1730 lines
65 KiB
C
1730 lines
65 KiB
C
/**
|
||
* Marlin 3D Printer Firmware
|
||
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||
*
|
||
* Based on Sprinter and grbl.
|
||
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
||
*
|
||
* This program is free software: you can redistribute it and/or modify
|
||
* it under the terms of the GNU General Public License as published by
|
||
* the Free Software Foundation, either version 3 of the License, or
|
||
* (at your option) any later version.
|
||
*
|
||
* This program is distributed in the hope that it will be useful,
|
||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||
* GNU General Public License for more details.
|
||
*
|
||
* You should have received a copy of the GNU General Public License
|
||
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||
*
|
||
*/
|
||
|
||
/**
|
||
* Configuration.h
|
||
*
|
||
* Basic settings such as:
|
||
*
|
||
* - Type of electronics
|
||
* - Type of temperature sensor
|
||
* - Printer geometry
|
||
* - Endstop configuration
|
||
* - LCD controller
|
||
* - Extra features
|
||
*
|
||
* Advanced settings can be found in Configuration_adv.h
|
||
*
|
||
*/
|
||
#ifndef CONFIGURATION_H
|
||
#define CONFIGURATION_H
|
||
|
||
/**
|
||
*
|
||
* ***********************************
|
||
* ** ATTENTION TO ALL DEVELOPERS **
|
||
* ***********************************
|
||
*
|
||
* You must increment this version number for every significant change such as,
|
||
* but not limited to: ADD, DELETE RENAME OR REPURPOSE any directive/option.
|
||
*
|
||
* Note: Update also Version.h !
|
||
*/
|
||
#define CONFIGURATION_H_VERSION 010100
|
||
|
||
//===========================================================================
|
||
//============================= Getting Started =============================
|
||
//===========================================================================
|
||
|
||
/**
|
||
* Here are some standard links for getting your machine calibrated:
|
||
*
|
||
* http://reprap.org/wiki/Calibration
|
||
* http://youtu.be/wAL9d7FgInk
|
||
* http://calculator.josefprusa.cz
|
||
* http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
|
||
* http://www.thingiverse.com/thing:5573
|
||
* https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
|
||
* http://www.thingiverse.com/thing:298812
|
||
*/
|
||
|
||
//===========================================================================
|
||
//============================= DELTA Printer ===============================
|
||
//===========================================================================
|
||
// For Delta printers start with one of the configuration files in the
|
||
// example_configurations/delta directory and customize for your machine.
|
||
//
|
||
|
||
//===========================================================================
|
||
//============================= SCARA Printer ===============================
|
||
//===========================================================================
|
||
// For a Scara printer replace the configuration files with the files in the
|
||
// example_configurations/SCARA directory.
|
||
//
|
||
|
||
// @section info
|
||
|
||
// User-specified version info of this build to display in [Pronterface, etc] terminal window during
|
||
// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
|
||
// build by the user have been successfully uploaded into firmware.
|
||
#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
|
||
#define SHOW_BOOTSCREEN
|
||
#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
|
||
#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
|
||
|
||
//
|
||
// *** VENDORS PLEASE READ *****************************************************
|
||
//
|
||
// Marlin now allow you to have a vendor boot image to be displayed on machine
|
||
// start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your
|
||
// custom boot image and then the default Marlin boot image is shown.
|
||
//
|
||
// We suggest for you to take advantage of this new feature and keep the Marlin
|
||
// boot image unmodified. For an example have a look at the bq Hephestos 2
|
||
// example configuration folder.
|
||
//
|
||
//#define SHOW_CUSTOM_BOOTSCREEN
|
||
// @section machine
|
||
|
||
/**
|
||
* Select which serial port on the board will be used for communication with the host.
|
||
* This allows the connection of wireless adapters (for instance) to non-default port pins.
|
||
* Serial port 0 is always used by the Arduino bootloader regardless of this setting.
|
||
*
|
||
* :[0, 1, 2, 3, 4, 5, 6, 7]
|
||
*/
|
||
#define SERIAL_PORT 0
|
||
|
||
/**
|
||
* This setting determines the communication speed of the printer.
|
||
*
|
||
* 250000 works in most cases, but you might try a lower speed if
|
||
* you commonly experience drop-outs during host printing.
|
||
*
|
||
* :[2400, 9600, 19200, 38400, 57600, 115200, 250000]
|
||
*/
|
||
#define BAUDRATE 250000
|
||
|
||
// Enable the Bluetooth serial interface on AT90USB devices
|
||
//#define BLUETOOTH
|
||
|
||
// The following define selects which electronics board you have.
|
||
// Please choose the name from boards.h that matches your setup
|
||
#ifndef MOTHERBOARD
|
||
#define MOTHERBOARD BOARD_RAMPS_14_EFB
|
||
#endif
|
||
|
||
// Optional custom name for your RepStrap or other custom machine
|
||
// Displayed in the LCD "Ready" message
|
||
#define CUSTOM_MACHINE_NAME "Deltabot"
|
||
|
||
// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
|
||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||
|
||
// This defines the number of extruders
|
||
// :[1, 2, 3, 4, 5]
|
||
#define EXTRUDERS 1
|
||
|
||
// Enable if your E steppers or extruder gear ratios are not identical
|
||
//#define DISTINCT_E_FACTORS
|
||
|
||
// For Cyclops or any "multi-extruder" that shares a single nozzle.
|
||
//#define SINGLENOZZLE
|
||
|
||
// A dual extruder that uses a single stepper motor
|
||
// Don't forget to set SSDE_SERVO_ANGLES and HOTEND_OFFSET_X/Y/Z
|
||
//#define SWITCHING_EXTRUDER
|
||
#if ENABLED(SWITCHING_EXTRUDER)
|
||
#define SWITCHING_EXTRUDER_SERVO_NR 0
|
||
#define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1
|
||
//#define HOTEND_OFFSET_Z {0.0, 0.0}
|
||
#endif
|
||
|
||
/**
|
||
* "Mixing Extruder"
|
||
* - Adds a new code, M165, to set the current mix factors.
|
||
* - Extends the stepping routines to move multiple steppers in proportion to the mix.
|
||
* - Optional support for Repetier Firmware M163, M164, and virtual extruder.
|
||
* - This implementation supports only a single extruder.
|
||
* - Enable DIRECT_MIXING_IN_G1 for Pia Taubert's reference implementation
|
||
*/
|
||
//#define MIXING_EXTRUDER
|
||
#if ENABLED(MIXING_EXTRUDER)
|
||
#define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder
|
||
#define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164
|
||
//#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands
|
||
#endif
|
||
|
||
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
||
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
||
// For the other hotends it is their distance from the extruder 0 hotend.
|
||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||
|
||
/**
|
||
* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
|
||
*
|
||
* 0 = No Power Switch
|
||
* 1 = ATX
|
||
* 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
|
||
*
|
||
* :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
|
||
*/
|
||
#define POWER_SUPPLY 1
|
||
|
||
#if POWER_SUPPLY > 0
|
||
// Enable this option to leave the PSU off at startup.
|
||
// Power to steppers and heaters will need to be turned on with M80.
|
||
//#define PS_DEFAULT_OFF
|
||
#endif
|
||
|
||
// @section temperature
|
||
|
||
//===========================================================================
|
||
//============================= Thermal Settings ============================
|
||
//===========================================================================
|
||
|
||
/**
|
||
* --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
|
||
*
|
||
* Temperature sensors available:
|
||
*
|
||
* -3 : thermocouple with MAX31855 (only for sensor 0)
|
||
* -2 : thermocouple with MAX6675 (only for sensor 0)
|
||
* -1 : thermocouple with AD595
|
||
* 0 : not used
|
||
* 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
|
||
* 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
|
||
* 3 : Mendel-parts thermistor (4.7k pullup)
|
||
* 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
|
||
* 5 : 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
|
||
* 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
|
||
* 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
|
||
* 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
|
||
* 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
|
||
* 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
|
||
* 10 : 100k RS thermistor 198-961 (4.7k pullup)
|
||
* 11 : 100k beta 3950 1% thermistor (4.7k pullup)
|
||
* 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
|
||
* 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
|
||
* 20 : the PT100 circuit found in the Ultimainboard V2.x
|
||
* 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
|
||
* 66 : 4.7M High Temperature thermistor from Dyze Design
|
||
* 70 : the 100K thermistor found in the bq Hephestos 2
|
||
* 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
|
||
*
|
||
* 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
|
||
* (but gives greater accuracy and more stable PID)
|
||
* 51 : 100k thermistor - EPCOS (1k pullup)
|
||
* 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
|
||
* 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
|
||
*
|
||
* 1047 : Pt1000 with 4k7 pullup
|
||
* 1010 : Pt1000 with 1k pullup (non standard)
|
||
* 147 : Pt100 with 4k7 pullup
|
||
* 110 : Pt100 with 1k pullup (non standard)
|
||
*
|
||
* Use these for Testing or Development purposes. NEVER for production machine.
|
||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||
*
|
||
* :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '66':"Dyze Design 4.7M High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" }
|
||
*/
|
||
#define TEMP_SENSOR_0 -1
|
||
#define TEMP_SENSOR_1 0
|
||
#define TEMP_SENSOR_2 0
|
||
#define TEMP_SENSOR_3 0
|
||
#define TEMP_SENSOR_4 0
|
||
#define TEMP_SENSOR_BED 0
|
||
|
||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||
#define DUMMY_THERMISTOR_998_VALUE 25
|
||
#define DUMMY_THERMISTOR_999_VALUE 100
|
||
|
||
// Use temp sensor 1 as a redundant sensor with sensor 0. If the readings
|
||
// from the two sensors differ too much the print will be aborted.
|
||
//#define TEMP_SENSOR_1_AS_REDUNDANT
|
||
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
|
||
|
||
// Extruder temperature must be close to target for this long before M109 returns success
|
||
#define TEMP_RESIDENCY_TIME 10 // (seconds)
|
||
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
|
||
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
|
||
|
||
// Bed temperature must be close to target for this long before M190 returns success
|
||
#define TEMP_BED_RESIDENCY_TIME 0 // (seconds)
|
||
#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
|
||
#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
|
||
|
||
// The minimal temperature defines the temperature below which the heater will not be enabled It is used
|
||
// to check that the wiring to the thermistor is not broken.
|
||
// Otherwise this would lead to the heater being powered on all the time.
|
||
#define HEATER_0_MINTEMP 5
|
||
#define HEATER_1_MINTEMP 5
|
||
#define HEATER_2_MINTEMP 5
|
||
#define HEATER_3_MINTEMP 5
|
||
#define HEATER_4_MINTEMP 5
|
||
#define BED_MINTEMP 5
|
||
|
||
// When temperature exceeds max temp, your heater will be switched off.
|
||
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
|
||
// You should use MINTEMP for thermistor short/failure protection.
|
||
#define HEATER_0_MAXTEMP 275
|
||
#define HEATER_1_MAXTEMP 275
|
||
#define HEATER_2_MAXTEMP 275
|
||
#define HEATER_3_MAXTEMP 275
|
||
#define HEATER_4_MAXTEMP 275
|
||
#define BED_MAXTEMP 150
|
||
|
||
//===========================================================================
|
||
//============================= PID Settings ================================
|
||
//===========================================================================
|
||
// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
|
||
|
||
// Comment the following line to disable PID and enable bang-bang.
|
||
#define PIDTEMP
|
||
#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
|
||
#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
|
||
#if ENABLED(PIDTEMP)
|
||
//#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
|
||
//#define PID_DEBUG // Sends debug data to the serial port.
|
||
//#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||
//#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
|
||
// Set/get with gcode: M301 E[extruder number, 0-2]
|
||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||
#define K1 0.95 //smoothing factor within the PID
|
||
|
||
// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
|
||
// Ultimaker
|
||
#define DEFAULT_Kp 22.2
|
||
#define DEFAULT_Ki 1.08
|
||
#define DEFAULT_Kd 114
|
||
|
||
// MakerGear
|
||
//#define DEFAULT_Kp 7.0
|
||
//#define DEFAULT_Ki 0.1
|
||
//#define DEFAULT_Kd 12
|
||
|
||
// Mendel Parts V9 on 12V
|
||
//#define DEFAULT_Kp 63.0
|
||
//#define DEFAULT_Ki 2.25
|
||
//#define DEFAULT_Kd 440
|
||
|
||
#endif // PIDTEMP
|
||
|
||
//===========================================================================
|
||
//============================= PID > Bed Temperature Control ===============
|
||
//===========================================================================
|
||
// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
|
||
//
|
||
// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
|
||
// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
|
||
// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
|
||
// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
|
||
// If your configuration is significantly different than this and you don't understand the issues involved, you probably
|
||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||
// If this is enabled, find your own PID constants below.
|
||
//#define PIDTEMPBED
|
||
|
||
//#define BED_LIMIT_SWITCHING
|
||
|
||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||
|
||
#if ENABLED(PIDTEMPBED)
|
||
|
||
//#define PID_BED_DEBUG // Sends debug data to the serial port.
|
||
|
||
//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||
//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||
#define DEFAULT_bedKp 10.00
|
||
#define DEFAULT_bedKi .023
|
||
#define DEFAULT_bedKd 305.4
|
||
|
||
//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||
//from pidautotune
|
||
//#define DEFAULT_bedKp 97.1
|
||
//#define DEFAULT_bedKi 1.41
|
||
//#define DEFAULT_bedKd 1675.16
|
||
|
||
// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
|
||
#endif // PIDTEMPBED
|
||
|
||
// @section extruder
|
||
|
||
// This option prevents extrusion if the temperature is below EXTRUDE_MINTEMP.
|
||
// It also enables the M302 command to set the minimum extrusion temperature
|
||
// or to allow moving the extruder regardless of the hotend temperature.
|
||
// *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
|
||
#define PREVENT_COLD_EXTRUSION
|
||
#define EXTRUDE_MINTEMP 170
|
||
|
||
// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
|
||
// Note that for Bowden Extruders a too-small value here may prevent loading.
|
||
#define PREVENT_LENGTHY_EXTRUDE
|
||
#define EXTRUDE_MAXLENGTH 200
|
||
|
||
//===========================================================================
|
||
//======================== Thermal Runaway Protection =======================
|
||
//===========================================================================
|
||
|
||
/**
|
||
* Thermal Protection protects your printer from damage and fire if a
|
||
* thermistor falls out or temperature sensors fail in any way.
|
||
*
|
||
* The issue: If a thermistor falls out or a temperature sensor fails,
|
||
* Marlin can no longer sense the actual temperature. Since a disconnected
|
||
* thermistor reads as a low temperature, the firmware will keep the heater on.
|
||
*
|
||
* If you get "Thermal Runaway" or "Heating failed" errors the
|
||
* details can be tuned in Configuration_adv.h
|
||
*/
|
||
|
||
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
|
||
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
|
||
|
||
//===========================================================================
|
||
//============================= Mechanical Settings =========================
|
||
//===========================================================================
|
||
|
||
// @section machine
|
||
|
||
// Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics
|
||
// either in the usual order or reversed
|
||
//#define COREXY
|
||
//#define COREXZ
|
||
//#define COREYZ
|
||
//#define COREYX
|
||
//#define COREZX
|
||
//#define COREZY
|
||
|
||
//===========================================================================
|
||
//============================== Delta Settings =============================
|
||
//===========================================================================
|
||
// Enable DELTA kinematics and most of the default configuration for Deltas
|
||
#define DELTA
|
||
|
||
#if ENABLED(DELTA)
|
||
|
||
// Make delta curves from many straight lines (linear interpolation).
|
||
// This is a trade-off between visible corners (not enough segments)
|
||
// and processor overload (too many expensive sqrt calls).
|
||
#define DELTA_SEGMENTS_PER_SECOND 200
|
||
|
||
// Center-to-center distance of the holes in the diagonal push rods.
|
||
#define DELTA_DIAGONAL_ROD 250.0 // mm
|
||
|
||
// Horizontal offset from middle of printer to smooth rod center.
|
||
#define DELTA_SMOOTH_ROD_OFFSET 175.0 // mm
|
||
|
||
// Horizontal offset of the universal joints on the end effector.
|
||
#define DELTA_EFFECTOR_OFFSET 33.0 // mm
|
||
|
||
// Horizontal offset of the universal joints on the carriages.
|
||
#define DELTA_CARRIAGE_OFFSET 18.0 // mm
|
||
|
||
// Horizontal distance bridged by diagonal push rods when effector is centered.
|
||
#define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-(DELTA_EFFECTOR_OFFSET)-(DELTA_CARRIAGE_OFFSET))
|
||
|
||
// height from z=0.00 to home position
|
||
#define DELTA_HEIGHT 250 // get this value from auto calibrate
|
||
|
||
// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
|
||
#define DELTA_PRINTABLE_RADIUS 140.0
|
||
|
||
// Delta calibration menu
|
||
// See http://minow.blogspot.com/index.html#4918805519571907051
|
||
//#define DELTA_CALIBRATION_MENU
|
||
|
||
// G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
|
||
//#define DELTA_AUTO_CALIBRATION
|
||
#if ENABLED(DELTA_AUTO_CALIBRATION)
|
||
#define DELTA_CALIBRATION_DEFAULT_POINTS 3 // set the default number of probe points : n*n (1-4)
|
||
#define DELTA_CALIBRATION_RADIUS (DELTA_PRINTABLE_RADIUS - 15) // set the radius for the calibration probe points
|
||
#endif
|
||
|
||
// After homing move down to a height where XY movement is unconstrained
|
||
#define DELTA_HOME_TO_SAFE_ZONE
|
||
|
||
//#define DELTA_ENDSTOP_ADJ { 0, 0, 0 }
|
||
|
||
// Trim adjustments for individual towers
|
||
#define DELTA_RADIUS_TRIM_TOWER_1 0.0
|
||
#define DELTA_RADIUS_TRIM_TOWER_2 0.0
|
||
#define DELTA_RADIUS_TRIM_TOWER_3 0.0
|
||
#define DELTA_DIAGONAL_ROD_TRIM_TOWER_1 0.0
|
||
#define DELTA_DIAGONAL_ROD_TRIM_TOWER_2 0.0
|
||
#define DELTA_DIAGONAL_ROD_TRIM_TOWER_3 0.0
|
||
#define DELTA_TOWER_ANGLE_TRIM_1 0.0
|
||
#define DELTA_TOWER_ANGLE_TRIM_2 0.0
|
||
#define DELTA_TOWER_ANGLE_TRIM_3 0.0
|
||
|
||
#endif
|
||
|
||
//===========================================================================
|
||
//============================== Endstop Settings ===========================
|
||
//===========================================================================
|
||
|
||
// @section homing
|
||
|
||
// Specify here all the endstop connectors that are connected to any endstop or probe.
|
||
// Almost all printers will be using one per axis. Probes will use one or more of the
|
||
// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
|
||
//#define USE_XMIN_PLUG
|
||
//#define USE_YMIN_PLUG
|
||
#define USE_ZMIN_PLUG // a Z probe
|
||
#define USE_XMAX_PLUG
|
||
#define USE_YMAX_PLUG
|
||
#define USE_ZMAX_PLUG
|
||
|
||
// coarse Endstop Settings
|
||
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
|
||
|
||
#if DISABLED(ENDSTOPPULLUPS)
|
||
// fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
|
||
//#define ENDSTOPPULLUP_XMAX
|
||
//#define ENDSTOPPULLUP_YMAX
|
||
//#define ENDSTOPPULLUP_ZMAX
|
||
//#define ENDSTOPPULLUP_XMIN
|
||
//#define ENDSTOPPULLUP_YMIN
|
||
//#define ENDSTOPPULLUP_ZMIN
|
||
//#define ENDSTOPPULLUP_ZMIN_PROBE
|
||
#endif
|
||
|
||
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
|
||
#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
|
||
#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
|
||
#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
|
||
#define X_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
|
||
#define Y_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
|
||
#define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
|
||
#define Z_MIN_PROBE_ENDSTOP_INVERTING true // set to true to invert the logic of the probe.
|
||
|
||
// Enable this feature if all enabled endstop pins are interrupt-capable.
|
||
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
|
||
//#define ENDSTOP_INTERRUPTS_FEATURE
|
||
|
||
//=============================================================================
|
||
//============================== Movement Settings ============================
|
||
//=============================================================================
|
||
// @section motion
|
||
|
||
// delta speeds must be the same on xyz
|
||
/**
|
||
* Default Settings
|
||
*
|
||
* These settings can be reset by M502
|
||
*
|
||
* You can set distinct factors for each E stepper, if needed.
|
||
* If fewer factors are given, the last will apply to the rest.
|
||
*
|
||
* Note that if EEPROM is enabled, saved values will override these.
|
||
*/
|
||
|
||
/**
|
||
* Default Axis Steps Per Unit (steps/mm)
|
||
* Override with M92
|
||
* X, Y, Z, E0 [, E1[, E2[, E3]]]
|
||
*/
|
||
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 80, 760*1.1 } // default steps per unit for Kossel (GT2, 20 tooth)
|
||
|
||
/**
|
||
* Default Max Feed Rate (mm/s)
|
||
* Override with M203
|
||
* X, Y, Z, E0 [, E1[, E2[, E3]]]
|
||
*/
|
||
#define DEFAULT_MAX_FEEDRATE { 500, 500, 500, 25 }
|
||
|
||
/**
|
||
* Default Max Acceleration (change/s) change = mm/s
|
||
* (Maximum start speed for accelerated moves)
|
||
* Override with M201
|
||
* X, Y, Z, E0 [, E1[, E2[, E3]]]
|
||
*/
|
||
#define DEFAULT_MAX_ACCELERATION { 9000, 9000, 9000, 10000 }
|
||
|
||
/**
|
||
* Default Acceleration (change/s) change = mm/s
|
||
* Override with M204
|
||
*
|
||
* M204 P Acceleration
|
||
* M204 R Retract Acceleration
|
||
* M204 T Travel Acceleration
|
||
*/
|
||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
|
||
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
|
||
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
|
||
|
||
/**
|
||
* Default Jerk (mm/s)
|
||
* Override with M205 X Y Z E
|
||
*
|
||
* "Jerk" specifies the minimum speed change that requires acceleration.
|
||
* When changing speed and direction, if the difference is less than the
|
||
* value set here, it may happen instantaneously.
|
||
*/
|
||
#define DEFAULT_XJERK 20.0
|
||
#define DEFAULT_YJERK 20.0
|
||
#define DEFAULT_ZJERK 20.0 // Must be same as XY for delta
|
||
#define DEFAULT_EJERK 5.0
|
||
|
||
|
||
/**
|
||
* ===========================================================================
|
||
* ============================= Z Probe Options =============================
|
||
* ===========================================================================
|
||
* @section probes
|
||
*
|
||
*
|
||
* Probe Type
|
||
* Probes are sensors/switches that are activated / deactivated before/after use.
|
||
*
|
||
* Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
|
||
* You must activate one of these to use Auto Bed Leveling below.
|
||
*
|
||
* Use M851 to set the Z probe vertical offset from the nozzle. Store with M500.
|
||
*/
|
||
|
||
/**
|
||
* The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe.
|
||
* Use G29 repeatedly, adjusting the Z height at each point with movement commands
|
||
* or (with LCD_BED_LEVELING) the LCD controller.
|
||
*/
|
||
//#define PROBE_MANUALLY
|
||
|
||
/**
|
||
* A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
|
||
* For example an inductive probe, or a setup that uses the nozzle to probe.
|
||
* An inductive probe must be deactivated to go below
|
||
* its trigger-point if hardware endstops are active.
|
||
*/
|
||
//#define FIX_MOUNTED_PROBE
|
||
|
||
/**
|
||
* Z Servo Probe, such as an endstop switch on a rotating arm.
|
||
* NUM_SERVOS also needs to be set. This is found later in this file. Set it to
|
||
* 1 + the number of other servos in your system.
|
||
*/
|
||
//#define Z_ENDSTOP_SERVO_NR 0 // Defaults to SERVO 0 connector.
|
||
//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles
|
||
|
||
/**
|
||
* The BLTouch probe emulates a servo probe.
|
||
* If using a BLTouch then NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES
|
||
* are setup for you in the background and you shouldn't need to set/modify/enable them
|
||
* with the possible exception of Z_ENDSTOP_SERVO_NR.
|
||
*/
|
||
//#define BLTOUCH
|
||
//#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed
|
||
|
||
/**
|
||
* BLTouch WARNING - ONLY APPLIES TO VERSIONS OF MARLIN BEFORE 15 FEB 2017
|
||
* Unless using interrupt endstops, there is a MINIMUM feedrate for Marlin to reliably
|
||
* sense the BLTouch. If the feedrate is too slow then G28 & G29 can sometimes result
|
||
* in the print head being driven into the bed until manual intervention.
|
||
* The minimum feedrate calculation is:
|
||
*
|
||
* feedrate minimum = 24000 / DEFAULT_AXIS_STEPS_PER_UNIT
|
||
* where feedrate is in "mm/minute" or "inches/minute" depending on the units used
|
||
* in DEFAULT_AXIS_STEPS_PER_UNIT
|
||
*
|
||
* This applies to the HOMING_FEEDRATE_Z and Z_PROBE_SPEED_FAST. If PROBE_DOUBLE_TOUCH
|
||
* is enabled then it also applies to Z_PROBE_SPEED_SLOW.
|
||
*/
|
||
|
||
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
|
||
//#define SOLENOID_PROBE
|
||
|
||
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
||
//#define Z_PROBE_SLED
|
||
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
||
|
||
/**
|
||
* Z Probe to nozzle (X,Y) offset, relative to (0, 0).
|
||
* X and Y offsets must be integers.
|
||
*
|
||
* In the following example the X and Y offsets are both positive:
|
||
* #define X_PROBE_OFFSET_FROM_EXTRUDER 10
|
||
* #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
|
||
*
|
||
* +-- BACK ---+
|
||
* | |
|
||
* L | (+) P | R <-- probe (20,20)
|
||
* E | | I
|
||
* F | (-) N (+) | G <-- nozzle (10,10)
|
||
* T | | H
|
||
* | (-) | T
|
||
* | |
|
||
* O-- FRONT --+
|
||
* (0,0)
|
||
*/
|
||
#define X_PROBE_OFFSET_FROM_EXTRUDER 0 // X offset: -left +right [of the nozzle]
|
||
#define Y_PROBE_OFFSET_FROM_EXTRUDER -10 // Y offset: -front +behind [the nozzle]
|
||
#define Z_PROBE_OFFSET_FROM_EXTRUDER -3.5 // Z offset: -below +above [the nozzle]
|
||
|
||
// X and Y axis travel speed (mm/m) between probes
|
||
#define XY_PROBE_SPEED 4000
|
||
|
||
// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH)
|
||
#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
|
||
|
||
// Speed for the "accurate" probe of each point
|
||
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
|
||
|
||
// Use double touch for probing
|
||
//#define PROBE_DOUBLE_TOUCH
|
||
|
||
/**
|
||
* Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
|
||
* Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
|
||
*/
|
||
//#define Z_PROBE_ALLEN_KEY
|
||
|
||
#if ENABLED(Z_PROBE_ALLEN_KEY)
|
||
// 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
|
||
// if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
|
||
|
||
#define Z_PROBE_ALLEN_KEY_DEPLOY_1_X 30.0
|
||
#define Z_PROBE_ALLEN_KEY_DEPLOY_1_Y DELTA_PRINTABLE_RADIUS
|
||
#define Z_PROBE_ALLEN_KEY_DEPLOY_1_Z 100.0
|
||
#define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_SPEED
|
||
|
||
#define Z_PROBE_ALLEN_KEY_DEPLOY_2_X 0.0
|
||
#define Z_PROBE_ALLEN_KEY_DEPLOY_2_Y DELTA_PRINTABLE_RADIUS
|
||
#define Z_PROBE_ALLEN_KEY_DEPLOY_2_Z 100.0
|
||
#define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_SPEED)/10
|
||
|
||
#define Z_PROBE_ALLEN_KEY_DEPLOY_3_X Z_PROBE_ALLEN_KEY_DEPLOY_2_X * 0.75
|
||
#define Z_PROBE_ALLEN_KEY_DEPLOY_3_Y Z_PROBE_ALLEN_KEY_DEPLOY_2_Y * 0.75
|
||
#define Z_PROBE_ALLEN_KEY_DEPLOY_3_Z Z_PROBE_ALLEN_KEY_DEPLOY_2_Z
|
||
#define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_SPEED
|
||
|
||
#define Z_PROBE_ALLEN_KEY_STOW_1_X -64.0 // Move the probe into position
|
||
#define Z_PROBE_ALLEN_KEY_STOW_1_Y 56.0
|
||
#define Z_PROBE_ALLEN_KEY_STOW_1_Z 23.0
|
||
#define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_SPEED
|
||
|
||
#define Z_PROBE_ALLEN_KEY_STOW_2_X -64.0 // Push it down
|
||
#define Z_PROBE_ALLEN_KEY_STOW_2_Y 56.0
|
||
#define Z_PROBE_ALLEN_KEY_STOW_2_Z 3.0
|
||
#define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_SPEED)/10
|
||
|
||
#define Z_PROBE_ALLEN_KEY_STOW_3_X -64.0 // Move it up to clear
|
||
#define Z_PROBE_ALLEN_KEY_STOW_3_Y 56.0
|
||
#define Z_PROBE_ALLEN_KEY_STOW_3_Z 50.0
|
||
#define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_SPEED
|
||
|
||
#define Z_PROBE_ALLEN_KEY_STOW_4_X 0.0
|
||
#define Z_PROBE_ALLEN_KEY_STOW_4_Y 0.0
|
||
#define Z_PROBE_ALLEN_KEY_STOW_4_Z Z_PROBE_ALLEN_KEY_STOW_3_Z
|
||
#define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_SPEED
|
||
|
||
#endif // Z_PROBE_ALLEN_KEY
|
||
|
||
/**
|
||
*
|
||
* *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
|
||
*
|
||
* - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
|
||
* - Use 5V for powered (usu. inductive) sensors.
|
||
* - Otherwise connect:
|
||
* - normally-closed switches to GND and D32.
|
||
* - normally-open switches to 5V and D32.
|
||
*
|
||
* Normally-closed switches are advised and are the default.
|
||
*
|
||
*
|
||
* PIN OPTIONS\SETUP FOR Z PROBES
|
||
*
|
||
*
|
||
* WARNING:
|
||
* Setting the wrong pin may have unexpected and potentially disastrous consequences.
|
||
* Use with caution and do your homework.
|
||
*
|
||
*
|
||
* All Z PROBE pin options are configured by defining (or not defining)
|
||
* the following five items:
|
||
* Z_MIN_PROBE_ENDSTOP – defined below
|
||
* Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN – defined below
|
||
* Z_MIN_PIN - defined in the pins_YOUR_BOARD.h file
|
||
* Z_MIN_PROBE_PIN - defined in the pins_YOUR_BOARD.h file
|
||
*
|
||
* If you're using a probe then you need to tell Marlin which pin to use as
|
||
* the Z MIN ENDSTOP. Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN determines if the
|
||
* Z_MIN_PIN or if the Z_MIN_PROBE_PIN is used.
|
||
*
|
||
* The pin selected for the probe is ONLY checked during probing operations.
|
||
* If you want to use the Z_MIN_PIN as an endstop AND you want to have a Z PROBE
|
||
* then you’ll need to use the Z_MIN_PROBE_PIN option.
|
||
*
|
||
* Z_MIN_PROBE_ENDSTOP also needs to be enabled if you want to use Z_MIN_PROBE_PIN.
|
||
*
|
||
* The settings needed to use the Z_MIN_PROBE_PIN are:
|
||
* 1. select the type of probe you're using
|
||
* 2. define Z_MIN_PROBE_PIN in your pins_YOUR_BOARD.h file
|
||
* 3. disable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||
* 4. enable Z_MIN_PROBE_ENDSTOP
|
||
* NOTE – if Z_MIN_PIN is defined then it’ll be checked during all moves in the
|
||
* negative Z direction.
|
||
*
|
||
* The settings needed to use the Z_MIN_PIN are:
|
||
* 1. select the type of probe you're using
|
||
* 2. enable Z_MIN _PIN in your pins_YOUR_BOARD.h file
|
||
* 3. enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||
* 4. disable Z_MIN_PROBE_ENDSTOP
|
||
* NOTES – if Z_MIN_PROBE_PIN is defined in the pins_YOUR_BOARD.h file then it’ll be
|
||
* ignored by Marlin
|
||
*/
|
||
|
||
#define Z_MIN_PROBE_ENDSTOP
|
||
//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||
|
||
|
||
// Enable Z Probe Repeatability test to see how accurate your probe is
|
||
//#define Z_MIN_PROBE_REPEATABILITY_TEST
|
||
|
||
/**
|
||
* Z probes require clearance when deploying, stowing, and moving between
|
||
* probe points to avoid hitting the bed and other hardware.
|
||
* Servo-mounted probes require extra space for the arm to rotate.
|
||
* Inductive probes need space to keep from triggering early.
|
||
*
|
||
* Use these settings to specify the distance (mm) to raise the probe (or
|
||
* lower the bed). The values set here apply over and above any (negative)
|
||
* probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
|
||
* Only integer values >= 1 are valid here.
|
||
*
|
||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||
*/
|
||
#define Z_CLEARANCE_DEPLOY_PROBE 15 // Z Clearance for Deploy/Stow
|
||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||
|
||
// For M851 give a range for adjusting the Z probe offset
|
||
#define Z_PROBE_OFFSET_RANGE_MIN -20
|
||
#define Z_PROBE_OFFSET_RANGE_MAX 20
|
||
|
||
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
||
// :{ 0:'Low', 1:'High' }
|
||
#define X_ENABLE_ON 0
|
||
#define Y_ENABLE_ON 0
|
||
#define Z_ENABLE_ON 0
|
||
#define E_ENABLE_ON 0 // For all extruders
|
||
|
||
// Disables axis stepper immediately when it's not being used.
|
||
// WARNING: When motors turn off there is a chance of losing position accuracy!
|
||
#define DISABLE_X false
|
||
#define DISABLE_Y false
|
||
#define DISABLE_Z false
|
||
// Warn on display about possibly reduced accuracy
|
||
//#define DISABLE_REDUCED_ACCURACY_WARNING
|
||
|
||
// @section extruder
|
||
|
||
#define DISABLE_E false // For all extruders
|
||
#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
|
||
|
||
// @section machine
|
||
|
||
// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
|
||
#define INVERT_X_DIR false // DELTA does not invert
|
||
#define INVERT_Y_DIR false
|
||
#define INVERT_Z_DIR false
|
||
|
||
// Enable this option for Toshiba stepper drivers
|
||
//#define CONFIG_STEPPERS_TOSHIBA
|
||
|
||
// @section extruder
|
||
|
||
// For direct drive extruder v9 set to true, for geared extruder set to false.
|
||
#define INVERT_E0_DIR false
|
||
#define INVERT_E1_DIR false
|
||
#define INVERT_E2_DIR false
|
||
#define INVERT_E3_DIR false
|
||
#define INVERT_E4_DIR false
|
||
|
||
// @section homing
|
||
|
||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||
|
||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||
// :[-1,1]
|
||
#define X_HOME_DIR 1 // deltas always home to max
|
||
#define Y_HOME_DIR 1
|
||
#define Z_HOME_DIR 1
|
||
|
||
// @section machine
|
||
|
||
// Travel limits after homing (units are in mm)
|
||
#define X_MIN_POS -(DELTA_PRINTABLE_RADIUS)
|
||
#define Y_MIN_POS -(DELTA_PRINTABLE_RADIUS)
|
||
#define Z_MIN_POS 0
|
||
#define X_MAX_POS DELTA_PRINTABLE_RADIUS
|
||
#define Y_MAX_POS DELTA_PRINTABLE_RADIUS
|
||
#define Z_MAX_POS MANUAL_Z_HOME_POS
|
||
|
||
// If enabled, axes won't move below MIN_POS in response to movement commands.
|
||
#define MIN_SOFTWARE_ENDSTOPS
|
||
// If enabled, axes won't move above MAX_POS in response to movement commands.
|
||
#define MAX_SOFTWARE_ENDSTOPS
|
||
|
||
/**
|
||
* Filament Runout Sensor
|
||
* A mechanical or opto endstop is used to check for the presence of filament.
|
||
*
|
||
* RAMPS-based boards use SERVO3_PIN.
|
||
* For other boards you may need to define FIL_RUNOUT_PIN.
|
||
* By default the firmware assumes HIGH = has filament, LOW = ran out
|
||
*/
|
||
//#define FILAMENT_RUNOUT_SENSOR
|
||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||
#define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor.
|
||
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
|
||
#define FILAMENT_RUNOUT_SCRIPT "M600"
|
||
#endif
|
||
|
||
//===========================================================================
|
||
//=============================== Bed Leveling ==============================
|
||
//===========================================================================
|
||
// @section bedlevel
|
||
|
||
/**
|
||
* Choose one of the options below to enable G29 Bed Leveling. The parameters
|
||
* and behavior of G29 will change depending on your selection.
|
||
*
|
||
* If using a Probe for Z Homing, enable Z_SAFE_HOMING also!
|
||
*
|
||
* - AUTO_BED_LEVELING_3POINT
|
||
* Probe 3 arbitrary points on the bed (that aren't collinear)
|
||
* You specify the XY coordinates of all 3 points.
|
||
* The result is a single tilted plane. Best for a flat bed.
|
||
*
|
||
* - AUTO_BED_LEVELING_LINEAR
|
||
* Probe several points in a grid.
|
||
* You specify the rectangle and the density of sample points.
|
||
* The result is a single tilted plane. Best for a flat bed.
|
||
*
|
||
* - AUTO_BED_LEVELING_BILINEAR
|
||
* Probe several points in a grid.
|
||
* You specify the rectangle and the density of sample points.
|
||
* The result is a mesh, best for large or uneven beds.
|
||
*
|
||
* - AUTO_BED_LEVELING_UBL (Unified Bed Leveling)
|
||
* A comprehensive bed leveling system combining the features and benefits
|
||
* of other systems. UBL also includes integrated Mesh Generation, Mesh
|
||
* Validation and Mesh Editing systems. Currently, UBL is only checked out
|
||
* for Cartesian Printers. That said, it was primarily designed to correct
|
||
* poor quality Delta Printers. If you feel adventurous and have a Delta,
|
||
* please post an issue if something doesn't work correctly. Initially,
|
||
* you will need to set a reduced bed size so you have a rectangular area
|
||
* to test on.
|
||
*
|
||
* - MESH_BED_LEVELING
|
||
* Probe a grid manually
|
||
* The result is a mesh, suitable for large or uneven beds. (See BILINEAR.)
|
||
* For machines without a probe, Mesh Bed Leveling provides a method to perform
|
||
* leveling in steps so you can manually adjust the Z height at each grid-point.
|
||
* With an LCD controller the process is guided step-by-step.
|
||
*/
|
||
//#define AUTO_BED_LEVELING_3POINT
|
||
//#define AUTO_BED_LEVELING_LINEAR
|
||
//#define AUTO_BED_LEVELING_BILINEAR
|
||
//#define AUTO_BED_LEVELING_UBL
|
||
//#define MESH_BED_LEVELING
|
||
|
||
/**
|
||
* Enable detailed logging of G28, G29, M48, etc.
|
||
* Turn on with the command 'M111 S32'.
|
||
* NOTE: Requires a lot of PROGMEM!
|
||
*/
|
||
//#define DEBUG_LEVELING_FEATURE
|
||
|
||
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
|
||
// Gradually reduce leveling correction until a set height is reached,
|
||
// at which point movement will be level to the machine's XY plane.
|
||
// The height can be set with M420 Z<height>
|
||
//#define ENABLE_LEVELING_FADE_HEIGHT
|
||
#endif
|
||
|
||
#if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR)
|
||
|
||
// Set the number of grid points per dimension.
|
||
// Works best with 5 or more points in each dimension.
|
||
#define GRID_MAX_POINTS_X 9
|
||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||
|
||
// Set the boundaries for probing (where the probe can reach).
|
||
#define DELTA_PROBEABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
|
||
#define LEFT_PROBE_BED_POSITION -(DELTA_PROBEABLE_RADIUS)
|
||
#define RIGHT_PROBE_BED_POSITION DELTA_PROBEABLE_RADIUS
|
||
#define FRONT_PROBE_BED_POSITION -(DELTA_PROBEABLE_RADIUS)
|
||
#define BACK_PROBE_BED_POSITION DELTA_PROBEABLE_RADIUS
|
||
|
||
// The Z probe minimum outer margin (to validate G29 parameters).
|
||
#define MIN_PROBE_EDGE 10
|
||
|
||
// Probe along the Y axis, advancing X after each column
|
||
//#define PROBE_Y_FIRST
|
||
|
||
#if ENABLED(AUTO_BED_LEVELING_BILINEAR)
|
||
//
|
||
// Experimental Subdivision of the grid by Catmull-Rom method.
|
||
// Synthesizes intermediate points to produce a more detailed mesh.
|
||
//
|
||
//#define ABL_BILINEAR_SUBDIVISION
|
||
#if ENABLED(ABL_BILINEAR_SUBDIVISION)
|
||
// Number of subdivisions between probe points
|
||
#define BILINEAR_SUBDIVISIONS 3
|
||
#endif
|
||
|
||
#endif
|
||
|
||
#elif ENABLED(AUTO_BED_LEVELING_3POINT)
|
||
|
||
// 3 arbitrary points to probe.
|
||
// A simple cross-product is used to estimate the plane of the bed.
|
||
#define ABL_PROBE_PT_1_X 15
|
||
#define ABL_PROBE_PT_1_Y 180
|
||
#define ABL_PROBE_PT_2_X 15
|
||
#define ABL_PROBE_PT_2_Y 20
|
||
#define ABL_PROBE_PT_3_X 170
|
||
#define ABL_PROBE_PT_3_Y 20
|
||
|
||
#elif ENABLED(AUTO_BED_LEVELING_UBL)
|
||
|
||
//===========================================================================
|
||
//========================= Unified Bed Leveling ============================
|
||
//===========================================================================
|
||
|
||
#define UBL_MESH_INSET 1 // Mesh inset margin on print area
|
||
#define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited.
|
||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||
#define UBL_PROBE_PT_1_X 39 // These set the probe locations for when UBL does a 3-Point leveling
|
||
#define UBL_PROBE_PT_1_Y 180 // of the mesh.
|
||
#define UBL_PROBE_PT_2_X 39
|
||
#define UBL_PROBE_PT_2_Y 20
|
||
#define UBL_PROBE_PT_3_X 180
|
||
#define UBL_PROBE_PT_3_Y 20
|
||
//#define UBL_G26_MESH_EDITING // Enable G26 mesh editing
|
||
|
||
#elif ENABLED(MESH_BED_LEVELING)
|
||
|
||
//===========================================================================
|
||
//=================================== Mesh ==================================
|
||
//===========================================================================
|
||
|
||
#define MESH_INSET 10 // Mesh inset margin on print area
|
||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||
|
||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||
|
||
#endif // BED_LEVELING
|
||
|
||
/**
|
||
* Use the LCD controller for bed leveling
|
||
* Requires MESH_BED_LEVELING or PROBE_MANUALLY
|
||
*/
|
||
//#define LCD_BED_LEVELING
|
||
|
||
#if ENABLED(LCD_BED_LEVELING)
|
||
#define MBL_Z_STEP 0.025 // Step size while manually probing Z axis.
|
||
#define LCD_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
|
||
#endif
|
||
|
||
/**
|
||
* Commands to execute at the end of G29 probing.
|
||
* Useful to retract or move the Z probe out of the way.
|
||
*/
|
||
//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
|
||
|
||
|
||
// @section homing
|
||
|
||
// The center of the bed is at (X=0, Y=0)
|
||
#define BED_CENTER_AT_0_0
|
||
|
||
// Manually set the home position. Leave these undefined for automatic settings.
|
||
// For DELTA this is the top-center of the Cartesian print volume.
|
||
//#define MANUAL_X_HOME_POS 0
|
||
//#define MANUAL_Y_HOME_POS 0
|
||
#define MANUAL_Z_HOME_POS DELTA_HEIGHT // Distance between the nozzle to printbed after homing
|
||
|
||
// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
|
||
//
|
||
// With this feature enabled:
|
||
//
|
||
// - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
|
||
// - If stepper drivers time out, it will need X and Y homing again before Z homing.
|
||
// - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28).
|
||
// - Prevent Z homing when the Z probe is outside bed area.
|
||
//#define Z_SAFE_HOMING
|
||
|
||
#if ENABLED(Z_SAFE_HOMING)
|
||
#define Z_SAFE_HOMING_X_POINT ((X_MIN_POS + X_MAX_POS) / 2) // X point for Z homing when homing all axis (G28).
|
||
#define Z_SAFE_HOMING_Y_POINT ((Y_MIN_POS + Y_MAX_POS) / 2) // Y point for Z homing when homing all axis (G28).
|
||
#endif
|
||
|
||
// Delta only homes to Z
|
||
#define HOMING_FEEDRATE_Z (200*60)
|
||
|
||
//=============================================================================
|
||
//============================= Additional Features ===========================
|
||
//=============================================================================
|
||
|
||
// @section extras
|
||
|
||
//
|
||
// EEPROM
|
||
//
|
||
// The microcontroller can store settings in the EEPROM, e.g. max velocity...
|
||
// M500 - stores parameters in EEPROM
|
||
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
|
||
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
|
||
//define this to enable EEPROM support
|
||
//#define EEPROM_SETTINGS
|
||
|
||
#if ENABLED(EEPROM_SETTINGS)
|
||
// To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
|
||
#define EEPROM_CHITCHAT // Please keep turned on if you can.
|
||
#endif
|
||
|
||
//
|
||
// Host Keepalive
|
||
//
|
||
// When enabled Marlin will send a busy status message to the host
|
||
// every couple of seconds when it can't accept commands.
|
||
//
|
||
#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
|
||
#define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
|
||
|
||
//
|
||
// M100 Free Memory Watcher
|
||
//
|
||
//#define M100_FREE_MEMORY_WATCHER // uncomment to add the M100 Free Memory Watcher for debug purpose
|
||
|
||
//
|
||
// G20/G21 Inch mode support
|
||
//
|
||
//#define INCH_MODE_SUPPORT
|
||
|
||
//
|
||
// M149 Set temperature units support
|
||
//
|
||
//#define TEMPERATURE_UNITS_SUPPORT
|
||
|
||
// @section temperature
|
||
|
||
// Preheat Constants
|
||
#define PREHEAT_1_TEMP_HOTEND 180
|
||
#define PREHEAT_1_TEMP_BED 70
|
||
#define PREHEAT_1_FAN_SPEED 255 // Value from 0 to 255
|
||
|
||
#define PREHEAT_2_TEMP_HOTEND 240
|
||
#define PREHEAT_2_TEMP_BED 100
|
||
#define PREHEAT_2_FAN_SPEED 255 // Value from 0 to 255
|
||
|
||
//
|
||
// Nozzle Park -- EXPERIMENTAL
|
||
//
|
||
// When enabled allows the user to define a special XYZ position, inside the
|
||
// machine's topology, to park the nozzle when idle or when receiving the G27
|
||
// command.
|
||
//
|
||
// The "P" paramenter controls what is the action applied to the Z axis:
|
||
// P0: (Default) If current Z-pos is lower than Z-park then the nozzle will
|
||
// be raised to reach Z-park height.
|
||
//
|
||
// P1: No matter the current Z-pos, the nozzle will be raised/lowered to
|
||
// reach Z-park height.
|
||
//
|
||
// P2: The nozzle height will be raised by Z-park amount but never going over
|
||
// the machine's limit of Z_MAX_POS.
|
||
//
|
||
//#define NOZZLE_PARK_FEATURE
|
||
|
||
#if ENABLED(NOZZLE_PARK_FEATURE)
|
||
// Specify a park position as { X, Y, Z }
|
||
#define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
|
||
#endif
|
||
|
||
//
|
||
// Clean Nozzle Feature -- EXPERIMENTAL
|
||
//
|
||
// When enabled allows the user to send G12 to start the nozzle cleaning
|
||
// process, the G-Code accepts two parameters:
|
||
// "P" for pattern selection
|
||
// "S" for defining the number of strokes/repetitions
|
||
//
|
||
// Available list of patterns:
|
||
// P0: This is the default pattern, this process requires a sponge type
|
||
// material at a fixed bed location. S defines "strokes" i.e.
|
||
// back-and-forth movements between the starting and end points.
|
||
//
|
||
// P1: This starts a zig-zag pattern between (X0, Y0) and (X1, Y1), "T"
|
||
// defines the number of zig-zag triangles to be done. "S" defines the
|
||
// number of strokes aka one back-and-forth movement. Zig-zags will
|
||
// be performed in whichever dimension is smallest. As an example,
|
||
// sending "G12 P1 S1 T3" will execute:
|
||
//
|
||
// --
|
||
// | (X0, Y1) | /\ /\ /\ | (X1, Y1)
|
||
// | | / \ / \ / \ |
|
||
// A | | / \ / \ / \ |
|
||
// | | / \ / \ / \ |
|
||
// | (X0, Y0) | / \/ \/ \ | (X1, Y0)
|
||
// -- +--------------------------------+
|
||
// |________|_________|_________|
|
||
// T1 T2 T3
|
||
//
|
||
// P2: This starts a circular pattern with circle with middle in
|
||
// NOZZLE_CLEAN_CIRCLE_MIDDLE radius of R and stroke count of S.
|
||
// Before starting the circle nozzle goes to NOZZLE_CLEAN_START_POINT.
|
||
//
|
||
// Caveats: End point Z should use the same value as Start point Z.
|
||
//
|
||
// Attention: This is an EXPERIMENTAL feature, in the future the G-code arguments
|
||
// may change to add new functionality like different wipe patterns.
|
||
//
|
||
//#define NOZZLE_CLEAN_FEATURE
|
||
|
||
#if ENABLED(NOZZLE_CLEAN_FEATURE)
|
||
// Default number of pattern repetitions
|
||
#define NOZZLE_CLEAN_STROKES 12
|
||
|
||
// Default number of triangles
|
||
#define NOZZLE_CLEAN_TRIANGLES 3
|
||
|
||
// Specify positions as { X, Y, Z }
|
||
#define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
|
||
#define NOZZLE_CLEAN_END_POINT {100, 60, (Z_MIN_POS + 1)}
|
||
|
||
// Circular pattern radius
|
||
#define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
|
||
// Circular pattern circle fragments number
|
||
#define NOZZLE_CLEAN_CIRCLE_FN 10
|
||
// Middle point of circle
|
||
#define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
|
||
|
||
// Moves the nozzle to the initial position
|
||
#define NOZZLE_CLEAN_GOBACK
|
||
#endif
|
||
|
||
//
|
||
// Print job timer
|
||
//
|
||
// Enable this option to automatically start and stop the
|
||
// print job timer when M104/M109/M190 commands are received.
|
||
// M104 (extruder without wait) - high temp = none, low temp = stop timer
|
||
// M109 (extruder with wait) - high temp = start timer, low temp = stop timer
|
||
// M190 (bed with wait) - high temp = start timer, low temp = none
|
||
//
|
||
// In all cases the timer can be started and stopped using
|
||
// the following commands:
|
||
//
|
||
// - M75 - Start the print job timer
|
||
// - M76 - Pause the print job timer
|
||
// - M77 - Stop the print job timer
|
||
#define PRINTJOB_TIMER_AUTOSTART
|
||
|
||
//
|
||
// Print Counter
|
||
//
|
||
// When enabled Marlin will keep track of some print statistical data such as:
|
||
// - Total print jobs
|
||
// - Total successful print jobs
|
||
// - Total failed print jobs
|
||
// - Total time printing
|
||
//
|
||
// This information can be viewed by the M78 command.
|
||
//#define PRINTCOUNTER
|
||
|
||
//=============================================================================
|
||
//============================= LCD and SD support ============================
|
||
//=============================================================================
|
||
|
||
// @section lcd
|
||
|
||
//
|
||
// LCD LANGUAGE
|
||
//
|
||
// Here you may choose the language used by Marlin on the LCD menus, the following
|
||
// list of languages are available:
|
||
// en, an, bg, ca, cn, cz, de, el, el-gr, es, eu, fi, fr, gl, hr, it,
|
||
// kana, kana_utf8, nl, pl, pt, pt_utf8, pt-br, pt-br_utf8, ru, tr, uk, test
|
||
//
|
||
// :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'tr':'Turkish', 'uk':'Ukrainian', 'test':'TEST' }
|
||
//
|
||
#define LCD_LANGUAGE en
|
||
|
||
//
|
||
// LCD Character Set
|
||
//
|
||
// Note: This option is NOT applicable to Graphical Displays.
|
||
//
|
||
// All character-based LCD's provide ASCII plus one of these
|
||
// language extensions:
|
||
//
|
||
// - JAPANESE ... the most common
|
||
// - WESTERN ... with more accented characters
|
||
// - CYRILLIC ... for the Russian language
|
||
//
|
||
// To determine the language extension installed on your controller:
|
||
//
|
||
// - Compile and upload with LCD_LANGUAGE set to 'test'
|
||
// - Click the controller to view the LCD menu
|
||
// - The LCD will display Japanese, Western, or Cyrillic text
|
||
//
|
||
// See https://github.com/MarlinFirmware/Marlin/wiki/LCD-Language
|
||
//
|
||
// :['JAPANESE', 'WESTERN', 'CYRILLIC']
|
||
//
|
||
#define DISPLAY_CHARSET_HD44780 JAPANESE
|
||
|
||
//
|
||
// LCD TYPE
|
||
//
|
||
// You may choose ULTRA_LCD if you have character based LCD with 16x2, 16x4, 20x2,
|
||
// 20x4 char/lines or DOGLCD for the full graphics display with 128x64 pixels
|
||
// (ST7565R family). (This option will be set automatically for certain displays.)
|
||
//
|
||
// IMPORTANT NOTE: The U8glib library is required for Full Graphic Display!
|
||
// https://github.com/olikraus/U8glib_Arduino
|
||
//
|
||
//#define ULTRA_LCD // Character based
|
||
//#define DOGLCD // Full graphics display
|
||
|
||
//
|
||
// SD CARD
|
||
//
|
||
// SD Card support is disabled by default. If your controller has an SD slot,
|
||
// you must uncomment the following option or it won't work.
|
||
//
|
||
//#define SDSUPPORT
|
||
|
||
//
|
||
// SD CARD: SPI SPEED
|
||
//
|
||
// Uncomment ONE of the following items to use a slower SPI transfer
|
||
// speed. This is usually required if you're getting volume init errors.
|
||
//
|
||
//#define SPI_SPEED SPI_HALF_SPEED
|
||
//#define SPI_SPEED SPI_QUARTER_SPEED
|
||
//#define SPI_SPEED SPI_EIGHTH_SPEED
|
||
|
||
//
|
||
// SD CARD: ENABLE CRC
|
||
//
|
||
// Use CRC checks and retries on the SD communication.
|
||
//
|
||
//#define SD_CHECK_AND_RETRY
|
||
|
||
//
|
||
// ENCODER SETTINGS
|
||
//
|
||
// This option overrides the default number of encoder pulses needed to
|
||
// produce one step. Should be increased for high-resolution encoders.
|
||
//
|
||
//#define ENCODER_PULSES_PER_STEP 1
|
||
|
||
//
|
||
// Use this option to override the number of step signals required to
|
||
// move between next/prev menu items.
|
||
//
|
||
//#define ENCODER_STEPS_PER_MENU_ITEM 5
|
||
|
||
/**
|
||
* Encoder Direction Options
|
||
*
|
||
* Test your encoder's behavior first with both options disabled.
|
||
*
|
||
* Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
|
||
* Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION.
|
||
* Reversed Value Editing only? Enable BOTH options.
|
||
*/
|
||
|
||
//
|
||
// This option reverses the encoder direction everywhere
|
||
//
|
||
// Set this option if CLOCKWISE causes values to DECREASE
|
||
//
|
||
//#define REVERSE_ENCODER_DIRECTION
|
||
|
||
//
|
||
// This option reverses the encoder direction for navigating LCD menus.
|
||
//
|
||
// If CLOCKWISE normally moves DOWN this makes it go UP.
|
||
// If CLOCKWISE normally moves UP this makes it go DOWN.
|
||
//
|
||
//#define REVERSE_MENU_DIRECTION
|
||
|
||
//
|
||
// Individual Axis Homing
|
||
//
|
||
// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
|
||
//
|
||
//#define INDIVIDUAL_AXIS_HOMING_MENU
|
||
|
||
//
|
||
// SPEAKER/BUZZER
|
||
//
|
||
// If you have a speaker that can produce tones, enable it here.
|
||
// By default Marlin assumes you have a buzzer with a fixed frequency.
|
||
//
|
||
//#define SPEAKER
|
||
|
||
//
|
||
// The duration and frequency for the UI feedback sound.
|
||
// Set these to 0 to disable audio feedback in the LCD menus.
|
||
//
|
||
// Note: Test audio output with the G-Code:
|
||
// M300 S<frequency Hz> P<duration ms>
|
||
//
|
||
//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
|
||
//#define LCD_FEEDBACK_FREQUENCY_HZ 1000
|
||
|
||
//
|
||
// CONTROLLER TYPE: Standard
|
||
//
|
||
// Marlin supports a wide variety of controllers.
|
||
// Enable one of the following options to specify your controller.
|
||
//
|
||
|
||
//
|
||
// ULTIMAKER Controller.
|
||
//
|
||
//#define ULTIMAKERCONTROLLER
|
||
|
||
//
|
||
// ULTIPANEL as seen on Thingiverse.
|
||
//
|
||
//#define ULTIPANEL
|
||
|
||
//
|
||
// Cartesio UI
|
||
// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
|
||
//
|
||
//#define CARTESIO_UI
|
||
|
||
//
|
||
// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
|
||
// http://reprap.org/wiki/PanelOne
|
||
//
|
||
//#define PANEL_ONE
|
||
|
||
//
|
||
// MaKr3d Makr-Panel with graphic controller and SD support.
|
||
// http://reprap.org/wiki/MaKr3d_MaKrPanel
|
||
//
|
||
//#define MAKRPANEL
|
||
|
||
//
|
||
// ReprapWorld Graphical LCD
|
||
// https://reprapworld.com/?products_details&products_id/1218
|
||
//
|
||
//#define REPRAPWORLD_GRAPHICAL_LCD
|
||
|
||
//
|
||
// Activate one of these if you have a Panucatt Devices
|
||
// Viki 2.0 or mini Viki with Graphic LCD
|
||
// http://panucatt.com
|
||
//
|
||
//#define VIKI2
|
||
//#define miniVIKI
|
||
|
||
//
|
||
// Adafruit ST7565 Full Graphic Controller.
|
||
// https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
|
||
//
|
||
//#define ELB_FULL_GRAPHIC_CONTROLLER
|
||
|
||
//
|
||
// RepRapDiscount Smart Controller.
|
||
// http://reprap.org/wiki/RepRapDiscount_Smart_Controller
|
||
//
|
||
// Note: Usually sold with a white PCB.
|
||
//
|
||
//#define REPRAP_DISCOUNT_SMART_CONTROLLER
|
||
|
||
//
|
||
// GADGETS3D G3D LCD/SD Controller
|
||
// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
|
||
//
|
||
// Note: Usually sold with a blue PCB.
|
||
//
|
||
//#define G3D_PANEL
|
||
|
||
//
|
||
// RepRapDiscount FULL GRAPHIC Smart Controller
|
||
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||
//
|
||
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||
|
||
//
|
||
// MakerLab Mini Panel with graphic
|
||
// controller and SD support - http://reprap.org/wiki/Mini_panel
|
||
//
|
||
//#define MINIPANEL
|
||
|
||
//
|
||
// RepRapWorld REPRAPWORLD_KEYPAD v1.1
|
||
// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
|
||
//
|
||
// REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key
|
||
// is pressed, a value of 10.0 means 10mm per click.
|
||
//
|
||
//#define REPRAPWORLD_KEYPAD
|
||
//#define REPRAPWORLD_KEYPAD_MOVE_STEP 1.0
|
||
|
||
//
|
||
// RigidBot Panel V1.0
|
||
// http://www.inventapart.com/
|
||
//
|
||
//#define RIGIDBOT_PANEL
|
||
|
||
//
|
||
// BQ LCD Smart Controller shipped by
|
||
// default with the BQ Hephestos 2 and Witbox 2.
|
||
//
|
||
//#define BQ_LCD_SMART_CONTROLLER
|
||
|
||
//
|
||
// CONTROLLER TYPE: I2C
|
||
//
|
||
// Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
|
||
// library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
|
||
//
|
||
|
||
//
|
||
// Elefu RA Board Control Panel
|
||
// http://www.elefu.com/index.php?route=product/product&product_id=53
|
||
//
|
||
//#define RA_CONTROL_PANEL
|
||
|
||
//
|
||
// Sainsmart YW Robot (LCM1602) LCD Display
|
||
//
|
||
//#define LCD_I2C_SAINSMART_YWROBOT
|
||
|
||
//
|
||
// Generic LCM1602 LCD adapter
|
||
//
|
||
//#define LCM1602
|
||
|
||
//
|
||
// PANELOLU2 LCD with status LEDs,
|
||
// separate encoder and click inputs.
|
||
//
|
||
// Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
|
||
// For more info: https://github.com/lincomatic/LiquidTWI2
|
||
//
|
||
// Note: The PANELOLU2 encoder click input can either be directly connected to
|
||
// a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
|
||
//
|
||
//#define LCD_I2C_PANELOLU2
|
||
|
||
//
|
||
// Panucatt VIKI LCD with status LEDs,
|
||
// integrated click & L/R/U/D buttons, separate encoder inputs.
|
||
//
|
||
//#define LCD_I2C_VIKI
|
||
|
||
//
|
||
// SSD1306 OLED full graphics generic display
|
||
//
|
||
//#define U8GLIB_SSD1306
|
||
|
||
//
|
||
// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
|
||
//
|
||
//#define SAV_3DGLCD
|
||
#if ENABLED(SAV_3DGLCD)
|
||
//#define U8GLIB_SSD1306
|
||
#define U8GLIB_SH1106
|
||
#endif
|
||
|
||
//
|
||
// CONTROLLER TYPE: Shift register panels
|
||
//
|
||
// 2 wire Non-latching LCD SR from https://goo.gl/aJJ4sH
|
||
// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
|
||
//
|
||
//#define SAV_3DLCD
|
||
|
||
//
|
||
// TinyBoy2 128x64 OLED / Encoder Panel
|
||
//
|
||
//#define OLED_PANEL_TINYBOY2
|
||
|
||
//=============================================================================
|
||
//=============================== Extra Features ==============================
|
||
//=============================================================================
|
||
|
||
// @section extras
|
||
|
||
// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
|
||
//#define FAST_PWM_FAN
|
||
|
||
// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
|
||
// which is not as annoying as with the hardware PWM. On the other hand, if this frequency
|
||
// is too low, you should also increment SOFT_PWM_SCALE.
|
||
//#define FAN_SOFT_PWM
|
||
|
||
// Incrementing this by 1 will double the software PWM frequency,
|
||
// affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
|
||
// However, control resolution will be halved for each increment;
|
||
// at zero value, there are 128 effective control positions.
|
||
#define SOFT_PWM_SCALE 0
|
||
|
||
// If SOFT_PWM_SCALE is set to a value higher than 0, dithering can
|
||
// be used to mitigate the associated resolution loss. If enabled,
|
||
// some of the PWM cycles are stretched so on average the desired
|
||
// duty cycle is attained.
|
||
//#define SOFT_PWM_DITHER
|
||
|
||
// Temperature status LEDs that display the hotend and bed temperature.
|
||
// If all hotends, bed temperature, and target temperature are under 54C
|
||
// then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis)
|
||
//#define TEMP_STAT_LEDS
|
||
|
||
// M240 Triggers a camera by emulating a Canon RC-1 Remote
|
||
// Data from: http://www.doc-diy.net/photo/rc-1_hacked/
|
||
//#define PHOTOGRAPH_PIN 23
|
||
|
||
// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
|
||
//#define SF_ARC_FIX
|
||
|
||
// Support for the BariCUDA Paste Extruder.
|
||
//#define BARICUDA
|
||
|
||
//define BlinkM/CyzRgb Support
|
||
//#define BLINKM
|
||
|
||
/**
|
||
* RGB LED / LED Strip Control
|
||
*
|
||
* Enable support for an RGB LED connected to 5V digital pins, or
|
||
* an RGB Strip connected to MOSFETs controlled by digital pins.
|
||
*
|
||
* Adds the M150 command to set the LED (or LED strip) color.
|
||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||
* luminance values can be set from 0 to 255.
|
||
*
|
||
* *** CAUTION ***
|
||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||
* as the Arduino cannot handle the current the LEDs will require.
|
||
* Failure to follow this precaution can destroy your Arduino!
|
||
* *** CAUTION ***
|
||
*
|
||
*/
|
||
//#define RGB_LED
|
||
//#define RGBW_LED
|
||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||
#define RGB_LED_R_PIN 34
|
||
#define RGB_LED_G_PIN 43
|
||
#define RGB_LED_B_PIN 35
|
||
#define RGB_LED_W_PIN -1
|
||
#endif
|
||
|
||
/**
|
||
* Printer Event LEDs
|
||
*
|
||
* During printing, the LEDs will reflect the printer status:
|
||
*
|
||
* - Gradually change from blue to violet as the heated bed gets to target temp
|
||
* - Gradually change from violet to red as the hotend gets to temperature
|
||
* - Change to white to illuminate work surface
|
||
* - Change to green once print has finished
|
||
* - Turn off after the print has finished and the user has pushed a button
|
||
*/
|
||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||
#define PRINTER_EVENT_LEDS
|
||
#endif
|
||
|
||
/*********************************************************************\
|
||
* R/C SERVO support
|
||
* Sponsored by TrinityLabs, Reworked by codexmas
|
||
**********************************************************************/
|
||
|
||
// Number of servos
|
||
//
|
||
// If you select a configuration below, this will receive a default value and does not need to be set manually
|
||
// set it manually if you have more servos than extruders and wish to manually control some
|
||
// leaving it undefined or defining as 0 will disable the servo subsystem
|
||
// If unsure, leave commented / disabled
|
||
//
|
||
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
|
||
|
||
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
|
||
// 300ms is a good value but you can try less delay.
|
||
// If the servo can't reach the requested position, increase it.
|
||
#define SERVO_DELAY 300
|
||
|
||
// Servo deactivation
|
||
//
|
||
// With this option servos are powered only during movement, then turned off to prevent jitter.
|
||
//#define DEACTIVATE_SERVOS_AFTER_MOVE
|
||
|
||
/**
|
||
* Filament Width Sensor
|
||
*
|
||
* Measures the filament width in real-time and adjusts
|
||
* flow rate to compensate for any irregularities.
|
||
*
|
||
* Also allows the measured filament diameter to set the
|
||
* extrusion rate, so the slicer only has to specify the
|
||
* volume.
|
||
*
|
||
* Only a single extruder is supported at this time.
|
||
*
|
||
* 34 RAMPS_14 : Analog input 5 on the AUX2 connector
|
||
* 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E)
|
||
* 301 RAMBO : Analog input 3
|
||
*
|
||
* Note: May require analog pins to be defined for other boards.
|
||
*/
|
||
//#define FILAMENT_WIDTH_SENSOR
|
||
|
||
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading.
|
||
|
||
#if ENABLED(FILAMENT_WIDTH_SENSOR)
|
||
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3)
|
||
#define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber
|
||
|
||
#define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading
|
||
#define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading
|
||
#define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM.
|
||
|
||
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially
|
||
|
||
// Display filament width on the LCD status line. Status messages will expire after 5 seconds.
|
||
//#define FILAMENT_LCD_DISPLAY
|
||
#endif
|
||
|
||
#endif // CONFIGURATION_H
|