SunRed
/
Marlin-Artillery-M600
Archived
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
This repository has been archived on 2022-01-28. You can view files and clone it, but cannot push or open issues or pull requests.
Marlin-Artillery-M600/Marlin/src/pins/sanguino/pins_ZMIB_V2.h

235 lines
7.5 KiB
C
Raw Blame History

/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <https://www.gnu.org/licenses/>.
*
*/
#pragma once
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__)
#error "Oops! Select 'Sanguino' in 'Tools > Boards' and 'ATmega644P' or 'ATmega1284P' in 'Tools > Processor.'"
#endif
#define BOARD_INFO_NAME "Zonestar ZMIB_V2"
#define BOARD_WEBSITE_URL "https://www.aliexpress.com/item/32957490744.html"
#define IS_ZMIB_V2
/**
* ZMIB pin assignments
*
* The ZMIB board needs a bootloader installed before Marlin can be uploaded.
* If you don't have a chip programmer you can use a spare Arduino plus a few
* electronic components to write the bootloader.
*
* See http://www.instructables.com/id/Burn-Arduino-Bootloader-with-Arduino-MEGA/
*/
/**
* PIN: 0 Port: B0 HEATER_0_PIN
* PIN: 1 Port: B1 HEATER_BED_PIN
* PIN: 2 Port: B2 EXP1_4(BTN_EN2)
* PIN: 3 Port: B3 V1: SD_DETECT_PIN
* PIN: 3 Port: B3 V2: EXP1_6
* PIN: 4 Port: B4 SDSS
* PIN: 4 Port: B4 V1: EXP1_6
* PIN: 5 Port: B5 AVR_MOSI_PIN
* . MOSI_PIN
* PIN: 6 Port: B6 AVR_MISO_PIN
* . EXP1_9(MISO_PIN)
* PIN: 7 Port: B7 AVR_SCK_PIN
* . EXP1_10(SCK_PIN)
* PIN: 8 Port: D0 RXD
* PIN: 9 Port: D1 TXD
* PIN: 10 Port: D2 EXP1_8
* PIN: 11 Port: D3 EXP1_7
* PIN: 12 Port: D4 EXP1_5(BTN_EN1)
* PIN: 13 Port: D5 Z_MIN_PIN
* PIN: 14 Port: D6 E1_DIR_PIN
* PIN: 15 Port: D7 E1_STEP_PIN
* PIN: 16 Port: C0 Z_DIR_PIN
* PIN: 17 Port: C1 Z_STEP_PIN
* PIN: 18 Port: C2 Y_MIN_PIN
* PIN: 19 Port: C3 Y_DIR_PIN
* PIN: 20 Port: C4 Y_STEP_PIN
* PIN: 21 Port: C5 X_MIN_PIN
* PIN: 22 Port: C6 X_DIR_PIN
* PIN: 23 Port: C7 X_STEP_PIN
* PIN: 24 Port: A7 X_ENABLE_PIN
* Y_ENABLE_PIN
* Z_ENABLE_PIN
* E0_ENABLE_PIN
* E1_ENABLE_PIN
* PIN: 25 Port: A6 FIL_RUNOUT_PIN
* PIN: 26 Port: A5 E0_DIR_PIN
* PIN: 27 Port: A4 E0_STEP_PIN
* PIN: 28 Port: A3 FAN_PIN
* PIN: 29 Port: A2 EXP1_3(BTN_ENC)
* ADC_KEY_PIN
* PIN: 30 Port: A1 TEMP_0_PIN
* PIN: 31 Port: A0 TEMP_BED_PIN
*/
//
// Limit Switches
//
#define X_MIN_PIN 21
#define Y_MIN_PIN 18
#if EITHER(Z6S_ZFAULT, Z6BS_ZFAULT)
#define Z_MIN_PIN 25
#else
#define Z_MIN_PIN 13
#endif
//
// Steppers
//
#define X_STEP_PIN 23
#define X_DIR_PIN 22
#define X_ENABLE_PIN 24
#define Y_STEP_PIN 20
#define Y_DIR_PIN 19
#define Y_ENABLE_PIN 24
#if EITHER(Z6S_ZFAULT, Z6BS_ZFAULT)
#define Z_STEP_PIN 27
#define Z_DIR_PIN 26
#else
#define Z_STEP_PIN 17
#define Z_DIR_PIN 16
#endif
#define Z_ENABLE_PIN 24
#if EITHER(Z6S_ZFAULT, Z6BS_ZFAULT)
#define E0_STEP_PIN 15
#define E0_DIR_PIN 14
#else
#define E0_STEP_PIN 27
#define E0_DIR_PIN 26
#endif
#define E0_ENABLE_PIN 24
#define E1_STEP_PIN 15
#define E1_DIR_PIN 14
#define E1_ENABLE_PIN 24
//
// Temperature Sensors
//
#define TEMP_0_PIN 1 // Analog Input
#define TEMP_BED_PIN 0 // Analog Input
//
// Heaters / Fans
//
#define HEATER_0_PIN 0
#define HEATER_BED_PIN 1
#define FAN_PIN 28
#define FAN1_PIN -1
//
//filament run out sensor
//
#if EITHER(Z6S_ZFAULT, Z6BS_ZFAULT)
#define FIL_RUNOUT_PIN 13
#else
#define FIL_RUNOUT_PIN 25 // Z-MIN
#endif
//
// SD card
//
#if ENABLED(SDSUPPORT)
#define SDSS 4
#endif
#define SD_DETECT_PIN -1
/*===================================================
* ZMIB Version 1 - EXP1 Connector
* MOSI(D5) TX1(D11) ENA(D12) ENC(D29/A2) 5V
* SCK(D7) RX1(D10) SCS(D4) ENB(D2) GND
*===================================================
* ZMIB Version 2 - EXP1 Connector
* MOSI(D5) TX1(D11) ENA(D12) ENC(D29/A2) 5V
* SCK(D7) RX1(D10) SCS(D3) ENB(D2) GND
*===================================================
* LCD 128x64
*==================================================*/
#if ENABLED(ZONESTAR_12864LCD)
//
// LCD 128x64
//
#define LCDSCREEN_NAME "ZONESTAR_12864LCD"
#define FORCE_SOFT_SPI
//#define LCD_SDSS 11
#define LCD_PINS_RS 11 // ST7920_CS_PIN LCD_PIN_RS (PIN4 of LCD module)
#ifdef IS_ZMIB_V2
#define LCD_PINS_ENABLE 3 // ST7920_DAT_PIN LCD_PIN_R/W (PIN5 of LCD module)
#else
#define LCD_PINS_ENABLE 4 // ST7920_DAT_PIN LCD_PIN_R/W (PIN5 of LCD module)
#endif
#define LCD_PINS_D4 10 // ST7920_CLK_PIN LCD_PIN_ENABLE (PIN6 of LCD module)
// Alter timing for graphical display
#define ST7920_DELAY_1 DELAY_2_NOP
#define ST7920_DELAY_2 DELAY_2_NOP
#define ST7920_DELAY_3 DELAY_2_NOP
#elif EITHER(ZONESTAR_12864OLED, ZONESTAR_12864OLED_SSD1306)
//
// OLED 128x64
//
#define LCDSCREEN_NAME "ZONESTAR 12864OLED"
#define FORCE_SOFT_SPI
#ifdef IS_ZMIB_V2
#define LCD_PINS_RS 3 // RESET
#else
#define LCD_PINS_RS 4 // RESET
#endif
#define LCD_PINS_DC 10 // DC
#define DOGLCD_CS 11 // CS
#if ENABLED(OLED_HW_IIC)
#error "Oops! can't choose HW IIC for ZMIB board!!"
#elif ENABLED(OLED_HW_SPI)
// HW SPI
#define DOGLCD_A0 LCD_PINS_DC // A0 = DC
#else
// SW SPI
#define DOGLCD_A0 LCD_PINS_DC // A0 = DC
#define DOGLCD_MOSI AVR_MOSI_PIN // SDA
#define DOGLCD_SCK AVR_SCK_PIN // SCK
#endif
#endif
//
// All the above are also RRDSC with rotary encoder
//
#if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)
#define BTN_EN1 2
#define BTN_EN2 12
#define BTN_ENC 29
#define BEEPER_PIN -1
#define KILL_PIN -1
#endif
Reference in New Issue View Git Blame Copy Permalink