AnHardt
d8860f9ad9
Alway end at the same point
...
Always end at [RIGHT_PROBE_BED_POSITION, BACK_PROBE_BED_POSITION]
Regardles the evennes of auto_bed_leveling_grid_points.
2015-08-11 17:32:11 -05:00
AnHardt
4ca8f4a9a7
Always zigzag
...
Use the shortest way between probing-points.
2015-08-11 17:32:11 -05:00
AnHardt
3d23424121
Add array indexIntoAB[xx][yy]
...
and use it.
2015-08-11 17:32:11 -05:00
AnHardt
e2d69f66b2
Make Z_PROBE a Z_MIN_PROBE (PR#65)
...
Currently we use the probe exclusively as a device to find the build platform(bed).
For the currently supported setups this means, we use it as a additional min-endstop.
A triggered when not deployed probe disturbs the homing process for max-endstops.
Rename ENDSTOPPULLUP_ZPROBE to ENDSTOPPULLUP_ZMIN_PROBE
Rename Z_PROBE_ENDSTOP_INVERTING to Z_MIN_PROBE_ENDSTOP_INVERTING
Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP
Rename DISABLE_Z_PROBE_ENDSTOP to DISABLE_Z_MIN_PROBE_ENDSTOP
Rename Z_PROBE_REPEATABILITY_TEST to Z_MIN_PROBE_REPEATABILITY_TEST
Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP
Adjust comments accordingly
Remove Z_MAX check for the probe in update_endstops().
Using an delta related idea of @clefranc from #61 ,
extended to the general change for all setups.
Tested with Prusa i3, max-z-endstop and permanently triggered z-probe.
Worked for @clefranc's delta.
2015-08-11 14:41:36 -05:00
AnHardt
6a6e863a47
Resolve #2581 by adding a missed ';' (PR#67)
2015-08-10 12:51:59 -05:00
RicardoGA
e09ff79635
Update pins_RAMPS_13.h (PR#64)
...
Now all ramps configuration can enable Filament sensor not only EEB
2015-08-10 05:53:01 -05:00
Fourmi
e6aed7bb4e
Update thermistortables for Hisens Thermistor (PR#2588)
2015-08-09 18:11:14 -05:00
Richard Wackerbarth
9d8cc24abf
Continue from the line following the M999 (PR#60)
...
If the printer is going to accept the M999,
then it should continue from that line number.
2015-08-08 08:08:02 -05:00
wurstnase
f3ab1dba54
Z babystepping for coreXY (PR#47)
...
only X and Y were not implemented
2015-08-04 20:10:09 -05:00
Richard Wackerbarth
35afea1c0e
Restore test
...
PR#2572 Changed this because of faulty Boolean Logic
NOT(A OR (NOT B) OR (NOT C)) !=
(NOT A) AND ((NOT B) OR C))
Besides, the compiler should be smart enough to
optimize this without help from the programmer
2015-08-04 15:22:56 -05:00
Scott Lahteine
6af75f4b5d
Squish down deprecated tests in sanity check
2015-08-03 16:04:48 -05:00
Scott Lahteine
edeb58288e
Use PIN_EXISTS in sanity check
2015-08-03 16:04:48 -05:00
Scott Lahteine
c30b7693e0
Clean up RUMBA pins conditions
2015-08-03 16:04:48 -05:00
Scott Lahteine
46453905d6
Apply remaining ENABLED/DISABLED conditionals
2015-08-03 16:04:48 -05:00
Richard Wackerbarth
b227d8c128
Supply a VERSION in a short form for displays
...
The long descriptor will still be available in M115
2015-08-03 08:21:09 -05:00
Richard Wackerbarth
cd7828a928
This will be the 1.1.0 Release rather than 1.0.3
2015-08-03 08:08:38 -05:00
Richard Wackerbarth
4e2f5618c1
Pick up Default_version when needed
2015-08-03 08:08:37 -05:00
Richard Wackerbarth
329acc852e
Canonize Option flag USE_AUTOMATIC_VERSION
2015-08-03 08:08:37 -05:00
Richard Wackerbarth
5a11d32a85
Move deprecation test to SanityCheck.h
2015-08-03 08:08:37 -05:00
Richard Wackerbarth
7bb7a52940
Bring config up-to-date
2015-08-03 07:35:33 -05:00
AnHardt
244ea2014a
Boot-screen for text-displays improvements
...
Centred the logo for 16x4 and 20 x4.
Moved version to the bottom line
Code shrink to 704 bytes.
2015-08-03 07:13:00 -05:00
AnHardt
80f2a20842
Enable bootscreen in all Configurations
2015-08-03 07:13:00 -05:00
AnHardt
2684d061ed
Scroll too long strings on bootscreen
2015-08-03 07:13:00 -05:00
AnHardt
4f46df5dab
Make bootscreen configurable for the graphic displays
...
Saves about 473 byte of progmem and 28 bytes of RAM.
2015-08-03 07:13:00 -05:00
AnHardt
09571b7753
Boot-screen for the character displays
...
Uses about 488 byte of progmem and 32 byte of RAM.
For that configurable.
2015-08-03 07:13:00 -05:00
Richard Wackerbarth
866efc14fe
Add Danish translations
2015-08-03 07:06:17 -05:00
Scott Lahteine
267f3479d7
Adjust spacing in pins_RAMPS_13.h
2015-08-02 23:26:58 -05:00
Scott Lahteine
56702e7bb9
Define servo pins just like other pins
2015-08-02 23:26:58 -05:00
Richard Wackerbarth
4b9d5cd352
Use lowercase names for serial instances
2015-08-02 23:01:39 -05:00
Scott Lahteine
1e2deff4fd
Rename BTENABLED to BLUETOOTH
...
- For some reason it’s easy to forget what BT stands for, but it
doesn’t need an abbreviation.
2015-08-02 22:56:50 -05:00
Scott Lahteine
68055a5959
Include RIGIDBOT_PANEL in Conditionals
2015-08-02 22:26:41 -05:00
George Djabarov
f8ed3a835d
Added comment with the RigidBot Big bed size
2015-08-02 22:13:37 -05:00
George Djabarov
7deae6b6be
Updated RigidBot example configuration
...
- The default serial baud rate of 115200
- The regular RigitBot bed size 254mm/248mm/254mm
- Single stock extruder
- Stock termistors for extruder and hotbed
- Stock Min X/Y/Z stops. Max stops not connected
- Stock 32 teth tooleys (stock axis steps)
- No auto bed leveling
- No screen
2015-08-02 22:13:37 -05:00
Scott Lahteine
5418faa1f9
Add sanity checks for old names
2015-08-02 22:09:08 -05:00
Scott Lahteine
f03e063750
Rename BEEPER to BEEPER_PIN
...
For consistency with other pins, allowing use of `PIN_EXISTS` macro.
2015-08-02 22:09:08 -05:00
Scott Lahteine
270c766de2
SDCARDDETECT -> SD_DETECT, added docs
...
- `SD_DETECT_PIN` replaces `SDCARDDETECT`
- `SD_DETECT_INVERTED` replaces `SDCARDDETECTINVERTED`
- Revise the description of `SD_DETECT_INVERTED`
- Add a note about the override of `SD_DETECT_INVERTED` in
`Conditionals.h`
2015-08-02 21:59:41 -05:00
Scott Lahteine
496fc28dc3
Tweaks to pins comments
2015-08-02 21:34:13 -05:00
Scott Lahteine
8d3b74cc6e
Rename SDCARDDETECT to SDCARDDETECT_PIN
...
- Rename the pin so it can be tested with `PIN_EXISTS`
- Fix some incorrect tests for `SDCARDDETECT`
2015-08-02 21:34:13 -05:00
Scott Lahteine
0f5ada8cbd
Group the fail case in one negation (PR#2572)
2015-08-01 18:55:50 -05:00
AnHardt
7ddf1cda1d
Improve condition for SERVO_LEVELING (PR#2570)
2015-07-31 22:41:34 -05:00
Richard Wackerbarth
f32048b8f5
In for a penny, in for a pound
2015-07-31 17:13:53 -05:00
Scott Lahteine
e944f960de
Add a sanity check for old name "BEEPER"
2015-07-31 17:13:53 -05:00
Scott Lahteine
8ebf0b92be
Spacing adjustments in some pins files
2015-07-31 17:13:53 -05:00
Scott Lahteine
94a796c8cc
Rename BEEPER to BEEPER_PIN
...
For consistency with other pins, allowing use of `PIN_EXISTS` macro.
2015-07-31 17:13:53 -05:00
Richard Wackerbarth
b217474eab
Compiler Complaints about concatenated tokens (PR#2566)
2015-07-31 17:08:44 -05:00
Scott Lahteine
2460f82d8b
Make proper distinction between BEEPER and HAS_BUZZER
2015-07-31 01:24:33 -05:00
Scott Lahteine
58cfcd4239
Overridable Options - Part 5
...
Apply `ENABLED` / `DISABLED` macros to files needing only a small
number of changes.
2015-07-31 01:24:20 -05:00
Scott Lahteine
5e834352a9
Overridable Options - Part 11 (PR#2563)
...
Apply `ENABLED` / `DISABLED` macros to EEPROM-related files.
2015-07-31 01:07:04 -05:00
Scott Lahteine
bf6eb93c61
Overridable Options - Part 10 (PR#2562)
...
Apply `ENABLED` / `DISABLED` macros to planner files.
2015-07-31 01:06:29 -05:00
Scott Lahteine
51e89a269c
Overridable Options - Part 9 (PR#2561)
...
Apply `ENABLED` / `DISABLED` macros to temperature-related files.
2015-07-31 01:05:55 -05:00
Scott Lahteine
c35fb88094
Overridable Options - Part 8 (PR#2560)
...
Apply `ENABLED` / `DISABLED` macros to stepper-related files.
2015-07-31 01:05:22 -05:00
Scott Lahteine
0d8989fc14
Overridable Options - Part 7 (PR#2559)
...
Apply `ENABLED` / `DISABLED` macros to LCD-related files.
2015-07-31 01:04:37 -05:00
Scott Lahteine
b4abb0ae7f
Apply ENABLED / DISABLED to Marlin core files (PR#2558)
2015-07-31 01:03:58 -05:00
Scott Lahteine
c0d7ea3e7e
Overridable Options - Part 4 (PR#2556)
...
Apply `ENABLED` / `DISABLED` / `HAS_SERVOS` macros to pins files.
2015-07-31 00:44:53 -05:00
Scott Lahteine
4b40964064
Overridable Options - Part 3 (PR#2555)
...
Apply `ENABLED` / `DISABLED` macros to language-related files.
2015-07-31 00:19:13 -05:00
Scott Lahteine
32683b282b
Include configurator copies of configs
2015-07-31 00:03:36 -05:00
Scott Lahteine
37d1879386
Apply overridables to Configuration files
2015-07-31 00:03:36 -05:00
Scott Lahteine
9d151bb61b
servo_endstop_angles -> servo_endstop_angle
2015-07-30 23:35:57 -05:00
Scott Lahteine
9334479aeb
Minor cleanup of Conditionals.h
2015-07-30 23:35:57 -05:00
Scott Lahteine
1f63293624
servo_endstops -> servo_endstop_id
2015-07-30 23:35:57 -05:00
Scott Lahteine
edaaead7e0
Fix comment about SERVO_ENDSTOP_ANGLES
2015-07-30 23:35:57 -05:00
Scott Lahteine
ed4a6371ad
Add HAS_SERVO_ENDSTOPS to simplify conditonals
2015-07-30 23:35:57 -05:00
Scott Lahteine
70be61d416
Reset filament_size with a loop
2015-07-30 23:31:58 -05:00
Scott Lahteine
ae9274be05
Fix minor compiler warnings in for loops
2015-07-30 23:31:58 -05:00
Scott Lahteine
c7c8cfed6f
Complete M200 output with M503
...
- The contents of EEPROM include filament diameters even with
Volumetric disabled. This change makes `M503` display the full
volumetric settings so that playing back the output of `M503 S0` will
fully restore them.
2015-07-30 23:31:58 -05:00
Scott Lahteine
4a58e447a1
Add array size to servo_endstop_angles (PR#2553)
2015-07-30 23:27:38 -05:00
Andrew Lenharth
a0ae9e30df
don't pass integer by reference, inefficient. (PR#2547)
2015-07-30 17:51:12 -05:00
AnHardt
d03f037a92
Get rid of malloc() and free() (PR#2549)
...
Just the minimal changes to qr_solve.cpp and .h to get rid of malloc() and free().
Saves about 656 bytes of progmem (library-code)
and 22 bytes for static variables.
Should use exactly the same amount of stack as it did before on the heap.
2015-07-30 17:50:31 -05:00
Scott Lahteine
3b2b2313ff
Combine if block related to SERVO_ENDSTOPS
2015-07-30 16:39:05 -05:00
Scott Lahteine
0af2a80e06
Make SERVO_ENDSTOP_ANGLES 2-dimensional
2015-07-30 16:38:56 -05:00
Richard Wackerbarth
525d0dc239
Configurator is out-of-date AGAIN (PR#2550)
2015-07-30 16:36:01 -05:00
Richard Marko
dd22cbbfb8
makefile: add buzzer.cpp (PR#2479)
2015-07-30 07:56:44 -05:00
Scott Lahteine
9f48798ffd
Replace ENABLED with DEFINED for SERVO_ENDSTOPS (PR#2542)
2015-07-30 07:55:29 -05:00
Richard Wackerbarth
ae00fad75b
Rename as M100
2015-07-27 20:31:59 -05:00
Richard Wackerbarth
a401d738df
There is an echo in here
2015-07-27 20:31:59 -05:00
Richard Wackerbarth
ed7d45e8f5
Memory watcher
2015-07-27 20:31:59 -05:00
AnHardt
d17f7ebc8a
Multiply WATCH_TEMP_PERIOD by 1000UL (PR#2535)
...
instead of 1000. Else we get errors with times over 32 seconds.
2015-07-27 20:30:53 -05:00
Scott Lahteine
bea6739774
Don't include Z_RAISE_AFTER_PROBING if not used (PR#2527)
2015-07-27 20:24:33 -05:00
Scott Lahteine
81bba7ed88
More sanity checking for extruder requirements (PR#2531)
2015-07-27 10:14:43 -05:00
AnHardt
87a97f3724
Fix conditions for display strings
2015-07-26 20:41:21 -05:00
AnHardt
aaccea0260
Shift some display only strings from language.h to lenguage_en.h
...
and translate them to German.
2015-07-26 20:41:15 -05:00
Scott Lahteine
e4c01f1c7e
Simplify init with ARRAY_BY_EXTRUDERS1 macro (PR#2507)
2015-07-26 20:40:27 -05:00
Scott Lahteine
ab6f1fdf8b
Move & document ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED (PR#2528)
...
As suggested in #2521
- Move `ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED` because `SDSUPPORT` is
also required.
- Add a note that endstops must be enabled for the feature to have any
effect
2015-07-26 20:36:37 -05:00
Richard Marko
1183c10a2e
makefile: drop -q -q (much quiet) from avrdude flags
...
Annoying when trying to figure out if uploading
actually does something.
2015-07-26 20:31:31 -05:00
Richard Marko
0e064357f4
makefile: use /etc/avrdude/avrdude.conf on linux
...
No need to look for arduino specific avrdude configuration
as distributions ship their own avrdude.conf file that
is compatible with arduino.
2015-07-26 20:31:31 -05:00
Scott Lahteine
bcb7d5a149
Improve sanitycheck for TEMP_SENSOR_1
2015-07-25 21:17:36 -05:00
Scott Lahteine
5b24f59401
Add sanity checks for temp sensors
2015-07-25 21:17:36 -05:00
AnHardt
fd0e81b0c7
Distinguish between BUZZER and SPEAKER (PR#2513)
...
A speaker needs a AC or a pulsed DC to make a sound, a buzzer only needs a DC.
A buzzer has it's own resonator. It works in most cases to feed the buzzer with a pulsed DC, but the sound will not be as loud as with pure DC.
There seem to be boards where the BEEPER-pin is not able to handle a PWM. Obviously intended for a buzzer.
To make these board able to handle a speaker
* replace the PWM based tone()-function again with a on-delay-off-delay loop.
Hopefully the last time I touch the beeper code.
2015-07-24 22:10:04 -05:00
Scott Lahteine
e2957df05c
Shorthand for do_blocking_move_to
2015-07-24 22:07:41 -05:00
Scott Lahteine
819c5b9b50
Adjust comment on Z adjustment
2015-07-24 22:07:41 -05:00
Scott Lahteine
5a7356b6fc
Patch for G29 final Z position
...
Include all the necessary pieces to get the final Z position after
probing the bed, and add commentary about other possible changes.
2015-07-24 22:07:41 -05:00
AnHardt
088e09e052
Add forgotten Marlin_main.cpp
2015-07-24 22:04:49 -05:00
AnHardt
8b876241bd
Some more servo code tweaks
...
Just set up the pin. Don't move to a random position.
Simplify servo::move()
* servo::move() does not need the pin parameter - The pin is set during servo_init() with attach().
* servo::move() does not need a return value.
SERVO_LEVELING is the wrong condition to deactivate the servos.
Remove some temporary (Servo *) variables.
SanityCheck for the servo indexes.
2015-07-24 22:04:49 -05:00
Scott Lahteine
b116c096bd
Reduce set_homing_bump_feedrate, save 42 bytes (PR#2512)
...
Updates to `set_homing_bump_feedrate`:
- Move the string into Program Memory, reduce length by 31 bytes
- Use an auto to get the divisor, adjust it on error
- Set feedrate once, at the end
2015-07-24 22:00:25 -05:00
Scott Lahteine
f7e7862588
Better Sanguinololu & Graphical Controller (PR#2504)
...
- Change suggested at
https://github.com/MarlinFirmware/Marlin/issues/2482#issuecomment-123553
266
2015-07-23 23:47:07 -05:00
Scott Lahteine
a1154d4a20
Enable Y and sanity-check CoreXZ (PR#2509)
2015-07-23 23:46:27 -05:00
Scott Lahteine
932f1c109e
Move servos to the top in pins_MEGACONTROLLER.h
2015-07-23 22:51:41 -05:00
Scott Lahteine
90f8ddfc1e
Apply MINIPANEL to other configs
2015-07-23 22:51:41 -05:00
AndySze
00dbf69b6d
add MINIPANEL defines
2015-07-23 22:51:40 -05:00
AndySze
8ac5e56934
fixed some format problems and cleaned code
2015-07-23 22:51:40 -05:00
AndySze
eef595aa64
add makerlab mega controller pin configs
2015-07-23 22:51:40 -05:00
AnHardt
4e14e152fa
Add Travis tests for CORXY and COREXZ
2015-07-23 19:52:48 -05:00
AnHardt
27d7d2ccab
Correct bracketing for COREXY-XZ
2015-07-23 19:52:21 -05:00
Scott Lahteine
469843427d
Reduce code in gcode_M81 (PR#2497)
2015-07-23 08:14:00 -05:00
Scott Lahteine
c66955aaf9
Mark unchanging arrays as const (PR#2494)
...
The compiler may be able to optimize if it knows an array won’t be
changing.
2015-07-22 21:37:37 -05:00
Scott Lahteine
278aa15301
Add COUNT macro and apply
2015-07-22 18:16:05 -05:00
Scott Lahteine
d85861d296
Move macros, add ENABLED/DISABLED, add includes
2015-07-22 18:16:05 -05:00
Scott Lahteine
17960fd2b0
Neaten up pins_MEGATRONICS.h (PR#2493)
2015-07-22 17:23:22 -05:00
Scott Lahteine
aac2b9aa9d
Reduce code in gcode_M84 (PR#2492)
...
`gcode_M84` only needs to call `finishAndDisableSteppers`, which calls
all the other functions.
2015-07-22 17:22:01 -05:00
Scott Lahteine
4971fa73f9
Add a sanitycheck error for old servo settings (PR#2491)
...
- Documentation solution for #2476
2015-07-22 16:35:10 -05:00
Scott Lahteine
96ace72ddc
Servos attach/detach based only on servo config
...
Assuming #2470 fixed up the main issue.
2015-07-22 16:34:26 -05:00
Richard Wackerbarth
b80a6a8d31
Correct Kossel Pro Configuration_adv (PR#2473)
2015-07-22 16:32:08 -05:00
Scott Lahteine
000a6fce46
Extract update_endstops from stepper ISR (PR#2474)
2015-07-19 18:33:18 -05:00
Scott Lahteine
e83eac312e
Move plan_arc next to prepare_move
2015-07-19 16:18:46 -05:00
Scott Lahteine
5c5936508d
G2/G3 Arcs for Delta
...
- Update prepare_move_delta to take a target argument
- Add Delta support to plan_arc
2015-07-19 16:18:46 -05:00
Scott Lahteine
9f53e2f0c9
Implement COREXZ in stepper.cpp and planner.cpp
2015-07-19 16:17:03 -05:00
Scott Lahteine
fa00e1d97f
Explode conditions common to corexy and cartesian
2015-07-19 16:17:03 -05:00
Scott Lahteine
c7dd5527b4
Add a C_AXIS and Z_HEAD to support COREXZ
2015-07-19 16:17:03 -05:00
Scott Lahteine
129f986ccf
Add COREXZ option to configurations
2015-07-19 16:17:03 -05:00
Scott Lahteine
69b0490b77
Show minimal preheat options in menus (PR#2471)
2015-07-19 16:14:59 -05:00
Scott Lahteine
eacfe132aa
Change the name of servos[] and servo_t
2015-07-19 11:35:48 -07:00
Scott Lahteine
3b23ccd366
Patch servos code for move
...
- Have `Servo::attach` explicitly return -1 if it fails
- Check for -1 in `Servo::move` because `servoIndex` might be 0
- Make `attach` / `detach` calls conditional on `SERVO_LEVELING`
- Move `SERVO_LEVELING` define to `Conditionals.h`
2015-07-19 11:24:23 -07:00
Richard Wackerbarth
54ddc1d417
Simplify DRY RUN (PR#2358)
...
Elsewhere DRYRUN turns off the heating elements
and ignores constraints on them.
Here, whenever motion is entered into the planner,
if DRY RUN is set, we instantly act as if the E_AXIS
is in the desired final position.
2015-07-19 10:15:53 -05:00
Scott Lahteine
944090c19c
Optimize lsDive logic
2015-07-19 10:13:40 -05:00
Scott Lahteine
417706e578
Include space for the terminating nul in lsDive
2015-07-19 10:13:39 -05:00
Scott Lahteine
f3c1a6b19c
Reduce lsDive stack usage to the minimum
2015-07-19 10:13:39 -05:00
Patrick Bogen
fba4e6241b
Specify print format for reporting invalid tmp_extruder (PR#2465)
2015-07-18 16:40:01 -05:00
AnHardt
d15d869267
Rename axis_is_at_home() to set_axis_is_at_home() (PR#2464)
...
to make clear - it's not a question but an order.
2015-07-18 10:27:21 -05:00
Scott Lahteine
f209b755a5
Move the Z probe as far as needed to trigger the switch (PR#2461)
2015-07-16 20:02:44 -05:00
Scott Lahteine
0f1df62389
Fixup comments in code_seen
2015-07-16 16:40:52 -05:00
Scott Lahteine
2945eb6650
Call code_seen only once per parameter
2015-07-16 16:40:52 -05:00
Scott Lahteine
b742af2e2a
Move Y_STOP_PIN for Printrboard with SD (PR#2420)
2015-07-16 16:39:55 -05:00
Scott Lahteine
baa9199973
Define extern delta only for delta
2015-07-16 16:36:30 -05:00
Scott Lahteine
77e80ef367
Require extruders for thermal code
2015-07-16 16:36:30 -05:00
Scott Lahteine
3bde4f4855
Require temp sensor for bed thermal protection
2015-07-16 16:36:30 -05:00
Scott Lahteine
82a3ed2f9a
Cleanup and dev notes in Marlin.h
2015-07-16 16:36:30 -05:00
Scott Lahteine
db23b9b184
Minor tweak to M204 code (PR#2457)
2015-07-16 16:35:13 -05:00
Scott Lahteine
81d42406b7
Move braces in homeaxis to prevent a hanging else (PR#2451)
2015-07-16 10:25:54 -05:00
Scott Lahteine
552a327df8
Fix lsDive filename stack overrun (PR#2449)
2015-07-16 10:23:56 -05:00
AnHardt
a6628f12cc
Eliminate the further use of the pin-parameter
2015-07-15 20:50:58 -05:00
AnHardt
8504992e9f
Remove the additional pin variable in Servo.cpp
...
as sugested by @c-born
inhttps://github.com/MarlinFirmware/Marlin/issues/1885#issuecomment-92618240
2015-07-15 20:50:58 -05:00
AnHardt
ed6598adf5
Corrected Bed Height vs. Bed Topology for verbosity > 3
...
and cleaned out some tabs.
Everything else is a rebased PR#2017 as proposed by @CptanPanic
2015-07-15 19:51:40 -05:00
brian
62302ceb9e
Add calculation of difference between auto-correct bed level plane, and measured topo map.
2015-07-15 19:51:40 -05:00
Scott Lahteine
de25a48dec
Remove PID examples from preconfigured configs
2015-07-15 19:13:53 -05:00
Scott Lahteine
7456710a1f
Update configs formatting
2015-07-15 19:13:47 -05:00
Scott Lahteine
391386dd94
Update configs for new servo deactivation
2015-07-15 19:13:40 -05:00
AnHardt
5243d8b523
Deactivate DEACTIVATE_SERVOS_AFTER_MOVE by default
2015-07-15 17:39:43 -05:00
AnHardt
49609f6c14
Activate the new servo.move() function
...
by replacing the sequences (attach, write, delay, detach), and their conditions with the new function in Marlin.main.cpp
and removing the old configuration in the ABL part of Configuration.h
2015-07-15 17:39:43 -05:00
AnHardt
40b6edcad7
Introduce DEACTIVATE_SERVOS_AFTER_MOVE in Configuration.h
...
DEACTIVATE_SERVOS_AFTER_MOVE is ought to replace PROBE_SERVO_DEACTIVATION_DELAY.
But it will work on all servo moves, not only the probe servo moves.
2015-07-15 17:39:43 -05:00
AnHardt
2ddb2a2be9
Add Servo::move() to servo.cpp
...
move(pin, angel) - Sequence of attach(pin), write(angel),
if DEACTIVATE_SERVOS_AFTER_MOVE is defined waits SERVO_DEACTIVATION_DELAY, than detaches.
As we have jitter on the servos during moves of the steppers, and detaching them improves this behaviour,
the usual sequence to handle a servo movement is:
attach(pin)
write(angel)
delay(until the servo finished the move)
detache()
Here a function to handle the complete sequence.
2015-07-15 17:39:43 -05:00