Move code block of probe to appropriate position

2016-06-21 20:32:00 +09:00 · 2016-06-21 20:32:00 +09:00 · aa6d35bd49
commit aa6d35bd49
parent 740fb2ce39
18 changed files with 792 additions and 792 deletions
--- a/Marlin/example_configurations/Felix/Configuration.h
+++ b/Marlin/example_configurations/Felix/Configuration.h
@ -391,50 +391,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //============================= Z Probe Options =============================
 //===========================================================================
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 //
 // Probe Type
 // Probes are sensors/switches that are activated / deactivated before/after use.
@ -486,6 +442,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // Allen Key Probe is defined in the Delta example configurations.
 //
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 // Enable Z Probe Repeatability test to see how accurate your probe is
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
--- a/Marlin/example_configurations/Felix/DUAL/Configuration.h
+++ b/Marlin/example_configurations/Felix/DUAL/Configuration.h
@ -389,50 +389,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //============================= Z Probe Options =============================
 //===========================================================================
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 //
 // Probe Type
 // Probes are sensors/switches that are activated / deactivated before/after use.
@ -484,6 +440,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // Allen Key Probe is defined in the Delta example configurations.
 //
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 // Enable Z Probe Repeatability test to see how accurate your probe is
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
--- a/Marlin/example_configurations/Hephestos/Configuration.h
+++ b/Marlin/example_configurations/Hephestos/Configuration.h
@ -401,50 +401,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 //============================= Z Probe Options =============================
 //===========================================================================
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 //
 // Probe Type
 // Probes are sensors/switches that are activated / deactivated before/after use.
@ -496,6 +452,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 // Allen Key Probe is defined in the Delta example configurations.
 //
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 // Enable Z Probe Repeatability test to see how accurate your probe is
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
--- a/Marlin/example_configurations/Hephestos_2/Configuration.h
+++ b/Marlin/example_configurations/Hephestos_2/Configuration.h
@ -403,50 +403,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //============================= Z Probe Options =============================
 //===========================================================================
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 //
 // Probe Type
 // Probes are sensors/switches that are activated / deactivated before/after use.
@ -498,6 +454,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // Allen Key Probe is defined in the Delta example configurations.
 //
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 // Enable Z Probe Repeatability test to see how accurate your probe is
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
--- a/Marlin/example_configurations/K8200/Configuration.h
+++ b/Marlin/example_configurations/K8200/Configuration.h
@ -426,50 +426,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //============================= Z Probe Options =============================
 //===========================================================================
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 //
 // Probe Type
 // Probes are sensors/switches that are activated / deactivated before/after use.
@ -521,6 +477,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // Allen Key Probe is defined in the Delta example configurations.
 //
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 // Enable Z Probe Repeatability test to see how accurate your probe is
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
--- a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
+++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
@ -409,50 +409,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //============================= Z Probe Options =============================
 //===========================================================================
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 //
 // Probe Type
 // Probes are sensors/switches that are activated / deactivated before/after use.
@ -504,6 +460,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // Allen Key Probe is defined in the Delta example configurations.
 //
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 // Enable Z Probe Repeatability test to see how accurate your probe is
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
--- a/Marlin/example_configurations/RigidBot/Configuration.h
+++ b/Marlin/example_configurations/RigidBot/Configuration.h
@ -403,50 +403,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //============================= Z Probe Options =============================
 //===========================================================================
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 //
 // Probe Type
 // Probes are sensors/switches that are activated / deactivated before/after use.
@ -498,6 +454,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // Allen Key Probe is defined in the Delta example configurations.
 //
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 // Enable Z Probe Repeatability test to see how accurate your probe is
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
--- a/Marlin/example_configurations/SCARA/Configuration.h
+++ b/Marlin/example_configurations/SCARA/Configuration.h
@ -417,50 +417,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //============================= Z Probe Options =============================
 //===========================================================================
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 //
 // Probe Type
 // Probes are sensors/switches that are activated / deactivated before/after use.
@ -512,6 +468,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // Allen Key Probe is defined in the Delta example configurations.
 //
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 // Enable Z Probe Repeatability test to see how accurate your probe is
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
--- a/Marlin/example_configurations/TAZ4/Configuration.h
+++ b/Marlin/example_configurations/TAZ4/Configuration.h
@ -430,50 +430,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //============================= Z Probe Options =============================
 //===========================================================================
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 //
 // Probe Type
 // Probes are sensors/switches that are activated / deactivated before/after use.
@ -525,6 +481,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // Allen Key Probe is defined in the Delta example configurations.
 //
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 // Enable Z Probe Repeatability test to see how accurate your probe is
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
--- a/Marlin/example_configurations/WITBOX/Configuration.h
+++ b/Marlin/example_configurations/WITBOX/Configuration.h
@ -401,50 +401,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 //============================= Z Probe Options =============================
 //===========================================================================
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 //
 // Probe Type
 // Probes are sensors/switches that are activated / deactivated before/after use.
@ -496,6 +452,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 // Allen Key Probe is defined in the Delta example configurations.
 //
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 // Enable Z Probe Repeatability test to see how accurate your probe is
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
--- a/Marlin/example_configurations/adafruit/ST7565/Configuration.h
+++ b/Marlin/example_configurations/adafruit/ST7565/Configuration.h
@ -409,50 +409,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //============================= Z Probe Options =============================
 //===========================================================================
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 //
 // Probe Type
 // Probes are sensors/switches that are activated / deactivated before/after use.
@ -504,6 +460,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // Allen Key Probe is defined in the Delta example configurations.
 //
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 // Enable Z Probe Repeatability test to see how accurate your probe is
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
--- a/Marlin/example_configurations/delta/biv2.5/Configuration.h
+++ b/Marlin/example_configurations/delta/biv2.5/Configuration.h
@ -451,50 +451,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 //============================= Z Probe Options =============================
 //===========================================================================
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 //
 // Probe Type
 // Probes are sensors/switches that are activated / deactivated before/after use.
@ -583,6 +539,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 #endif // Z_PROBE_ALLEN_KEY
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 // Enable Z Probe Repeatability test to see how accurate your probe is
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
--- a/Marlin/example_configurations/delta/generic/Configuration.h
+++ b/Marlin/example_configurations/delta/generic/Configuration.h
@ -451,50 +451,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 //============================= Z Probe Options =============================
 //===========================================================================
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 #define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 //#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 //
 // Probe Type
 // Probes are sensors/switches that are activated / deactivated before/after use.
@ -577,6 +533,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 #endif // Z_PROBE_ALLEN_KEY
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 #define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 //#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 // Enable Z Probe Repeatability test to see how accurate your probe is
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
--- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h
@ -451,50 +451,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //============================= Z Probe Options =============================
 //===========================================================================
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 //
 // Probe Type
 // Probes are sensors/switches that are activated / deactivated before/after use.
@ -580,6 +536,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #endif // Z_PROBE_ALLEN_KEY
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 // Enable Z Probe Repeatability test to see how accurate your probe is
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
--- a/Marlin/example_configurations/delta/kossel_pro/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_pro/Configuration.h
@ -440,50 +440,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //============================= Z Probe Options =============================
 //===========================================================================
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 //
 // Probe Type
 // Probes are sensors/switches that are activated / deactivated before/after use.
@ -574,6 +530,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #endif // Z_PROBE_ALLEN_KEY
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 // Enable Z Probe Repeatability test to see how accurate your probe is
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
--- a/Marlin/example_configurations/delta/kossel_xl/Configuration.h
+++ b/Marlin/example_configurations/delta/kossel_xl/Configuration.h
@ -449,50 +449,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //============================= Z Probe Options =============================
 //===========================================================================
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 #define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 //#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 //
 // Probe Type
 // Probes are sensors/switches that are activated / deactivated before/after use.
@ -575,6 +531,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 #endif // Z_PROBE_ALLEN_KEY
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 #define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 //#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 // Enable Z Probe Repeatability test to see how accurate your probe is
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
--- a/Marlin/example_configurations/makibox/Configuration.h
+++ b/Marlin/example_configurations/makibox/Configuration.h
@ -412,50 +412,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 //============================= Z Probe Options =============================
 //===========================================================================
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 //
 // Probe Type
 // Probes are sensors/switches that are activated / deactivated before/after use.
@ -507,6 +463,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // Allen Key Probe is defined in the Delta example configurations.
 //
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 // Enable Z Probe Repeatability test to see how accurate your probe is
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
--- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h
+++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h
@ -399,50 +399,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 //============================= Z Probe Options =============================
 //===========================================================================
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 //
 // Probe Type
 // Probes are sensors/switches that are activated / deactivated before/after use.
@ -494,6 +450,50 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 // Allen Key Probe is defined in the Delta example configurations.
 //
 // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
 // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
 //
 // *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
 //
 // To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
 // Example: To park the head outside the bed area when homing with G28.
 //
 // To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
 //
 // For a servo-based Z probe, you must set up servo support below, including
 // NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
 //
 // - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
 // - Use 5V for powered (usu. inductive) sensors.
 // - Otherwise connect:
 //   - normally-closed switches to GND and D32.
 //   - normally-open switches to 5V and D32.
 //
 // Normally-closed switches are advised and are the default.
 //
 // The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
 // Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
 // default pin for all RAMPS-based boards. Some other boards map differently.
 // To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
 //
 // WARNING:
 // Setting the wrong pin may have unexpected and potentially disastrous consequences.
 // Use with caution and do your homework.
 //
 //#define Z_MIN_PROBE_ENDSTOP
 // Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
 // The Z_MIN_PIN will then be used for both Z-homing and probing.
 #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 // To use a probe you must enable one of the two options above!
 // This option disables the use of the Z_MIN_PROBE_PIN
 // To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
 // Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 // Enable Z Probe Repeatability test to see how accurate your probe is
 //#define Z_MIN_PROBE_REPEATABILITY_TEST