This repository has been archived on 2022-01-28. You can view files and clone it, but cannot push or open issues or pull requests.
Marlin-Artillery-M600/Marlin/pins_MIGHTYBOARD_REVE.h
2017-05-17 04:23:06 -05:00

336 lines
9.6 KiB
C

/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* Mightyboard Rev.E pin assignments
*/
/**
*
* This is a starting-point to support the Makerbot Replicator series of 3D printers.
* It's not functional because Marlin has limited support for some features.
* Marlin will need the following augmentations before it will be supportable:
*
* - Support for two or more MAX6675 thermocouples
* - Support for multiple i2c buses to control the MCP4018 digital pots
* - Support for one additional unidirectional SPI bus, to read the thermocouples
* - Support for an RGB LED that may work differently from BLINKM
*
* The MCP4018 requires separate I2C buses because it has a fixed address (0x2F << 1 = 0x5E)
* The thermocouples share the same SCK and DO pins, with their own CS pins.
* The controller interface port connects to a 3-wire shift-register display controller
*
*/
/**
* Rev B 2 JAN 2017
*
* Added pin definitions for:
* M3, M4 & M5 spindle control commands
* case light
*
* Corrected pin assignment for MOSFET_B_PIN pin. Changed it from 9 to 11. The port
* number (B5) agrees with the schematic but B5 is assigned to logical pin 11.
*/
#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
#error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu."
#endif
#define DEFAULT_MACHINE_NAME "MB Replicator"
#define BOARD_NAME "Mightyboard"
#define LARGE_FLASH true
//
// Servos
//
#define SERVO0_PIN 36 // C1 (1280-EX1)
#define SERVO1_PIN 37 // C0 (1280-EX2)
#define SERVO2_PIN 40 // G1 (1280-EX3)
#define SERVO3_PIN 41 // G0 (1280-EX4)
//
// Limit Switches
//
#define X_MIN_PIN 49 // L0
#define X_MAX_PIN 48 // L1
#define Y_MIN_PIN 47 // L2
#define Y_MAX_PIN 46 // L3
#define Z_MIN_PIN 43 // L6
#define Z_MAX_PIN 42 // L7
//
// Z Probe (when not Z_MIN_PIN)
//
#ifndef Z_MIN_PROBE_PIN
#define Z_MIN_PROBE_PIN 42
#endif
//
// Steppers
//
#define X_STEP_PIN 55 // F1
#define X_DIR_PIN 54 // F0
#define X_ENABLE_PIN 56 // F2
#define Y_STEP_PIN 59 // F5
#define Y_DIR_PIN 58 // F4
#define Y_ENABLE_PIN 60 // F6
#define Z_STEP_PIN 63 // K1
#define Z_DIR_PIN 62 // K0
#define Z_ENABLE_PIN 64 // K2
#define E0_STEP_PIN 25 // A3
#define E0_DIR_PIN 24 // A2
#define E0_ENABLE_PIN 26 // A4
#define E1_STEP_PIN 29 // A7
#define E1_DIR_PIN 28 // A6
#define E1_ENABLE_PIN 39 // G2
//
// I2C Digipots - MCP4018
// Address 5E (2F << 1)
// Set from 0 - 127 with stop bit.
// (Ex. 3F << 1 | 1)
//
#define DIGIPOTS_I2C_SCL 76 // J5
#define DIGIPOTS_I2C_SDA_X 57 // F3
#define DIGIPOTS_I2C_SDA_Y 61 // F7
#define DIGIPOTS_I2C_SDA_Z 65 // K3
#define DIGIPOTS_I2C_SDA_E0 27 // A5
#define DIGIPOTS_I2C_SDA_E1 77 // J6
//
// Temperature Sensors
//
#define TEMP_BED_PIN 69 // K7
// SPI for Max6675 or Max31855 Thermocouple
// Uses a separate SPI bus
//
// 3 E5 DO (SO)
// 5 E3 CS1
// 2 E4 CS2
// 78 E2 SCK
//
#define THERMO_SCK_PIN 78 // E2
#define THERMO_DO_PIN 3 // E5
#define THERMO_CS1 5 // E3
#define THERMO_CS2 2 // E4
#define MAX6675_SS THERMO_CS1
#define MAX6675_SCK_PIN THERMO_SCK_PIN
#define MAX6675_DO_PIN THERMO_DO_PIN
//
// Augmentation for auto-assigning plugs
//
// Two thermocouple connectors allows for either
// 2 extruders or 1 extruder and a heated bed.
// With no heated bed, an additional 24V fan is possible.
//
#define MOSFET_A_PIN 6 // H3
#define MOSFET_B_PIN 11 // B5 - Rev A of this file had this pin assigned to 9
#define MOSFET_C_PIN 45 // L4
#define MOSFET_D_PIN 44 // L5
#if HOTENDS > 1
#if TEMP_SENSOR_BED
#define IS_EEB
#else
#define IS_EEF
#endif
#elif TEMP_SENSOR_BED
#define IS_EFB
#else
#define IS_EFF
#endif
//
// Heaters / Fans (24V)
//
#define HEATER_0_PIN MOSFET_A_PIN
#if ENABLED(IS_EFB) // Hotend, Fan, Bed
#define FAN_PIN MOSFET_B_PIN
#define HEATER_BED_PIN MOSFET_C_PIN
#elif ENABLED(IS_EEF) // Hotend, Hotend, Fan
#define HEATER_1_PIN MOSFET_B_PIN
#define FAN_PIN MOSFET_C_PIN
#elif ENABLED(IS_EEB) // Hotend, Hotend, Bed
#define HEATER_1_PIN MOSFET_B_PIN
#define HEATER_BED_PIN MOSFET_C_PIN
#elif ENABLED(IS_EFF) // Hotend, Fan, Fan
#define FAN_PIN MOSFET_B_PIN
#define FAN1_PIN MOSFET_C_PIN
#elif ENABLED(IS_SF) // Spindle, Fan
#define FAN_PIN MOSFET_C_PIN
#endif
#ifndef FAN_PIN
#define FAN_PIN MOSFET_D_PIN
#endif
//
// Extruder Auto Fan Pins
//
#define ORIG_E0_AUTO_FAN_PIN 7 // H4
#define ORIG_E1_AUTO_FAN_PIN 12 // B6
//
// Misc. Functions
//
#define LED_PIN 13 // B7
#define CUTOFF_RESET_PIN 16 // H1
#define CUTOFF_TEST_PIN 17 // H0
#define CASE_LIGHT_PIN 44 // L5 MUST BE HARDWARE PWM
//
// LCD / Controller
//
#ifdef REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
#define LCD_PINS_RS 33 // C4, LCD-STROBE
#define LCD_PINS_ENABLE 72 // J2, LEFT
#define LCD_PINS_D4 35 // C2, LCD-CLK
#define LCD_PINS_D5 32 // C5, RLED
#define LCD_PINS_D6 34 // C3, LCD-DATA
#define LCD_PINS_D7 31 // C6, GLED
#define BTN_EN2 75 // J4, UP
#define BTN_EN1 73 // J3, DOWN
//STOP button connected as KILL_PIN
#define KILL_PIN 14 // J1, RIGHT
//KILL - not connected
#define BEEPER_PIN 8 // H5, SD_WP
#define BTN_CENTER 15 // J0
#define BTN_ENC BTN_CENTER
//on board leds
#define STAT_LED_RED_LED SERVO0_PIN // C1 (1280-EX1, DEBUG2)
#define STAT_LED_BLUE_PIN SERVO1_PIN // C0 (1280-EX2, DEBUG3)
#else
// Replicator uses a 3-wire SR controller with HD44780
// For now, pretend it's the SAV
//
#define SAV_3DLCD
#define SR_DATA_PIN 34 // C3
#define SR_CLK_PIN 35 // C2
#define SR_STROBE_PIN 33 // C4
#define BTN_UP 75 // J4
#define BTN_DOWN 73 // J3
#define BTN_LEFT 72 // J2
#define BTN_RIGHT 14 // J1
#define BTN_CENTER 15 // J0
#define BTN_ENC BTN_CENTER
#define BEEPER_PIN 4 // G5
#define STAT_LED_RED_PIN 32 // C5
#define STAT_LED_BLUE_PIN 31 // C6 (Actually green)
#endif
//
// SD Card
//
#define SDSS 53 // B0
#define SD_DETECT_PIN 9 // H6
#define MAX_PIN THERMO_SCK_PIN
//
// M3/M4/M5 - Spindle/Laser Control
//
#define SPINDLE_LASER_ENABLE_PIN 66 // K4 Pin should have a pullup!
#define SPINDLE_LASER_PWM_PIN 8 // H5 MUST BE HARDWARE PWM
#define SPINDLE_DIR_PIN 67 // K5
// Check if all pins are defined in mega/pins_arduino.h
#include <Arduino.h>
static_assert(NUM_DIGITAL_PINS > MAX_PIN, "add missing pins to [arduino dir]/hardware/arduino/avr/variants/mega/pins_arduino.h based on fastio.h"
"to digital_pin_to_port_PGM, digital_pin_to_bit_mask_PGM, digital_pin_to_timer_PGM, NUM_DIGITAL_PINS, see below");
/* in [arduino dir]/hardware/arduino/avr/variants/mega/pins_arduino.h
change:
#define NUM_DIGITAL_PINS 70
to:
#define NUM_DIGITAL_PINS 80
to digital_pin_to_port_PGM add at the end:
const uint8_t PROGMEM digital_pin_to_port_PGM[] = {
....
PG , // PG 4 ** 70 **
PG , // PG 3 ** 71 **
PJ , // PJ 2 ** 72 **
PJ , // PJ 3 ** 73 **
PJ , // PJ 7 ** 74 **
PJ , // PJ 4 ** 75 **
PJ , // PJ 5 ** 76 **
PJ , // PJ 6 ** 77 **
PE , // PE 2 ** 78 **
PE , // PE 6 ** 79 **
};
to digital_pin_to_bit_mask_PGM add at the end:
const uint8_t PROGMEM digital_pin_to_bit_mask_PGM[] = {
....
_BV( 4 ) , // PG 4 ** 70 **
_BV( 3 ) , // PG 3 ** 71 **
_BV( 2 ) , // PJ 2 ** 72 **
_BV( 3 ) , // PJ 3 ** 73 **
_BV( 7 ) , // PJ 7 ** 74 **
_BV( 4 ) , // PJ 4 ** 75 **
_BV( 5 ) , // PJ 5 ** 76 **
_BV( 6 ) , // PJ 6 ** 77 **
_BV( 2 ) , // PE 2 ** 78 **
_BV( 6 ) , // PE 6 ** 79 **
};
to digital_pin_to_timer_PGM add at the end:
const uint8_t PROGMEM digital_pin_to_timer_PGM[] = {
....
NOT_ON_TIMER , // PG 4 ** 70 **
NOT_ON_TIMER , // PG 3 ** 71 **
NOT_ON_TIMER , // PJ 2 ** 72 **
NOT_ON_TIMER , // PJ 3 ** 73 **
NOT_ON_TIMER , // PJ 7 ** 74 **
NOT_ON_TIMER , // PJ 4 ** 75 **
NOT_ON_TIMER , // PJ 5 ** 76 **
NOT_ON_TIMER , // PJ 6 ** 77 **
NOT_ON_TIMER , // PE 2 ** 78 **
NOT_ON_TIMER , // PE 6 ** 79 **
};
*/