Update delta configs with latest settings
This commit is contained in:
Scott Lahteine
Richard Wackerbarth
parent
e6baf8afd9
commit
98c9111a7d
4 changed files with 85 additions and 162 deletions
|
|
@ -355,6 +355,7 @@ Here are some standard links for getting your machine calibrated:
|
|||
// #define ENDSTOPPULLUP_XMIN
|
||||
// #define ENDSTOPPULLUP_YMIN
|
||||
// #define ENDSTOPPULLUP_ZMIN
|
||||
// #define ENDSTOPPULLUP_ZPROBE
|
||||
#endif
|
||||
|
||||
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
|
||||
|
|
@ -368,6 +369,12 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
|||
//#define DISABLE_MAX_ENDSTOPS
|
||||
#define DISABLE_MIN_ENDSTOPS // Deltas only use min endstops for probing
|
||||
|
||||
// If you want to enable the Z Probe pin, but disable its use, uncomment the line below.
|
||||
// This only affects a Z Probe Endstop if you have separate Z min endstop as well and have
|
||||
// activated Z_PROBE_ENDSTOP below. If you are using the Z Min endstop on your Z Probe,
|
||||
// this has no effect.
|
||||
//#define DISABLE_Z_PROBE_ENDSTOP
|
||||
|
||||
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
||||
// :{0:'Low',1:'High'}
|
||||
#define X_ENABLE_ON 0
|
||||
|
|
@ -430,8 +437,11 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
|||
// In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made.
|
||||
// It is assumed that when logic high = filament available
|
||||
// when logic low = filament ran out
|
||||
//const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
|
||||
//#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
|
||||
#ifdef FILAMENT_RUNOUT_SENSOR
|
||||
const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
|
||||
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
|
||||
#define FILAMENT_RUNOUT_SCRIPT "M600"
|
||||
#endif
|
||||
|
||||
//===========================================================================
|
||||
//=========================== Manual Bed Leveling ===========================
|
||||
|
|
@ -824,6 +834,10 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
|||
// Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
|
||||
//#define LCD_I2C_VIKI
|
||||
|
||||
// SSD1306 OLED generic display support
|
||||
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
|
||||
//#define U8GLIB_SSD1306
|
||||
|
||||
// Shift register panels
|
||||
// ---------------------
|
||||
// 2 wire Non-latching LCD SR from:
|
||||
|
|
|
|||
|
|
@ -355,6 +355,7 @@ Here are some standard links for getting your machine calibrated:
|
|||
// #define ENDSTOPPULLUP_XMIN
|
||||
// #define ENDSTOPPULLUP_YMIN
|
||||
// #define ENDSTOPPULLUP_ZMIN
|
||||
// #define ENDSTOPPULLUP_ZPROBE
|
||||
#endif
|
||||
|
||||
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
|
||||
|
|
@ -368,6 +369,12 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
|||
//#define DISABLE_MAX_ENDSTOPS
|
||||
#define DISABLE_MIN_ENDSTOPS // Deltas only use min endstops for probing
|
||||
|
||||
// If you want to enable the Z Probe pin, but disable its use, uncomment the line below.
|
||||
// This only affects a Z Probe Endstop if you have separate Z min endstop as well and have
|
||||
// activated Z_PROBE_ENDSTOP below. If you are using the Z Min endstop on your Z Probe,
|
||||
// this has no effect.
|
||||
//#define DISABLE_Z_PROBE_ENDSTOP
|
||||
|
||||
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
||||
// :{0:'Low',1:'High'}
|
||||
#define X_ENABLE_ON 0
|
||||
|
|
@ -827,6 +834,10 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
|||
// Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
|
||||
//#define LCD_I2C_VIKI
|
||||
|
||||
// SSD1306 OLED generic display support
|
||||
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
|
||||
//#define U8GLIB_SSD1306
|
||||
|
||||
// Shift register panels
|
||||
// ---------------------
|
||||
// 2 wire Non-latching LCD SR from:
|
||||
|
|
|
|||
|
|
@ -355,6 +355,7 @@ Here are some standard links for getting your machine calibrated:
|
|||
// #define ENDSTOPPULLUP_XMIN
|
||||
// #define ENDSTOPPULLUP_YMIN
|
||||
// #define ENDSTOPPULLUP_ZMIN
|
||||
// #define ENDSTOPPULLUP_ZPROBE
|
||||
#endif
|
||||
|
||||
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
|
||||
|
|
@ -368,6 +369,12 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
|||
//#define DISABLE_MAX_ENDSTOPS
|
||||
//#define DISABLE_MIN_ENDSTOPS // Deltas only use min endstops for probing
|
||||
|
||||
// If you want to enable the Z Probe pin, but disable its use, uncomment the line below.
|
||||
// This only affects a Z Probe Endstop if you have separate Z min endstop as well and have
|
||||
// activated Z_PROBE_ENDSTOP below. If you are using the Z Min endstop on your Z Probe,
|
||||
// this has no effect.
|
||||
//#define DISABLE_Z_PROBE_ENDSTOP
|
||||
|
||||
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
||||
// :{0:'Low',1:'High'}
|
||||
#define X_ENABLE_ON 0
|
||||
|
|
@ -782,6 +789,10 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
|||
// Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
|
||||
//#define LCD_I2C_VIKI
|
||||
|
||||
// SSD1306 OLED generic display support
|
||||
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
|
||||
//#define U8GLIB_SSD1306
|
||||
|
||||
// Shift register panels
|
||||
// ---------------------
|
||||
// 2 wire Non-latching LCD SR from:
|
||||
|
|
|
|||
|
|
@ -307,17 +307,8 @@ Here are some standard links for getting your machine calibrated:
|
|||
* the firmware will halt as a safety precaution.
|
||||
*/
|
||||
|
||||
#define THERMAL_RUNAWAY_PROTECTION_HOTENDS // Enable thermal protection for all extruders
|
||||
#define THERMAL_RUNAWAY_PROTECTION_BED // Enable thermal protection for the heated bed
|
||||
// Parameters for all extruder heaters
|
||||
#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 // in seconds
|
||||
#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius
|
||||
|
||||
// To enable for the bed heater, uncomment the two defines below:
|
||||
|
||||
// Parameters for the bed heater
|
||||
#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 // in seconds
|
||||
#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
|
||||
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
|
||||
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
|
||||
|
||||
//===========================================================================
|
||||
//============================= Mechanical Settings =========================
|
||||
|
|
@ -379,18 +370,10 @@ Here are some standard links for getting your machine calibrated:
|
|||
// #define ENDSTOPPULLUP_XMIN
|
||||
// #define ENDSTOPPULLUP_YMIN
|
||||
// #define ENDSTOPPULLUP_ZMIN
|
||||
// #define ENDSTOPPULLUP_ZPROBE
|
||||
#endif
|
||||
|
||||
#ifdef ENDSTOPPULLUPS
|
||||
#define ENDSTOPPULLUP_XMAX
|
||||
#define ENDSTOPPULLUP_YMAX
|
||||
#define ENDSTOPPULLUP_ZMAX
|
||||
#define ENDSTOPPULLUP_XMIN
|
||||
#define ENDSTOPPULLUP_YMIN
|
||||
#define ENDSTOPPULLUP_ZMIN
|
||||
#endif
|
||||
|
||||
// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
|
||||
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
|
||||
const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
|
|
@ -401,10 +384,11 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
|||
//#define DISABLE_MAX_ENDSTOPS
|
||||
//#define DISABLE_MIN_ENDSTOPS // Deltas only use min endstops for probing
|
||||
|
||||
// Disable max endstops for compatibility with endstop checking routine
|
||||
#if defined(COREXY) && !defined(DISABLE_MAX_ENDSTOPS)
|
||||
#define DISABLE_MAX_ENDSTOPS
|
||||
#endif
|
||||
// If you want to enable the Z Probe pin, but disable its use, uncomment the line below.
|
||||
// This only affects a Z Probe Endstop if you have separate Z min endstop as well and have
|
||||
// activated Z_PROBE_ENDSTOP below. If you are using the Z Min endstop on your Z Probe,
|
||||
// this has no effect.
|
||||
//#define DISABLE_Z_PROBE_ENDSTOP
|
||||
|
||||
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
||||
// :{0:'Low',1:'High'}
|
||||
|
|
@ -477,9 +461,23 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
|||
//===========================================================================
|
||||
//=========================== Manual Bed Leveling ===========================
|
||||
//===========================================================================
|
||||
#define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS)
|
||||
#define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS)
|
||||
#define Z_MAX_LENGTH (Z_MAX_POS - Z_MIN_POS)
|
||||
|
||||
// #define MANUAL_BED_LEVELING // Add display menu option for bed leveling
|
||||
// #define MESH_BED_LEVELING // Enable mesh bed leveling
|
||||
|
||||
#ifdef MANUAL_BED_LEVELING
|
||||
#define MBL_Z_STEP 0.025 // Step size while manually probing Z axis
|
||||
#endif // MANUAL_BED_LEVELING
|
||||
|
||||
#ifdef MESH_BED_LEVELING
|
||||
#define MESH_MIN_X 10
|
||||
#define MESH_MAX_X (X_MAX_POS - MESH_MIN_X)
|
||||
#define MESH_MIN_Y 10
|
||||
#define MESH_MAX_Y (Y_MAX_POS - MESH_MIN_Y)
|
||||
#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited
|
||||
#define MESH_NUM_Y_POINTS 3
|
||||
#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0
|
||||
#endif // MESH_BED_LEVELING
|
||||
|
||||
//===========================================================================
|
||||
//============================ Bed Auto Leveling ============================
|
||||
|
|
@ -507,10 +505,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
|||
// Note: this feature generates 10KB extra code size
|
||||
#define AUTO_BED_LEVELING_GRID // Deltas only support grid mode
|
||||
|
||||
// with AUTO_BED_LEVELING_GRID, the bed is sampled in a
|
||||
// AUTO_BED_LEVELING_GRID_POINTSxAUTO_BED_LEVELING_GRID_POINTS grid
|
||||
// and least squares solution is calculated
|
||||
// Note: this feature occupies 10'206 byte
|
||||
#ifdef AUTO_BED_LEVELING_GRID
|
||||
|
||||
// set the rectangle in which to probe
|
||||
|
|
@ -521,16 +515,10 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
|||
#define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
|
||||
|
||||
#define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this
|
||||
// probe at the points of a lattice grid
|
||||
#define AUTO_BED_LEVELING_GRID_POINTS 7
|
||||
#define AUTO_BED_LEVELING_GRID_X ((RIGHT_PROBE_BED_POSITION - LEFT_PROBE_BED_POSITION) / (AUTO_BED_LEVELING_GRID_POINTS - 1))
|
||||
#define AUTO_BED_LEVELING_GRID_Y ((BACK_PROBE_BED_POSITION - FRONT_PROBE_BED_POSITION) / (AUTO_BED_LEVELING_GRID_POINTS - 1))
|
||||
|
||||
// Non-linear bed leveling will be used.
|
||||
// Compensate by interpolating between the nearest four Z probe values for each point.
|
||||
// Useful for deltas where the print surface may appear like a bowl or dome shape.
|
||||
// Works best with ACCURATE_BED_LEVELING_POINTS 5 or higher.
|
||||
#define NONLINEAR_BED_LEVELING
|
||||
// Set the number of grid points per dimension
|
||||
// You probably don't need more than 3 (squared=9)
|
||||
#define AUTO_BED_LEVELING_GRID_POINTS 7
|
||||
|
||||
#else // !AUTO_BED_LEVELING_GRID
|
||||
|
||||
|
|
@ -710,8 +698,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
|||
* MOVEMENT SETTINGS
|
||||
*/
|
||||
|
||||
////// #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
|
||||
// set the homing speeds (mm/min)
|
||||
/// delta homing speeds must be the same on xyz
|
||||
#define HOMING_FEEDRATE_X (200*60)
|
||||
#define HOMING_FEEDRATE_Y (200*60)
|
||||
|
|
@ -735,12 +721,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
|||
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
|
||||
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
|
||||
|
||||
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
||||
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
||||
// For the other hotends it is their distance from the extruder 0 hotend.
|
||||
// #define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
// #define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
|
||||
#define DEFAULT_XYJERK 20.0 // (mm/sec)
|
||||
#define DEFAULT_ZJERK 20.0 // (mm/sec) Must be same as XY for delta
|
||||
|
|
@ -771,6 +751,8 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
|||
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
|
||||
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
|
||||
//define this to enable EEPROM support
|
||||
//#define EEPROM_SETTINGS
|
||||
|
||||
#ifdef EEPROM_SETTINGS
|
||||
// To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
|
||||
#define EEPROM_CHITCHAT // Please keep turned on if you can.
|
||||
|
|
@ -814,6 +796,9 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
|||
//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
|
||||
//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
|
||||
// 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms>
|
||||
// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
|
||||
// http://reprap.org/wiki/PanelOne
|
||||
//#define PANEL_ONE
|
||||
|
||||
// The MaKr3d Makr-Panel with graphic controller and SD support
|
||||
// http://reprap.org/wiki/MaKr3d_MaKrPanel
|
||||
|
|
@ -829,6 +814,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
|||
//
|
||||
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
|
||||
//#define ELB_FULL_GRAPHIC_CONTROLLER
|
||||
//#define SDCARDDETECTINVERTED
|
||||
|
||||
// The RepRapDiscount Smart Controller (white PCB)
|
||||
// http://reprap.org/wiki/RepRapDiscount_Smart_Controller
|
||||
|
|
@ -854,136 +840,37 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
|||
// REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARDUINO library folder: https://github.com/kiyoshigawa/LiquidCrystal_I2C
|
||||
//#define RA_CONTROL_PANEL
|
||||
|
||||
//automatic expansion
|
||||
#if defined (MAKRPANEL)
|
||||
#define DOGLCD
|
||||
#define SDSUPPORT
|
||||
#define ULTIPANEL
|
||||
#define NEWPANEL
|
||||
#define DEFAULT_LCD_CONTRAST 17
|
||||
#endif
|
||||
|
||||
#if defined (REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
|
||||
#define DOGLCD
|
||||
#define U8GLIB_ST7920
|
||||
#define REPRAP_DISCOUNT_SMART_CONTROLLER
|
||||
#endif
|
||||
|
||||
#if defined(ULTIMAKERCONTROLLER) || defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL)
|
||||
#define ULTIPANEL
|
||||
#define NEWPANEL
|
||||
#endif
|
||||
|
||||
#if defined(REPRAPWORLD_KEYPAD)
|
||||
#define NEWPANEL
|
||||
#define ULTIPANEL
|
||||
#endif
|
||||
#if defined(RA_CONTROL_PANEL)
|
||||
#define ULTIPANEL
|
||||
#define NEWPANEL
|
||||
#define LCD_I2C_TYPE_PCA8574
|
||||
#define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander
|
||||
#endif
|
||||
// Delta calibration menu
|
||||
// uncomment to add three points calibration menu option.
|
||||
// See http://minow.blogspot.com/index.html#4918805519571907051
|
||||
// If needed, adjust the X, Y, Z calibration coordinates
|
||||
// in ultralcd.cpp@lcd_delta_calibrate_menu()
|
||||
// #define DELTA_CALIBRATION_MENU
|
||||
|
||||
/**
|
||||
* I2C Panels
|
||||
*/
|
||||
|
||||
//#define LCD_I2C_SAINSMART_YWROBOT
|
||||
#ifdef LCD_I2C_SAINSMART_YWROBOT
|
||||
// This uses the LiquidCrystal_I2C library ( https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home )
|
||||
// Make sure it is placed in the Arduino libraries directory.
|
||||
#define LCD_I2C_TYPE_PCF8575
|
||||
#define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander
|
||||
#define NEWPANEL
|
||||
#define ULTIPANEL
|
||||
#endif
|
||||
|
||||
// PANELOLU2 LCD with status LEDs, separate encoder and click inputs
|
||||
//#define LCD_I2C_PANELOLU2
|
||||
#ifdef LCD_I2C_PANELOLU2
|
||||
// This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 )
|
||||
// Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.
|
||||
// (v1.2.3 no longer requires you to define PANELOLU in the LiquidTWI2.h library header file)
|
||||
// Note: The PANELOLU2 encoder click input can either be directly connected to a pin
|
||||
// (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
|
||||
#define LCD_I2C_TYPE_MCP23017
|
||||
#define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
|
||||
#define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD
|
||||
#define NEWPANEL
|
||||
#define ULTIPANEL
|
||||
|
||||
#ifndef ENCODER_PULSES_PER_STEP
|
||||
#define ENCODER_PULSES_PER_STEP 4
|
||||
#endif
|
||||
|
||||
#ifndef ENCODER_STEPS_PER_MENU_ITEM
|
||||
#define ENCODER_STEPS_PER_MENU_ITEM 1
|
||||
#endif
|
||||
|
||||
|
||||
#ifdef LCD_USE_I2C_BUZZER
|
||||
#define LCD_FEEDBACK_FREQUENCY_HZ 1000
|
||||
#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
|
||||
#endif
|
||||
|
||||
#endif
|
||||
|
||||
// Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
|
||||
//#define LCD_I2C_VIKI
|
||||
#ifdef LCD_I2C_VIKI
|
||||
// This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 )
|
||||
// Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.
|
||||
// Note: The pause/stop/resume LCD button pin should be connected to the Arduino
|
||||
// BTN_ENC pin (or set BTN_ENC to -1 if not used)
|
||||
#define LCD_I2C_TYPE_MCP23017
|
||||
#define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
|
||||
#define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD (requires LiquidTWI2 v1.2.3 or later)
|
||||
#define NEWPANEL
|
||||
#define ULTIPANEL
|
||||
#endif
|
||||
|
||||
// SSD1306 OLED generic display support
|
||||
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
|
||||
//#define U8GLIB_SSD1306
|
||||
|
||||
// Shift register panels
|
||||
// ---------------------
|
||||
// 2 wire Non-latching LCD SR from:
|
||||
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
|
||||
//#define SR_LCD
|
||||
#ifdef SR_LCD
|
||||
#define SR_LCD_2W_NL // Non latching 2 wire shift register
|
||||
//#define NEWPANEL
|
||||
#endif
|
||||
|
||||
// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
|
||||
//#define SAV_3DLCD
|
||||
|
||||
// @section extras
|
||||
#ifdef ULTIPANEL
|
||||
// #define NEWPANEL //enable this if you have a click-encoder panel
|
||||
#define SDSUPPORT
|
||||
#define ULTRA_LCD
|
||||
#ifdef DOGLCD // Change number of lines to match the DOG graphic display
|
||||
#define LCD_WIDTH 20
|
||||
#define LCD_HEIGHT 5
|
||||
#else
|
||||
#define LCD_WIDTH 20
|
||||
#define LCD_HEIGHT 4
|
||||
#endif
|
||||
#else //no panel but just LCD
|
||||
#ifdef ULTRA_LCD
|
||||
#ifdef DOGLCD // Change number of lines to match the 128x64 graphics display
|
||||
#define LCD_WIDTH 20
|
||||
#define LCD_HEIGHT 5
|
||||
#else
|
||||
#define LCD_WIDTH 16
|
||||
#define LCD_HEIGHT 2
|
||||
#endif
|
||||
#endif
|
||||
#endif
|
||||
|
||||
// default LCD contrast for dogm-like LCD displays
|
||||
#ifdef DOGLCD
|
||||
# ifndef DEFAULT_LCD_CONTRAST
|
||||
# define DEFAULT_LCD_CONTRAST 32
|
||||
# endif
|
||||
#endif
|
||||
|
||||
// Increase the FAN pwm frequency. Removes the PWM noise but increases heating in the FET/Arduino
|
||||
//#define FAST_PWM_FAN
|
||||
|
|
|
|||
Reference in a new issue