_2 == 0
|
||
#undef HEATER_2_MINTEMP
|
||
#undef HEATER_2_MAXTEMP
|
||
#elif TEMP_SENSOR_2 > 0
|
||
#define THERMISTORHEATER_2 TEMP_SENSOR_2
|
||
#define HEATER_2_USES_THERMISTOR
|
||
#endif
|
||
|
||
#if TEMP_SENSOR_3 == -1
|
||
#define HEATER_3_USES_AD595
|
||
#elif TEMP_SENSOR_3 == 0
|
||
#undef HEATER_3_MINTEMP
|
||
#undef HEATER_3_MAXTEMP
|
||
#elif TEMP_SENSOR_3 > 0
|
||
#define THERMISTORHEATER_3 TEMP_SENSOR_3
|
||
#define HEATER_3_USES_THERMISTOR
|
||
#endif
|
||
|
||
#if TEMP_SENSOR_BED == -1
|
||
#define BED_USES_AD595
|
||
#elif TEMP_SENSOR_BED == 0
|
||
#undef BED_MINTEMP
|
||
#undef BED_MAXTEMP
|
||
#elif TEMP_SENSOR_BED > 0
|
||
#define THERMISTORBED TEMP_SENSOR_BED
|
||
#define BED_USES_THERMISTOR
|
||
#endif
|
||
|
||
/**
|
||
* ARRAY_BY_EXTRUDERS based on EXTRUDERS
|
||
*/
|
||
#if EXTRUDERS > 3
|
||
#define ARRAY_BY_EXTRUDERS(v1, v2, v3, v4) { v1, v2, v3, v4 }
|
||
#elif EXTRUDERS > 2
|
||
#define ARRAY_BY_EXTRUDERS(v1, v2, v3, v4) { v1, v2, v3 }
|
||
#elif EXTRUDERS > 1
|
||
#define ARRAY_BY_EXTRUDERS(v1, v2, v3, v4) { v1, v2 }
|
||
#else
|
||
#define ARRAY_BY_EXTRUDERS(v1, v2, v3, v4) { v1 }
|
||
#endif
|
||
|
||
/**
|
||
* Shorthand for pin tests, used wherever needed
|
||
*/
|
||
#define HAS_TEMP_0 (PIN_EXISTS(TEMP_0) && TEMP_SENSOR_0 != 0 && TEMP_SENSOR_0 != -2)
|
||
#define HAS_TEMP_1 (PIN_EXISTS(TEMP_1) && TEMP_SENSOR_1 != 0)
|
||
#define HAS_TEMP_2 (PIN_EXISTS(TEMP_2) && TEMP_SENSOR_2 != 0)
|
||
#define HAS_TEMP_3 (PIN_EXISTS(TEMP_3) && TEMP_SENSOR_3 != 0)
|
||
#define HAS_TEMP_BED (PIN_EXISTS(TEMP_BED) && TEMP_SENSOR_BED != 0)
|
||
#define HAS_HEATER_0 (PIN_EXISTS(HEATER_0))
|
||
#define HAS_HEATER_1 (PIN_EXISTS(HEATER_1))
|
||
#define HAS_HEATER_2 (PIN_EXISTS(HEATER_2))
|
||
#define HAS_HEATER_3 (PIN_EXISTS(HEATER_3))
|
||
#define HAS_HEATER_BED (PIN_EXISTS(HEATER_BED))
|
||
#define HAS_AUTO_FAN_0 (PIN_EXISTS(EXTRUDER_0_AUTO_FAN))
|
||
#define HAS_AUTO_FAN_1 (PIN_EXISTS(EXTRUDER_1_AUTO_FAN))
|
||
#define HAS_AUTO_FAN_2 (PIN_EXISTS(EXTRUDER_2_AUTO_FAN))
|
||
#define HAS_AUTO_FAN_3 (PIN_EXISTS(EXTRUDER_3_AUTO_FAN))
|
||
#define HAS_AUTO_FAN (HAS_AUTO_FAN_0 || HAS_AUTO_FAN_1 || HAS_AUTO_FAN_2 || HAS_AUTO_FAN_3)
|
||
#define HAS_FAN (PIN_EXISTS(FAN))
|
||
#define HAS_CONTROLLERFAN (PIN_EXISTS(CONTROLLERFAN))
|
||
#define HAS_SERVO_0 (PIN_EXISTS(SERVO0))
|
||
#define HAS_SERVO_1 (PIN_EXISTS(SERVO1))
|
||
#define HAS_SERVO_2 (PIN_EXISTS(SERVO2))
|
||
#define HAS_SERVO_3 (PIN_EXISTS(SERVO3))
|
||
#define HAS_FILAMENT_SENSOR (defined(FILAMENT_SENSOR) && PIN_EXISTS(FILWIDTH))
|
||
#define HAS_FILRUNOUT (PIN_EXISTS(FILRUNOUT))
|
||
#define HAS_HOME (PIN_EXISTS(HOME))
|
||
#define HAS_KILL (PIN_EXISTS(KILL))
|
||
#define HAS_SUICIDE (PIN_EXISTS(SUICIDE))
|
||
#define HAS_PHOTOGRAPH (PIN_EXISTS(PHOTOGRAPH))
|
||
#define HAS_X_MIN (PIN_EXISTS(X_MIN))
|
||
#define HAS_X_MAX (PIN_EXISTS(X_MAX))
|
||
#define HAS_Y_MIN (PIN_EXISTS(Y_MIN))
|
||
#define HAS_Y_MAX (PIN_EXISTS(Y_MAX))
|
||
#define HAS_Z_MIN (PIN_EXISTS(Z_MIN))
|
||
#define HAS_Z_MAX (PIN_EXISTS(Z_MAX))
|
||
#define HAS_Z2_MIN (PIN_EXISTS(Z2_MIN))
|
||
#define HAS_Z2_MAX (PIN_EXISTS(Z2_MAX))
|
||
#define HAS_Z_PROBE (PIN_EXISTS(Z_PROBE))
|
||
#define HAS_SOLENOID_1 (PIN_EXISTS(SOL1))
|
||
#define HAS_SOLENOID_2 (PIN_EXISTS(SOL2))
|
||
#define HAS_SOLENOID_3 (PIN_EXISTS(SOL3))
|
||
#define HAS_MICROSTEPS (PIN_EXISTS(X_MS1))
|
||
#define HAS_MICROSTEPS_E0 (PIN_EXISTS(E0_MS1))
|
||
#define HAS_MICROSTEPS_E1 (PIN_EXISTS(E1_MS1))
|
||
#define HAS_MICROSTEPS_E2 (PIN_EXISTS(E2_MS1))
|
||
#define HAS_X_ENABLE (PIN_EXISTS(X_ENABLE))
|
||
#define HAS_X2_ENABLE (PIN_EXISTS(X2_ENABLE))
|
||
#define HAS_Y_ENABLE (PIN_EXISTS(Y_ENABLE))
|
||
#define HAS_Y2_ENABLE (PIN_EXISTS(Y2_ENABLE))
|
||
#define HAS_Z_ENABLE (PIN_EXISTS(Z_ENABLE))
|
||
#define HAS_Z2_ENABLE (PIN_EXISTS(Z2_ENABLE))
|
||
#define HAS_E0_ENABLE (PIN_EXISTS(E0_ENABLE))
|
||
#define HAS_E1_ENABLE (PIN_EXISTS(E1_ENABLE))
|
||
#define HAS_E2_ENABLE (PIN_EXISTS(E2_ENABLE))
|
||
#define HAS_E3_ENABLE (PIN_EXISTS(E3_ENABLE))
|
||
#define HAS_X_DIR (PIN_EXISTS(X_DIR))
|
||
#define HAS_X2_DIR (PIN_EXISTS(X2_DIR))
|
||
#define HAS_Y_DIR (PIN_EXISTS(Y_DIR))
|
||
#define HAS_Y2_DIR (PIN_EXISTS(Y2_DIR))
|
||
#define HAS_Z_DIR (PIN_EXISTS(Z_DIR))
|
||
#define HAS_Z2_DIR (PIN_EXISTS(Z2_DIR))
|
||
#define HAS_E0_DIR (PIN_EXISTS(E0_DIR))
|
||
#define HAS_E1_DIR (PIN_EXISTS(E1_DIR))
|
||
#define HAS_E2_DIR (PIN_EXISTS(E2_DIR))
|
||
#define HAS_E3_DIR (PIN_EXISTS(E3_DIR))
|
||
#define HAS_X_STEP (PIN_EXISTS(X_STEP))
|
||
#define HAS_X2_STEP (PIN_EXISTS(X2_STEP))
|
||
#define HAS_Y_STEP (PIN_EXISTS(Y_STEP))
|
||
#define HAS_Y2_STEP (PIN_EXISTS(Y2_STEP))
|
||
#define HAS_Z_STEP (PIN_EXISTS(Z_STEP))
|
||
#define HAS_Z2_STEP (PIN_EXISTS(Z2_STEP))
|
||
#define HAS_E0_STEP (PIN_EXISTS(E0_STEP))
|
||
#define HAS_E1_STEP (PIN_EXISTS(E1_STEP))
|
||
#define HAS_E2_STEP (PIN_EXISTS(E2_STEP))
|
||
#define HAS_E3_STEP (PIN_EXISTS(E3_STEP))
|
||
|
||
/**
|
||
* Helper Macros for heaters and extruder fan
|
||
*/
|
||
#define WRITE_HEATER_0P(v) WRITE(HEATER_0_PIN, v)
|
||
#if EXTRUDERS > 1 || defined(HEATERS_PARALLEL)
|
||
#define WRITE_HEATER_1(v) WRITE(HEATER_1_PIN, v)
|
||
#if EXTRUDERS > 2
|
||
#define WRITE_HEATER_2(v) WRITE(HEATER_2_PIN, v)
|
||
#if EXTRUDERS > 3
|
||
#define WRITE_HEATER_3(v) WRITE(HEATER_3_PIN, v)
|
||
#endif
|
||
#endif
|
||
#endif
|
||
#ifdef HEATERS_PARALLEL
|
||
#define WRITE_HEATER_0(v) { WRITE_HEATER_0P(v); WRITE_HEATER_1(v); }
|
||
#else
|
||
#define WRITE_HEATER_0(v) WRITE_HEATER_0P(v)
|
||
#endif
|
||
#if HAS_HEATER_BED
|
||
#define WRITE_HEATER_BED(v) WRITE(HEATER_BED_PIN, v)
|
||
#endif
|
||
#if HAS_FAN
|
||
#define WRITE_FAN(v) WRITE(FAN_PIN, v)
|
||
#endif
|
||
|
||
#endif //CONFIGURATION_LCD
|
||
#endif //CONDITIONALS_H
|