Scott Lahteine
4b204da3c1
Cleanup of pins_RAMPS_13.h
2015-07-09 11:36:46 -05:00
Scott Lahteine
536f86e896
RigidBot CONTROLLERFAN_PIN in Configuration_adv.h
2015-07-09 11:36:46 -05:00
Scott Lahteine
f068e46661
RigidBoard include for pins.h
2015-07-09 11:36:46 -05:00
Scott Lahteine
9ebcae496d
RIGIDBOARD / RIGIDPANEL
2015-07-09 11:36:46 -05:00
Scott Lahteine
c3c605c658
Move note about LiquidTWI2 to Configuration.h (PR#2406)
2015-07-09 05:33:17 -05:00
Scott Lahteine
4e9d658141
Prevent a hanging SERIAL_ECHO_START in M111
2015-07-07 06:59:10 -05:00
Scott Lahteine
bc0fdbe88e
Use SERIAL_EOL in SERIAL_PROTOCOLLN macros
2015-07-07 06:59:10 -05:00
Scott Lahteine
d78ebbc0e9
Remove unused MSG_OK_B and MSG_OK_T
2015-07-07 06:59:10 -05:00
Scott Lahteine
6b494c1535
Use disable_all_heaters in M111
2015-07-07 06:59:10 -05:00
Scott Lahteine
15190d40df
Add extra EOL after M111
2015-07-07 06:59:10 -05:00
AnHardt
0e1cf78f5c
Remove code for testing if probing range is too small (PR#2390)
...
becaue it is over-restrictive and superseeded by the now working tests
if the probe-recktangle can be reached. See iss#2366
2015-07-07 06:58:01 -05:00
AnHardt
d421f5250d
Correct the sign of zprobe_zoffset for G29 (PR#@391)
...
Sign flipped with #2167 .
See also comments
https://github.com/MarlinFirmware/Marlin/issues/2040#issuecomment-118568355
and following.
2015-07-07 06:55:33 -05:00
Scott Lahteine
52fcc743ab
Replace "target" with "destination" in M600 (PR#2374)
...
- Also fix a bug in `M600` where `Z_MAX_ENDSTOP_INVERTING` is being
used as the index into the `destination[AxisEnum]` array.
2015-07-04 05:55:25 -05:00
Scott Lahteine
a5033c3652
Enable LCD_PIN_RESET if it exists (PR#2375)
2015-07-04 05:53:22 -05:00
AnHardt
23c8c5348f
Z-height fix V2b (PR#2351)
...
here the other two occurences of `Z_PROBE_OFFSET_FROM_EXTRUDER` are
replaced with `zprobe_zoffset`.
2015-07-02 20:30:40 -05:00
Todd Swindoll
a111fbbd0a
z-probe offset fix (PR#2361)
...
verified via 1.0.2 tag that compiles by multiple people,
credit for the fix goes to paulusjacobus for the initial find and
sniffle for the correction so M851 works.
2015-07-02 20:28:07 -05:00
Scott Lahteine
42465ee444
Cleanup of comments & spacing
2015-06-28 08:20:28 -05:00
Scott Lahteine
9682ed455e
Fix comment on M83, add comment to prepare_move
2015-06-28 08:20:19 -05:00
Scott Lahteine
bb44fe17cf
Fix typo in buzzer.h endif (PR#2337)
2015-06-27 06:10:19 -05:00
AnHardt
36746143a1
Correct output of M48 (PR#2336)
...
n_samples is an uint8_t .
Got printouts like:
50 of 2 ...
2015-06-27 06:08:40 -05:00
Scott Lahteine
f6ca5a8da8
Allow "M110 N123" without a checksum
2015-06-26 18:13:54 -05:00
Scott Lahteine
aaad65ff5d
Include a comment documenting M110
2015-06-26 18:13:54 -05:00
Scott Lahteine
862c72b030
Put the mandatory test of gcode_N first
2015-06-26 18:13:54 -05:00
Scott Lahteine
30976f9773
Allow M110 to handle a second N argument
2015-06-26 18:13:53 -05:00
Scott Lahteine
d135b15bb8
Init all endstop bits to 0 (PR#2332)
2015-06-26 07:10:22 -05:00
Scott Lahteine
5ccb1c9e7d
Use millis for M600 audio feedback interval
2015-06-25 20:45:03 -05:00
Scott Lahteine
fb16a83b8a
Cleanup M600 documentation comments
2015-06-25 20:45:03 -05:00
Scott Lahteine
97ec224d72
Replace target with destination in M600
2015-06-25 20:45:03 -05:00
Scott Lahteine
4ce9ddbb74
Check the temperature before filament change
2015-06-25 20:45:03 -05:00
Jaime van Kessel
b8b5762e55
Update Ultimaker URL
2015-06-25 09:12:44 -05:00
Jaime van Kessel
d5bfbf5a59
Added correct dutch translation for calibrate.
2015-06-25 09:12:44 -05:00
Scott Lahteine
149c474e55
Updated Russian language (PR#2325)
...
Gleaned from
https://github.com/MarlinFirmware/Marlin/commit/4ac14a7e5fa8e6e395436664
8976eafd1ae220ae
2015-06-22 23:07:19 -04:00
AnHardt
722829b058
Move buzzing code to buzzr.h & buzzer.cpp (PR#2307)
...
at least the lcd independent part from Marlin_main.cpp.
2015-06-22 22:31:48 -04:00
AnHardt
c461975140
Rename and repair MELZI_1284 (PR#2301)
...
to MELZI_MAKR3D.
Fix for #2288
As the normal MELZI also can have a 1284.
2015-06-22 22:30:07 -04:00
schlotzz
1e9cf905c7
Enable ZigZag AutoBedLeveling on Deltas (PR#2273)
...
ZigZag has been disabled by fault due to do_topography_map
2015-06-15 20:26:25 -05:00
Scott Lahteine
ec93383ec8
Add SanityCheck for bed probe position settings (PR#2282)
2015-06-15 20:22:44 -05:00
Scott Lahteine
dc40a5f6e0
Patch up more outdated config lines
2015-06-15 20:20:32 -05:00
Scott Lahteine
98c9111a7d
Update delta configs with latest settings
2015-06-15 20:20:32 -05:00
Scott Lahteine
e6baf8afd9
Fix up allen key settings in delta configs
2015-06-15 20:20:31 -05:00
Scott Lahteine
3b293fc5d1
Move Delta settings lower in delta files
2015-06-15 20:20:31 -05:00
Scott Lahteine
df21857583
Move extruder offset settings next to extruders setting
2015-06-15 20:20:31 -05:00
Scott Lahteine
2dd1859247
Cleanup spaces and comments in configs and conditionals
2015-06-15 20:20:31 -05:00
Scott Lahteine
a274769f4f
Clean up spacing and comments
...
Also clean up some trailing spaces in a few other sources
2015-06-15 20:20:31 -05:00
Scott Lahteine
d3bce05d54
Fix up spacing for filament sensor values
2015-06-15 20:20:31 -05:00
Scott Lahteine
b4b10a57fe
Fix configurator section directives and values lists
2015-06-15 20:20:31 -05:00
Scott Lahteine
bba14dcbe6
Move Z Safe Homing point to the middle of the movement range
2015-06-15 20:20:31 -05:00
Scott Lahteine
318318b02f
Add pins_RAMPS_13_EFB.h to reduce redundancy
2015-06-15 20:17:09 -05:00
Scott Lahteine
346c8b339b
Remove a test from pins_RAMPS_13.h
...
- Add 3 new lines to `pins.h` to remove 2 redundant tests in
`pins_RAMPS_13.h`
2015-06-15 20:15:38 -05:00
AnHardt
b93cddfcc9
Add lost MKS_BASE to pins.h (PR#2297)
2015-06-15 10:23:46 -05:00
AnHardt
6ab7b560af
Rework buzzing (PR#2296)
...
by:
Moving HAS_LCD_BUZZ macro to Coditionals.h
Renaming HAS_LCD_BUZZ to HAS_BUZZER to make clear is has nothing to do with the lcd.
Removing the ULTRALCD condition.
Moving declaration of lcd_buzz() out of the ULTRA_LCD block in ultralcd.h
Moving definition of lcd_buzz() out of the ULTIPANEL block in ultralcd.cpp
Renaming lcd_buzz() to buzz() to make clear is has nothing to do with the lcd.
All buzzing code is now only dependent on the existence of a BEEPER-pin or the definition of a LCD_USE_I2C_BUZZER.
To do: Check the conditions for the BEEPER-pin in all pin-files.
2015-06-15 06:13:26 -05:00
Scott Lahteine
29122db2fa
Fix ULTRA_LCD spelling in HAS_LCD_BUZZ
2015-06-15 06:12:34 -05:00
Scott Lahteine
1d94d098bf
Formatting tweaks as part of fixing issue 1497
2015-06-14 19:57:27 -05:00
Scott Lahteine
e602c28ad9
Set auto fan pins to OUTPUT during init
...
Fixes the problem of these pins being left in INPUT state, as described
in #1497
2015-06-14 19:57:27 -05:00
Scott Lahteine
90f858aa85
Use translated strings for axis movement (PR#2280)
...
Suggest we use the translated strings here. They use (except for
German) the phrasing “Move X” instead of just the axis letter, but they
should fit the available space. The “Extruder” string would be the
same, except it will be translated.
2015-06-14 08:16:00 -05:00
Scott Lahteine
e2a4a83586
Don't re-apply Z_RAISE_BETWEEN_PROBINGS in probe_pt (PR #2281 )
2015-06-12 22:39:35 -05:00
Scott Lahteine
6b1b3adaf0
Consistent punctuation in SanityCheck errors (PR#2283)
2015-06-12 09:31:02 -05:00
MagoKimbra
eb81982fcd
Fix error next command in autotune (PR#2274)
...
Now send only temperature for T or B, but not send OK.
Host interprets the line to show the right temperature, but not in
response to M105 then stop and send commands until it ends the autotune.
2015-06-12 07:10:38 -05:00
AnHardt
55b23c896a
Optimise out_of_range_error() (PR#2265)
...
by avoiding the strncopy()
2015-06-12 02:20:40 -05:00
filipmu
b0860adab6
Fix volumetric multiplier display for filament sensor (PR#2264)
...
The volumetric multiplier display needs to be multiplied by 100 in order to make it an integer for display purposes.
2015-06-12 02:19:27 -05:00
AnHardt
45642b7fe8
Respect DISABLE_AXIS settings (PR#2216)
...
when DEFAULT_STEPPER_DEACTIVE_TIME is over
instead of simply turn off all.
2015-06-11 11:35:05 -05:00
wurstnase
c85a486445
make the dual z-endstop optional (PR#2277)
...
it's disabled by default
2015-06-10 15:45:59 -05:00
Scott Lahteine
962b107341
Prevent current_command_args from bypassing nul (PR#2270)
2015-06-09 16:07:10 -05:00
Richard Wackerbarth
06ae832276
Deprecate Support for Arduino IDE < 1.0.5
...
Note that newer versions of the IDE can still
be made to support compilation for the older boards.
2015-06-08 17:15:28 -05:00
Scott Lahteine
ff6081be3a
Parse N[0-9]+[ ]* differently (PR #2263 )
...
More general solution to skip N[0-9]+[ ]* in the parser as in #2218
2015-06-08 17:06:49 -05:00
Scott Lahteine
aad121864e
Include "Z" in M851 report
2015-06-08 05:09:27 -05:00
Scott Lahteine
96a3fba8ac
Reverse the sign of zprobe_zoffset
...
- When editing on the LCD, minus now means below the nozzle
- Stores the opposite sign in EEPROM, so bumped to “V20”
2015-06-08 05:09:27 -05:00
fmalpartida
f92907183c
Updated SAV MkI pin header.
2015-06-08 05:07:11 -05:00
Richard Wackerbarth
58941e543e
ELB_FULL_GRAPHIC_CONTROLLER_SDCARDDETECTINVERTED removed
...
#defining something just to define something else doesn’t
make sense
If you want SDCARDDETECTINVERTED, just define it yourself.
If the previous code was intended to define, undefined and then again define the term, that code is improper.
2015-06-06 21:44:59 -05:00
CONSULitAS
788eb6e647
planner.cpp: remove tab
...
planner.cpp: single evil and hidden tab removed ♻️ 😏
2015-06-06 20:13:56 -05:00
CONSULitAS
3a5963c0e7
Configuration_adv.h: Add FAN_MIN_PWM for slow fan stopping issue …
...
* all Configuration_adv.h: Add #define FAN_MIN_PWM for slow fan stopping
issue
* for K8200: uncommented with tested (and working) values
2015-06-06 20:13:56 -05:00
CONSULitAS
e55e65d1e4
planner.cpp: Add FAN_MIN_PWM for slow fan stopping issue …
...
@CONSULitAS
planner.cpp: Add FAN_MIN_PWM for slow fan stopping issue (V2.1 with
macro and linear scaling)
@thinkyhead thanks for idea on linear scaling
2015-06-06 20:13:56 -05:00
paclema
8d295547be
* Auto filament change on CHANGEFILAMENT feature. Now you can activate this option that extrude filament until you press the button.
2015-06-06 19:45:45 -05:00
atfield90
6d0e91328d
Renamed Board_megatronics_1 to Board_minitronics
2015-06-06 18:59:04 -05:00
atfield90
c4a2e5ac23
Renamed Pins_megatronics_1 to Pins_minitronics
2015-06-06 18:59:04 -05:00
atfield90
2076906aaa
Renamed Pins_megatronics_1 to Pins_minitronics
2015-06-06 18:59:04 -05:00
tonokip
10733a2bb0
added minirambo pin definitions. V2
2015-06-06 18:37:58 -05:00
Richard Wackerbarth
303d47228e
Define Probe Path in new format
2015-06-06 17:48:27 -05:00
Richard Wackerbarth
ad09d6a60f
3 Step Allen Key Probe
2015-06-06 17:48:27 -05:00
Richard Wackerbarth
8359cdf01d
Check compatibility for Teensy-based processor
...
The instruction say to set a #define in fastio.h
However, that value is not included before this test.
2015-06-06 17:24:34 -05:00
Ed Boston
08968c29bb
Adding ELB_FULL_GRAPHIC_CONTROLLER_SDCARDDETECTINVERTED to Examples
2015-06-06 16:40:32 -05:00
Ed Boston
fed18bcc20
Removed SDSLOW for ELB_FULL_GRAPHIC_CONTROLLER
...
Hardware changes has removed the need for this option.
2015-06-06 16:40:32 -05:00
Ed Boston
b94a0e1501
Added ELB_FULL_GRAPHIC_CONTROLLER_SDCARDDETECTINVERTED
...
The new define allows the sd card detect to be inverted or not from
Configuration.h
2015-06-06 16:40:31 -05:00
Ed Boston
bc205c76a3
SDCARDDETECTINVERTED problems
...
Fixed an error where SDCARDDETECTINVERTED was being defined/undefined
improperly
2015-06-06 16:40:31 -05:00
AnHardt
e400fce271
Merge pull request #2221 from MagoKimbra/Dryrun
...
Insert Debug DRYRUN Repetier Host compatible
2015-06-03 12:30:48 +02:00
AnHardt
163a9ff58e
Merge pull request #2230 from AnHardt/psm
...
Fix thermal protection state machine target temp. V2
2015-06-03 09:46:53 +02:00
AnHardt
c3fe6e61ae
Merge pull request #2229 from AnHardt/position-out-of-range
...
Fix out_of_range_error()
2015-06-03 09:46:22 +02:00
MagoKimbra
4db8d2def4
Moved MSG_DEBUG in language.h
2015-06-03 08:18:27 +02:00
AnHardt
b7e9ba7591
Back to 1.0.3 dev - for now
2015-06-03 00:47:11 +02:00
AnHardt
d1f4471000
Merge pull request #2146 from Wackerbarth/Versioning
...
Versioning
2015-06-02 18:31:21 +02:00
AnHardt
b1404a0743
fix thermal protection state machine target temp. V2
...
If the target temperature is changed then it would always stay in the reset state.
Thanks to @tonokip.
Replaces #2119
2015-06-02 12:26:21 +02:00
AnHardt
17b0ec84ed
Fix out_of_range_error()
...
For sprintf_P() the first parameter has to be a `char*` not `const char*`.
2015-06-02 11:50:32 +02:00
AnHardt
35af5ef23e
Merge pull request #2225 from Wurstnase/naming
...
consistency name for multiplier
2015-06-02 10:18:22 +02:00
wurstnase
e7e964432b
consistency name for multiplier
...
replace extruder_multiply with extruder_multiplier
like feedrate_multiplier or volumetric_multiplier
2015-06-01 22:33:22 +02:00
AnHardt
d4c6fc5d0a
Merge pull request #2223 from AnHardt/dualz-semicolon
...
Add a semicolon to make Z_DUAL_STEPPER_DRIVERS compile again.
2015-06-01 20:15:55 +02:00
AnHardt
0d9d21d15f
Add a semicolon to make Z_DUAL_STEPPER_DRIVERS compile again.
2015-06-01 19:51:43 +02:00
MagoKimbra
76306f9073
Insert Debug DRYRUN Repetier Host compatible
2015-06-01 18:34:45 +02:00
MagoKimbra
881146bc22
Fix problem Width Cura
2015-06-01 17:25:32 +02:00
fmalpartida
11e3f3375d
Merge commit '764e61708b8e73410c7819d59c4970d7089ca6f5' into bugFixing
...
Updated LCD wiki location.
2015-05-31 21:20:26 +02:00
Alexey Shvetsov
a8670b66a7
Update ru translation
...
Signed-off-by: Alexey Shvetsov <alexxy@gentoo.org>
2015-05-31 20:09:10 +03:00
fmalpartida
93da52d011
Added support for OLED SSD1306 I2C based LCDs.
2015-05-31 18:53:29 +02:00
Wurstnase
9c09967803
Merge pull request #2149 from Wurstnase/enstop_bits
...
faster compare
2015-05-31 16:02:55 +03:00
wurstnase
0f3f7d6835
clean up double endstops
2015-05-31 14:06:13 +02:00
AnHardt
9d2a980bcf
Merge pull request #2170 from thinkyhead/beep_M600_elsewise
...
Slight size reduction by adding idle()
2015-05-30 12:42:32 +02:00
AnHardt
2728dc0606
Merge pull request #2194 from thinkyhead/reduce_strings
...
Redo "invalid extruder" to save 304 bytes
2015-05-30 11:05:08 +02:00
Scott Lahteine
be5236e839
Reduce setTargetedHotend by removing the switch
2015-05-29 18:03:58 -07:00
Scott Lahteine
06f401e7e5
Redo "invalid extruder" to save 264 bytes
...
- Use `setTargetedHotend` in `M200`, as with other commands that use
`T` for the extruder
- Synthesize the "invalid extruder" message, obviating several long
strings
2015-05-28 22:25:28 -07:00
Scott Lahteine
1a882bcc2e
Merge pull request #2193 from thinkyhead/ignore_unrecognized_commands
...
Ignore unknown commands if they start with G, M, or T
2015-05-28 22:03:48 -07:00
Scott Lahteine
a672872717
Merge pull request #2187 from AnHardt/MAX6675M105
...
Print active extruder with M105 for MAX6675
2015-05-28 18:12:48 -07:00
Scott Lahteine
9beed830eb
Drop commented code_is_good lines
2015-05-28 17:53:47 -07:00
Scott Lahteine
068d4a1eb2
Ignore unknown commands if they start with G, M, or T
2015-05-28 17:44:09 -07:00
Scott Lahteine
5824f613ff
Merge pull request #2185 from jothan/bed_integral
...
Separate the maximum integral power for the bed from PID_INTEGRAL_DRI…
2015-05-28 16:32:02 -07:00
Scott Lahteine
c5c9d12630
Merge pull request #2183 from AnHardt/displayinit
...
Initialize the display earlier
2015-05-28 16:29:18 -07:00
Scott Lahteine
ef4becc413
Merge pull request #2188 from AnHardt/FtoN
...
Replace MSG_F? with MSG_N?
2015-05-28 16:18:50 -07:00
Scott Lahteine
0564625757
Update M33 for new gcode parser
2015-05-28 14:17:39 -07:00
AnHardt
f18f689c01
Replace MSG_F? with MSG_N?
...
To avoid double definitions.
I prefer to read N for Number not for Nozzle.
2015-05-28 20:30:23 +02:00
AnHardt
af7e3f5076
Print active extruder with M105 for MAX6675
...
Was omitted when T0 is a MAX6675.
2015-05-28 19:03:16 +02:00
Jonathan Bastien-Filiatrault
d46d9d998e
Add maximum bed integral term in example configurations.
2015-05-28 12:51:37 -04:00
Jonathan Bastien-Filiatrault
e86f2342c0
Separate the maximum integral power for the bed from PID_INTEGRAL_DRIVE_MAX / PID_MAX.
...
My PID_INTEGRAL_DRIVE_MAX was at 96, which was insufficient for my bed
to reach its intended temperature. The head requires a low maximum power since
I run on 24 volts and it has a somewhat low thermal mass.
2015-05-28 11:48:04 -04:00
AnHardt
f0523b5816
Initialize the display earlier
...
to have it ready to display errors during (temperature)-setup.
2015-05-28 16:08:17 +02:00
Scott Lahteine
790c697c19
Fix DEGREES macro
2015-05-28 00:19:48 -07:00
Scott Lahteine
76b4678f99
Merge pull request #2171 from thinkyhead/gcode_110_is_good
...
M110 is a known command
2015-05-26 21:17:58 -07:00
Scott Lahteine
03d5709b09
M110 is a known command
...
- The command parser now displays “unknown command” in more cases.
Known commands must be added to the `switch` inside `process_commands`
to suppress the error.
2015-05-26 20:31:18 -07:00
Scott Lahteine
d76a01194d
Slight size reduction by adding idle()
2015-05-26 20:08:21 -07:00
Richard Wackerbarth
2deb5a8ac5
Temporary Hack
...
REVERT THIS CHANGE
In proper use, we want to force the vendor to update this file to reflect distribution parameters
However, until most users have converted to automatic versioning,
we “grant them a pass”
2015-05-25 15:54:08 -05:00
Richard Wackerbarth
b5743d6927
Use SOURCE_CODE_URL rather than FIRMWARE_URL
2015-05-25 15:53:34 -05:00
Richard Wackerbarth
5ea139fd79
Revised Versioning mechanism
2015-05-25 15:53:14 -05:00
AnHardt
da246f5cb1
Activate BED_MINTEMP error.
...
And call _temp_error() directly for ERR_MAXTEMP_BED to avoid the only one time use of bed_max_temp_error().
Includes #2156 .
2015-05-25 13:23:19 +02:00
AnHardt
959da98d8e
Call kill() only once when triggered by a temperature error
...
to avoid stack overflow when called from interrupt.
Some clean up for calls of disable_all_heaters().
'disable_all_heaters()' is called in kill() and again when 'killed' is already set inside _temp_error().
2015-05-25 12:44:03 +02:00
Scott Lahteine
68f6f149d0
Reduce code size with out_of_range_error function
...
- Affects code size when automatic bed leveling is enabled
2015-05-24 20:18:02 -07:00
wurstnase
94120740d8
faster compare
...
!(~(ab)&0x3) and ab == 0x3 are equal
2015-05-23 07:55:15 +02:00
Scott Lahteine
c9141e604a
Merge pull request #2145 from thinkyhead/gcode_folding
...
Indentation in process_commands
2015-05-22 18:47:37 -07:00
Scott Lahteine
b55f8718c3
Indent G90/G91, G92
2015-05-22 17:34:08 -07:00
Scott Lahteine
b0d520b109
Indent G30, G31/G32
2015-05-22 17:33:17 -07:00
Scott Lahteine
ffe27a6225
Indent G29
2015-05-22 17:32:46 -07:00
Scott Lahteine
86083badc2
Indent G4, G10/G11, G28
2015-05-22 17:32:27 -07:00
Scott Lahteine
47d7a9cb5e
Indent G2/G3
2015-05-22 17:31:38 -07:00
Scott Lahteine
350f239d84
Indent G0/G1
2015-05-22 17:31:24 -07:00
Scott Lahteine
672b0c1fd3
Cleanup pins in RAMPS_13_EFB boards
2015-05-22 16:20:54 -07:00
Scott Lahteine
15a2351675
No need for +1 on initial seen_pointer
2015-05-22 15:31:30 -07:00
Scott Lahteine
550dd87b2a
Set seen_pointer before calling code_value
2015-05-22 15:11:48 -07:00
Scott Lahteine
38cc0b93c6
Merge pull request #1874 from AnHardt/Bulgarian
...
Introduction of Bulgarian - language_bg.h
2015-05-22 13:59:50 -07:00
Scott Lahteine
04a1622172
Merge pull request #2127 from Wackerbarth/Kossel_Pro
...
Kossel Pro
2015-05-21 18:43:26 -07:00
Scott Lahteine
81c2ca3e10
Merge pull request #2131 from thinkyhead/bq_is_ramps_13_efb
...
Witbox and Hephestos are RAMPS EFB
2015-05-21 18:39:02 -07:00
Scott Lahteine
f919a2fed1
Merge pull request #2134 from AnHardt/preheat-all
...
Shift call of start_watching_heater() into setTargetHotend()
2015-05-21 18:36:28 -07:00
Scott Lahteine
063881b5bd
Fix a couple of doubled semicolons
2015-05-21 18:15:29 -07:00
AnHardt
94dff5b36a
Merge pull request #2137 from thinkyhead/tweak_swh
...
Move millis call in start_watching_heater
2015-05-22 02:02:07 +02:00
Scott Lahteine
70d2f48d4e
Merge pull request #2136 from thinkyhead/M303_suppress_error
...
Suppress the line mismatch error after M303
2015-05-21 16:46:30 -07:00
AnHardt
0c0ace2a04
Remove start_watching_heater() fom M104 and M109
2015-05-22 01:44:50 +02:00
Scott Lahteine
00716d0ca0
Small start_watching_heater adjustment
2015-05-21 16:44:49 -07:00
Scott Lahteine
834747deb7
Merge pull request #2135 from Wurstnase/new_endstop_bits
...
new endstop bits
2015-05-21 16:35:54 -07:00
Scott Lahteine
bde9c70d42
Suppress the line mismatch error after M303
2015-05-21 16:27:22 -07:00
Scott Lahteine
50bd7493cc
Merge pull request #2108 from thinkyhead/m33_long_filename_host_support
...
M33 LONG_FILENAME_HOST_SUPPORT
2015-05-21 16:22:47 -07:00
Scott Lahteine
4d11b29959
Merge pull request #2113 from thinkyhead/command_sanitizer
...
Command sanitizer
2015-05-21 16:21:58 -07:00
wurstnase
ff98b8632b
new endstop bits
2015-05-21 23:16:43 +02:00
AnHardt
9b0fa9c309
Changed dependency of start_watching_heater() in setTargetHotend() to THERMAL_PROTECTION_HOTENDS
2015-05-21 21:07:37 +02:00
AnHardt
bc0764894a
Shift call of start_watching_heater() into setTargetHotend()
...
to warrant watching is set or reset.
Make setTargetBed() in _lcd_preheat() dependant of TEMP_SENSOR_BED.
Use disable_all_heaters() in lcd_cooldown() and abort_on_endstop_hit.
2015-05-21 20:36:11 +02:00
Richard Wackerbarth
b878bc5620
Introducing the Kossel Pro Build Configuration
2015-05-21 11:47:34 -05:00
Richard Wackerbarth
1d8f61ca8a
AT90USB is defined in pins.h
2015-05-21 11:46:54 -05:00
Richard Wackerbarth
735bf2d35f
Describe Custom M Code
2015-05-21 08:06:33 -05:00
Scott Lahteine
f39658c822
M120 and M121 are reversed
2015-05-21 00:17:44 -07:00
Scott Lahteine
6eb4f90ce7
Also synchronize configurator copies of configs
2015-05-20 21:34:00 -07:00
Scott Lahteine
9d1961ebe3
Witbox and Hephestos are just RAMPS_13_EFB
2015-05-20 21:33:23 -07:00
AnHardt
4422365a53
Merge branch 'Development' of https://github.com/MarlinFirmware/Marlin into _temp_error
2015-05-20 23:34:39 +02:00
AnHardt
4113762062
Merge pull request #2130 from AnHardt/kill2
...
Add a string parameter to kill()
2015-05-20 23:32:51 +02:00
AnHardt
89d2ee6f13
Make output on display dependant of ULTRA_LCD
2015-05-20 22:03:16 +02:00
AnHardt
120d4c7a8c
Merge remote-tracking branch 'origin/kill2' into _temp_error
2015-05-20 21:25:32 +02:00
AnHardt
cb6e82dc60
Change from kill() to kill(const char *)
...
in temperature.cpp
2015-05-20 21:22:48 +02:00
AnHardt
9d13942278
Use new kill() with parameter.
2015-05-20 21:18:52 +02:00
AnHardt
6398c5e28d
Merge remote-tracking branch 'origin/kill2' into _temp_error
2015-05-20 21:08:19 +02:00
AnHardt
f4a93ed997
Add a string parameter to kill()
...
Makes the output on the LCD adjustable.
2015-05-20 20:53:48 +02:00
AnHardt
2990c6c45f
Use new kill_() for _temp_error()
...
instead of stop(). We really want to require a reset and no chance to set a new temperature.
2015-05-20 14:03:14 +02:00
AnHardt
9b8c6ed254
Merge pull request #2120 from chris-bo/dogm_config
...
move dogm font selection to configuration_adv.h
2015-05-20 10:11:34 +02:00
AnHardt
06513565e9
Merge pull request #2105 from eboston/Development
...
Add ELB_FULL_GRAPHIC_CONTROLLER with ADAFRUIT_ST7565 display.
2015-05-20 09:56:21 +02:00
Ed Boston
082ed3beed
Propagate Configuration.h changes
...
Updated all the example Configuration.h files for the new display type.
2015-05-19 14:04:57 -07:00
Ed Boston
152b681bb5
Added link to controller github
...
Added the link to the github information about the
ELB_FULL_GRAPHIC_CONTROLLER
2015-05-19 04:14:55 -07:00
AnHardt
995b84944b
Merge pull request #1982 from CONSULitAS/Development_Update_language.h
...
language.h: update documentation / URL für K8200
2015-05-19 12:13:35 +02:00
Scott Lahteine
7bc5fd8193
Merge pull request #2123 from AnHardt/Duemilanove
...
Remove Duemilanove
2015-05-18 20:36:05 -07:00
Scott Lahteine
94de1e0d93
Merge pull request #2116 from AnHardt/wording
...
transpire -> expire
2015-05-18 20:34:46 -07:00
AnHardt
4d4fa3607b
Remove Duemilanove
...
No way to fit Marlin into 32K.
2015-05-19 02:46:37 +02:00
AnHardt
e353d27430
Merge branch 'Development' of https://github.com/MarlinFirmware/Marlin into Bulgarian
2015-05-18 23:56:53 +02:00
Ed Boston
ca8d1756d5
Define fixes
...
Fixed a couple defines that were not changed or commented out.
2015-05-18 14:23:31 -07:00
CONSULitAS
b96b28b7cc
language.h: update documentation for LANGUAGE_INCLUDE
...
language.h: update documentation for LANGUAGE_INCLUDE
@thinkyhead What do you think? I think there should be a warning like
this.
2015-05-18 23:11:26 +02:00
Christian Bohn
258bcdefe0
move dogm font selection to configuration_adv.h
2015-05-18 22:54:53 +02:00
AnHardt
7750180c93
transpire -> expire
...
Minor wording correction.
2015-05-18 21:48:10 +02:00
AnHardt
70163dafb9
Use _temp_error() for all errors thrown by different mechanisms
...
Now ending in an endless loop.
Tidy up the output format.
We now get:
ERRORTEXT ", system stopped! Heater_ID: " HEATERID
Where ERRORTEXT can be:
"Heating failed"
"Thermal Runaway"
"MAXTEMP triggered"
"MINTEMP triggered"
and soon
"Thermal Jump"
HEATERID can be
0, 1, 2 ,3 , "bed"
This messages are always followed by the common:
"Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)"
2015-05-18 20:26:25 +02:00
Scott Lahteine
a0f362c735
Simplify & optimize with current_command_args
2015-05-18 07:08:04 -07:00
Scott Lahteine
adc8fcb77f
More parser comments, optimize code_seen, save with goto
2015-05-18 07:08:04 -07:00
Scott Lahteine
c6d8dd19d9
use fetched value
2015-05-18 07:08:04 -07:00
Scott Lahteine
1116e13f5a
Further optimization of command parser
2015-05-18 07:08:03 -07:00
Scott Lahteine
3a4c3ab76e
Pre-sanitize the command before handling
...
- Use a global pointer for the current sanitized command
- Pre-sanitize the current command to bypass `N` and nullify `*`,
removing the need for handlers to bypass, ignore, or nullify these
parts, and reducing overhead for `code_seen`, etc.
- Pre-skip leading whitespace.
- Only look for G, M, T codes at the start of the command.
- Verify that G, M, T codes are followed by command codes.
2015-05-18 07:06:51 -07:00
Ed Boston
a83bf18ee1
More functional seperation
...
Moved SDCARDDETECTINVERTED and SDSLOW to Conditionals.h.
Added U8GLIB_LM6059_AF to define display specific actions.
Added reminder to compile in u8glib
2015-05-18 05:37:46 -07:00
AnHardt
97ca1b3f4d
Name magic value 20 to MAX_OVERSHOOT_PID_AUTOTUNE
...
to make it better findable.
2015-05-18 14:15:29 +02:00
Scott Lahteine
0f2c9bacfd
M33 LONG_FILENAME_HOST_SUPPORT
2015-05-17 17:36:32 -07:00
Scott Lahteine
3feaef6526
Have G92 set the nozzle position on Delta and SCARA
2015-05-17 17:08:05 -07:00
Ed Boston
047e688e93
Changed ADAFRUIT_ST7565 to ELB_FULL_GRAPHIC_CONTROLLER
...
Rename of define to avoid confusion between the controller and the
display which had similar names.
2015-05-17 15:23:17 -07:00
Ed Boston
1999ac415c
Formatting Changes
...
Fixes for some code formatting changes and commenting out the
ADAFRUIT_ST7565 define that was left defined.
2015-05-17 13:39:24 -07:00
Ed Boston
41f8cdb3a6
ADAFRUIT_ST7565
...
Added support for new display type
2015-05-17 12:47:41 -07:00
wurstnase
21ff773832
rework out_bits
2015-05-17 14:33:09 +02:00
Scott Lahteine
6c27eaf864
Merge pull request #2101 from thinkyhead/code_style
...
Code style and a dangling "else"
2015-05-17 03:39:08 -07:00
Scott Lahteine
d580a0d186
Use "+=" in plane rotation
2015-05-17 01:51:14 -07:00
Scott Lahteine
2f3a410cb0
Fix a potential hanging "else" bug
2015-05-17 01:50:30 -07:00
Scott Lahteine
b83e3f0905
Combine "Bed X: " strings
2015-05-17 01:49:52 -07:00
Scott Lahteine
7dfb8becdb
Adjust some names and types in Marlin_main.cpp
2015-05-17 01:48:51 -07:00
Scott Lahteine
c966aa26ff
Comments in Marlin_main.cpp
2015-05-17 01:47:53 -07:00
Scott Lahteine
c54a2ea042
Adjust spacing in Marlin_main.cpp and stepper.*
2015-05-17 01:47:02 -07:00
Scott Lahteine
072625ccad
Update headings in Marlin_main.cpp and stepper.cpp
2015-05-17 01:44:53 -07:00
Scott Lahteine
16032f149f
Rename to codenum as a consistency
2015-05-16 23:17:35 -07:00
Scott Lahteine
273a4a253f
Merge pull request #2096 from thinkyhead/cherry_picking3
...
Hide M117 with no LCD
2015-05-16 21:10:28 -07:00
Scott Lahteine
64825a3d1e
Merge pull request #2095 from thinkyhead/cherry_picking2
...
Add gcode_line_error to reduce code size
2015-05-16 21:09:15 -07:00
Scott Lahteine
ca79282eaf
Hide M117 with no LCD
2015-05-16 20:59:04 -07:00
Scott Lahteine
ce218cafdb
Add gcode_line_error to reduce code size
2015-05-16 20:54:58 -07:00
Scott Lahteine
46d59784ad
Rename preocess_command to process_next_command
2015-05-16 20:47:40 -07:00
Scott Lahteine
513077c317
Minor change to fan kick
2015-05-16 19:42:28 -07:00
Scott Lahteine
76438195f0
NO_TIMEOUTS and ADVANCED_OK off by default
2015-05-16 02:47:20 -07:00
Scott Lahteine
d2563804c8
Add LF to file errors
2015-05-15 04:37:22 -07:00
Scott Lahteine
e114662cfa
Adjust SdBaseFile spacing
2015-05-15 03:23:49 -07:00
Scott Lahteine
98e91f5253
Allow lsDive to recurse with minimal stack usage
2015-05-15 03:19:07 -07:00
Scott Lahteine
19166a92e4
Merge pull request #2057 from Wurstnase/serial_wait
...
add plan buffer remaining for 'P' and block buffer remaining 'B'
2015-05-14 04:57:08 -07:00
Scott Lahteine
95f5a68006
Merge pull request #2074 from thinkyhead/lcd_xyz_unknown
...
Display unknown XYZ on the LCD as "---"
2015-05-14 04:56:38 -07:00
Scott Lahteine
e97fcafd0e
Merge pull request #2076 from thinkyhead/mendel_inverting
...
Use MSG_OK in M105
2015-05-14 04:54:11 -07:00
Scott Lahteine
0f6cd3640b
Drop extraneous ok_to_send
2015-05-14 04:38:09 -07:00
Scott Lahteine
0ce355d9e7
Use MSG_OK in M105
2015-05-14 03:33:38 -07:00
Scott Lahteine
a366e57385
Merge pull request #2075 from thinkyhead/mendel_inverting
...
Use Mendel default for INVERT_Y_DIR
2015-05-14 03:29:24 -07:00
Scott Lahteine
7b3acfbb6f
Merge pull request #2072 from thinkyhead/better_arc_code
...
Consolidate arc code, remove motion_control.*
2015-05-14 00:27:22 -07:00
Scott Lahteine
78beef2d73
Use Mendel default for INVERT_Y_DIR
2015-05-14 00:25:47 -07:00
Scott Lahteine
1a4a09c26f
Display unknown XYZ on the LCD as "---"
...
- Also show 2 digits past decimal for Z on DOGM
2015-05-13 22:45:58 -07:00
Scott Lahteine
68ce419147
Note on segment size
2015-05-13 19:11:36 -07:00
Scott Lahteine
8b92249f18
Bring arc_offset into auto scope
2015-05-13 19:00:46 -07:00
Scott Lahteine
80807b2d71
Consolidate arc code, remove motion_control.*
2015-05-13 18:52:41 -07:00
Scott Lahteine
f65833931d
Formatting tweaks
2015-05-13 02:02:19 -07:00
Scott Lahteine
fcfd99c1ae
Add comments to lcd_control_temperature_menu
2015-05-12 18:46:16 -07:00
Scott Lahteine
d693e0f378
Use WATCH_TEMP_INCREASE + TEMP_HYSTERESIS + 1 as difference limit
2015-05-12 18:30:38 -07:00
Scott Lahteine
6697a8f375
Watch the heater a little longer
2015-05-12 18:22:47 -07:00
Scott Lahteine
5693a6e3c9
Fix heating error message
2015-05-12 18:17:13 -07:00
Scott Lahteine
747fd5801c
Merge pull request #2055 from thinkyhead/thermal_unified
...
Combine thermal runaway and watch-period
2015-05-12 08:04:29 -07:00
Scott Lahteine
6e5572228d
Merge pull request #2064 from thinkyhead/wait_before_g28
...
Split up prepare_move by type
2015-05-12 07:53:11 -07:00
Scott Lahteine
27ad381e25
Allow fractional seconds in G4 and M0
2015-05-12 07:52:08 -07:00
Scott Lahteine
5146694452
Merge pull request #1884 from shaggythesheep/feature_new_board_ramps_cnc_controller
...
Feature: Add RAMPS CNC Controller Board
2015-05-12 04:31:49 -07:00
Scott Lahteine
b2bd9aae7c
SCARA_SEGMENTS_PER_SECOND
2015-05-12 04:18:15 -07:00
Scott Lahteine
bd20bd5444
Merge pull request #2063 from chris-bo/autobed_sled
...
improve sled handling
2015-05-12 03:29:21 -07:00
Scott Lahteine
9e95ceb3fc
Split up prepare_move by type
...
- For better encapsulation add inlines for each prepare_move type
- Move controllerFan vars inside the function as statics
- Some formatting cleanup
- Rename `ClearToSend` as `ok_to_send`
2015-05-12 02:08:20 -07:00
Scott Lahteine
9ba8cf5fe3
Merge pull request #2061 from thinkyhead/wait_before_g28
...
Always do st_synchronize() before G28
2015-05-12 02:05:30 -07:00
Scott Lahteine
873f7d6f2a
Check that configs are up-to-date
2015-05-12 01:33:51 -07:00
Christian Bohn
f48599f172
add pin definition to some motherboards
2015-05-12 10:02:23 +02:00
Scott Lahteine
b5200e184c
Remove extra setup_for_endstop_move
2015-05-12 01:01:53 -07:00
Scott Lahteine
8d814de558
Return void in prevent_dangerous_extrude
2015-05-12 00:55:00 -07:00
Scott Lahteine
367e2eb9f4
Global setup_for_endstop_move
2015-05-12 00:51:22 -07:00
Wurstnase
1d5677cc3b
add missing Z-bits
2015-05-12 09:36:19 +02:00
Wurstnase
df12e68e7d
add missing Z_PROBE-bit
2015-05-12 09:33:24 +02:00
Scott Lahteine
fa951f8a0b
Always do st_synchronize() before G28
2015-05-12 00:31:51 -07:00