Add PROBING_STEPPERS_OFF (#11984)

Co-Authored-By: houseofbugs <houseofbugs@gmail.com>

Marlin/Configuration.h

@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/default/Configuration.h

@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h

@@ -879,6 +879,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/AliExpress/CL-260/Configuration.h

@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Anet/A2/Configuration.h

@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Anet/A2plus/Configuration.h

@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Anet/A6/Configuration.h

@@ -935,7 +935,8 @@
 #if ENABLED(PROBING_HEATERS_OFF)
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
-#define PROBING_FANS_OFF          // Turn fans off when probing
+#define PROBING_FANS_OFF            // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Anet/A8/Configuration.h

@@ -866,6 +866,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Azteeg/X5GT/Configuration.h

@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h

@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h

@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/BQ/Hephestos/Configuration.h

@@ -847,6 +847,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h

@@ -860,6 +860,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/BQ/WITBOX/Configuration.h

@@ -847,6 +847,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Cartesio/Configuration.h

@@ -858,6 +858,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Creality/CR-10/Configuration.h

@@ -869,6 +869,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Creality/CR-10S/Configuration.h

@@ -863,6 +863,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Creality/CR-10mini/Configuration.h

@@ -878,6 +878,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Creality/CR-8/Configuration.h

@@ -869,6 +869,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Creality/Ender-2/Configuration.h

@@ -863,6 +863,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Creality/Ender-3/Configuration.h

@@ -863,6 +863,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Creality/Ender-4/Configuration.h

@@ -869,6 +869,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Einstart-S/Configuration.h

@@ -869,6 +869,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Felix/Configuration.h

@@ -841,6 +841,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Felix/DUAL/Configuration.h

@@ -841,6 +841,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h

@@ -865,6 +865,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Formbot/Raptor/Configuration.h

@@ -849,20 +849,6 @@
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
 #endif
 
-/**
- * Enable one or more of the following if probing seems unreliable.
- * Heaters and/or fans can be disabled during probing to minimize electrical
- * noise. A delay can also be added to allow noise and vibration to settle.
- * These options are most useful for the BLTouch probe, but may also improve
- * readings with inductive probes and piezo sensors.
- */
-//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
-#if ENABLED(PROBING_HEATERS_OFF)
-  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
-#endif
-//#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
-
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
 //#define SOLENOID_PROBE
 
@@ -955,6 +941,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Formbot/T_Rex_2+/Configuration.h

@@ -897,6 +897,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Formbot/T_Rex_3/Configuration.h

@@ -880,6 +880,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Geeetech/GT2560/Configuration.h

@@ -874,6 +874,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h

@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h

@@ -874,8 +874,9 @@
 #if ENABLED(PROBING_HEATERS_OFF)
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
-#define PROBING_FANS_OFF          // Turn fans off when probing
+#define PROBING_FANS_OFF            // Turn fans off when probing
-#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
+#define DELAY_BEFORE_PROBING 200    // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{ 0:'Low', 1:'High' }

Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h

@@ -874,6 +874,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h

@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h

@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Infitary/i3-M508/Configuration.h

@@ -863,6 +863,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/JGAurora/A5/Configuration.h

@@ -871,6 +871,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/MakerParts/Configuration.h

@@ -879,6 +879,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Malyan/M150/Configuration.h

@@ -883,6 +883,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Malyan/M200/Configuration.h

@@ -858,6 +858,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Micromake/C1/basic/Configuration.h

@@ -863,6 +863,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h

@@ -863,6 +863,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Mks/Sbase/Configuration.h

@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h

@@ -899,6 +899,7 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h

@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/RigidBot/Configuration.h

@@ -857,6 +857,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/SCARA/Configuration.h

@@ -872,6 +872,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/STM32F10/Configuration.h

@@ -861,6 +861,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/STM32F4/Configuration.h

@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Sanguinololu/Configuration.h

@@ -890,6 +890,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/TheBorg/Configuration.h

@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/TinyBoy2/Configuration.h

@@ -910,6 +910,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Tronxy/X1/Configuration.h

@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Tronxy/X3A/Configuration.h

@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Tronxy/X5S/Configuration.h

@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Tronxy/XY100/Configuration.h

@@ -870,6 +870,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h

@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Velleman/K8200/Configuration.h

@@ -888,6 +888,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Velleman/K8400/Configuration.h

@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h

@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration.h

@@ -869,6 +869,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/adafruit/ST7565/Configuration.h

@@ -859,6 +859,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration.h

@@ -1048,6 +1048,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h

@@ -987,6 +987,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h

@@ -986,6 +986,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h

@@ -986,6 +986,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h

@@ -988,7 +988,8 @@
 #if ENABLED(PROBING_HEATERS_OFF)
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
-#define PROBING_FANS_OFF          // Turn fans off when probing
+#define PROBING_FANS_OFF            // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/delta/generic/Configuration.h

@@ -974,6 +974,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/delta/kossel_mini/Configuration.h

@@ -976,6 +976,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/delta/kossel_pro/Configuration.h

@@ -977,6 +977,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/delta/kossel_xl/Configuration.h

@@ -977,6 +977,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h

@@ -872,6 +872,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/makibox/Configuration.h

@@ -862,6 +862,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/stm32f103ret6/Configuration.h

@@ -861,6 +861,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/tvrrug/Round2/Configuration.h

@@ -854,6 +854,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/config/examples/wt150/Configuration.h

@@ -864,6 +864,7 @@
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

Marlin/src/module/probe.cpp

@@ -292,6 +292,12 @@ float zprobe_zoffset; // Initialized by settings.load()
     #if ENABLED(PROBING_FANS_OFF)
       fans_pause(p);
     #endif
+    #if ENABLED(PROBING_STEPPERS_OFF)
+      disable_e_steppers();
+      #if DISABLED(DELTA)
+        disable_X(); disable_Y();
+      #endif
+    #endif
     if (p) safe_delay(
       #if DELAY_BEFORE_PROBING > 25
         DELAY_BEFORE_PROBING