Commit graph

583 commits

Author SHA1 Message Date
Roxy-3D
71df1f7f57
Don't display M421 information for UBL at startup
It takes too long to display the mesh data for large mesh's at startup.   We should consider ways to speed this up.
Perhaps it makes sense to display an entire row of the mesh instead of just one mesh point?
2018-07-17 17:19:52 -05:00
Giuliano
e5ea9d200f [2.0.x] fix kill printer (#11260)
This will fix kill message on dual printer with 0 alignment offset
2018-07-13 23:12:43 -05:00
Scott Lahteine
25e2ca8896 Add Z_CLEARANCE_MULTI_PROBE
Co-Authored-By: nightgryphon <ngryph@gmail.com>
2018-07-12 22:46:34 -05:00
Scott Lahteine
566d05006d report_state > event_handler
Make the endstop report method track endstop changes on its own.
2018-07-11 21:08:07 -05:00
Scott Lahteine
6b521b6df2 Loosen thermistor table size limit
Co-Authored-By: Aaron Griffith <aargri@gmail.com>
2018-07-11 21:08:07 -05:00
Scott Lahteine
63f4c9bdb9 Followup to float maths patch 2018-07-06 21:34:09 -05:00
Scott Lahteine
2992112da0 Optimize delta kinematics
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
2018-07-04 22:28:56 -05:00
etagle
1367df2875 Replace double with float, optimize calculation 2018-07-04 22:28:56 -05:00
Scott Lahteine
68e6650df7 Remove Quake Fast Inverse SQRT (it isn't faster) 2018-07-04 22:22:10 -05:00
Scott Lahteine
9c058091e9 No M914 or SGT set for non-sensorless axes 2018-07-03 20:09:13 -05:00
Scott Lahteine
568cfe7caa Add thermistor 501 (100K Zonestar) 2018-07-03 17:52:06 -05:00
Scott Lahteine
c51e27d11d
Do a hard kill for failed homing moves (#11161) 2018-06-30 21:54:07 -05:00
Scott Lahteine
90ba77ea0f Lose the old HOMEAXIS macro 2018-06-30 18:13:13 -05:00
Scott Lahteine
2421f3a47d Detect endstop hits in any direction 2018-06-30 17:27:37 -05:00
Scott Lahteine
8eaac0dab3
Add delta feedrate scaling (#11153) 2018-06-30 13:44:27 -05:00
Scott Lahteine
bd7f5848f1
Remove JUNCTION_DEVIATION_INCLUDE_E option (#11147) 2018-06-29 22:42:05 -05:00
Scott Lahteine
42f9921482 Ignore Z min endstop with separate Z-probe
To allow for the case where a Z endstop (e.g., hall effect) is higher than the probe trigger point, don't check the Z min endstop during probe moves. See #11134
2018-06-28 05:06:11 -05:00
Scott Lahteine
aa4cd2e861 Eliminate stepper.* signed/unsigned warnings 2018-06-27 23:10:51 -05:00
Eduardo José Tagle
edb21f349a Fix stepper/planner block handling, race conditions (#11098)
- Allow planner to alter the deceleration phase of the currently executing block.
- Remove BUSY flag, as it is NON ATOMIC to set bits in the Stepper ISR and Planner at the same time.
2018-06-27 18:11:16 -05:00
Scott Lahteine
4d3a9930c5 Match ASM comment spacing to 1.1.x 2018-06-27 17:26:48 -05:00
Scott Lahteine
053438a3aa
Poll all endstops, even when stationary (#11123) 2018-06-27 04:18:57 -04:00
Andy Shaw
3b3029c4bf Make max_e_jerk an array to reduce CPU usage (#11118) 2018-06-26 22:38:31 -04:00
Giuliano
8d8f257384 [2.0.x] Fix advanced pause init values (#11095)
Fixed for cycle used to initialize default values
2018-06-26 14:37:52 -04:00
etagle
5b49fccf80 Add stepper driver DIR delay configuration option
...and recommended pulse width configuration for A4988
2018-06-26 13:28:04 -05:00
etagle
fb4e0b105b Fix endstops compilation error 2018-06-25 12:10:17 -04:00
Eduardo José Tagle
48a15d1c7e [2.0.x] Fix stepper/planner race condition and Stepper pulse timer (#11081)
* Planner: Removal of some race conditions between Stepper ISR and Planner, some of them pointed out by @AnHardt, some of my own findings
* Fixing timing on stepper pulses adding a compensation for the non-null time required to set ports.
2018-06-22 09:15:37 -05:00
Scott Lahteine
50b6204079 Fix LIN_ADVANCE max_e_jerk_factor
According to https://github.com/MarlinFirmware/Marlin/issues/9917#issuecomment-399204568
2018-06-21 22:02:34 -04:00
Scott Lahteine
99591dc20c
Filter endstops state at all times (#11066) 2018-06-21 20:14:16 -05:00
Scott Lahteine
7406f04029 Use MAX (not max) in stepper.h 2018-06-19 20:51:07 -05:00
Scott Lahteine
da94e0bd27 Unsigned eeprom mesh addresses 2018-06-15 15:51:57 -05:00
Scott Lahteine
4c8d6df13c
Extra insurance against endstop false positives (#11013) 2018-06-13 01:22:02 -05:00
Scott Lahteine
81edbfa665
Merge pull request #11004 from ejtagle/always_honor_maximum_step_rate
[2.0.x] Fix stepper pulse minimum period and timing calculations
2018-06-12 22:17:22 -05:00
Scott Lahteine
f3fed52348 Fix coolstep_min_speed / sensorless homing
Fix #8890
2018-06-12 22:12:46 -05:00
etagle
a215725df6 Fix stepper pulse timing
Always honor minimum period on stepper pulse generation, and fix timing calculations

Signed-off-by: etagle <ejtagle@hotmail.com>
2018-06-12 21:34:24 -05:00
Scott Lahteine
0d79128c8d Localize stepper-specific defines 2018-06-12 21:16:54 -05:00
Scott Lahteine
4dbec774b5 HAL_*_TIMER_RATE => *_TIMER_RATE 2018-06-12 16:39:12 -05:00
Scott Lahteine
9d04f47d98 Improvements for junction_deviation_mm
- Drop `max_jerk` with `JUNCTION_DEVIATION`
- Add `max_e_jerk_factor` for use by `LIN_ADVANCE`
- Recalculate `max_e_jerk_factor` when `junction_deviation_mm` changes
- Fix LCD editing of `junction_deviation_mm`
2018-06-11 22:05:16 -05:00
Scott Lahteine
f2c3b0d476 Use bit flags for homed/known 2018-06-11 22:05:16 -05:00
Scott Lahteine
43bdd0bfe4 Fix indent in stepper.h 2018-06-11 19:17:46 -05:00
Scott Lahteine
3fd1f32b73 Fix ADC key and chamber temp 2018-06-10 20:11:40 -05:00
Scott Lahteine
a2f521d34b
Add Junction Deviation mm runtime setting (#10990) 2018-06-10 18:02:54 -05:00
etagle
6f14bcaa3e Add MAXIMUM_STEPPER_RATE, enforce in multi-stepping
The timing value should be properly set for ALL boards. The compiler will check and set maximum step rate calculations based on those values.
2018-06-10 16:02:47 -05:00
etagle
39a7e7720d Adaptive multiaxis step smoothing
- Stepper bugs fixed
- Support MIXING_EXTRUDER with Linear Advance
- Miscellaneous cleanup
2018-06-10 16:02:47 -05:00
Giuliano
b64cc9329e [2.0.x] Fix dual enstop home (#10980) 2018-06-10 02:08:47 -05:00
Scott Lahteine
3701869e6c Add HAL_timer_start for AVR, use stepper timer to time pulses 2018-06-09 22:30:13 -05:00
etagle
d82704354f Increase the planner first block HOLD delay to 100mS 2018-06-09 21:12:37 -05:00
Scott Lahteine
334341c632
Hephestos config updates (#10960) 2018-06-07 21:23:55 -05:00
Scott Lahteine
55aedf036b Fix M503 ABL mesh report. (Zero-based IJ indices) 2018-06-07 16:36:50 -05:00
Scott Lahteine
d8b983f624
More concise M503 output for M906, M913, M914 (#10947) 2018-06-06 20:58:28 -05:00
Scott Lahteine
ad8d3150aa Cleanup for dual endstops homing 2018-06-03 00:34:29 -05:00
Eduardo José Tagle
d3c02410a8 [2.0.x] Small assorted collection of fixes and improvements (#10911)
* Misc fixes and improvements

- Get rid of most critical sections on the Serial port drivers for AVR and DUE. Proper usage of FIFOs should allow interrupts to stay enabled without harm to queuing and dequeuing.
  Also, with 8-bit indices (for AVR) and up to 32-bit indices (for ARM), there is no need to protect reads and writes to those indices.
- Simplify the XON/XOFF logic quite a bit. Much cleaner now (both for AVR and ARM)
- Prevent a race condition (edge case) that could happen when estimating the proper value for the stepper timer (by reading it) and writing the calculated value for the time to the next ISR by disabling interrupts in those critical and small sections of the code - The problem could lead to lost steps.
- Fix dual endstops not properly homing bug (maybe).

* Set position immediately when possible
2018-06-01 19:02:22 -05:00
Scott Lahteine
2deff0d9b9 Fix/Improve junction deviation
- Respect axis max acceleration limits instead of forcing a fixed acceleration value.
- The `junction_unit_vec` ensures proper handling of entry and exit speeds even when the axes involved have different limits.
2018-05-31 20:09:53 -05:00
Scott Lahteine
d259070980 Clean up trailing spaces from vim, etc. 2018-05-31 00:09:41 -05:00
Scott Lahteine
b90f54b0fc Improve probe logging 2018-05-29 21:54:13 -05:00
Scott Lahteine
4299e5dc8b
Modify E-stepping macros for use in LINEAR_ADVANCE (#10885) 2018-05-28 19:34:08 -05:00
Scott Lahteine
8f14ef855d More concise commentary in planner.cpp 2018-05-28 19:25:18 -05:00
Scott Lahteine
6919e87656 Minor cleanup of multi-stepping logic 2018-05-28 17:44:33 -05:00
Scott Lahteine
853a9056ac Long thermistor tables need special consideration 2018-05-28 06:28:34 -05:00
Scott Lahteine
a4f9c3373f Tweak thermistor spacing 2018-05-28 03:44:32 -05:00
Scott Lahteine
1ce97f1f6d
Faster (bisect) search in thermistor tables (#10883) 2018-05-27 23:27:51 -05:00
Scott Lahteine
0ca9db7051 Correct HOTENDS for SWITCHING_EXTRUDER 2018-05-27 23:22:48 -05:00
Eduardo José Tagle
7b9f0302d4 Fix Bresenham rounding errors, add link to article (#10871) 2018-05-27 01:49:59 -05:00
Scott Lahteine
2566342979 Adjust some commentary 2018-05-27 00:10:25 -05:00
Scott Lahteine
6775a16c97 Fix switching extruder stepping with LA 2018-05-26 19:07:01 -05:00
Scott Lahteine
931ab4ec40 Rename Junction Deviation options 2018-05-26 18:33:51 -05:00
Scott Lahteine
aaaf09bda2 BEZIER_JERK_CONTROL => S_CURVE_ACCELERATION 2018-05-26 18:33:51 -05:00
Scott Lahteine
01d37e00af
Fix up stepper ISR with linear advance timing (#10853)
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
2018-05-26 01:00:13 -05:00
Scott Lahteine
7261f48872 Fix reset of endstops and move state 2018-05-24 19:33:36 -05:00
Scott Lahteine
50fa8e01c1 Minor optimization of axis_did_move bits 2018-05-24 19:08:07 -05:00
Scott Lahteine
f28e366b77 Followup for core endstops 2018-05-24 03:02:57 -05:00
Scott Lahteine
9644d56b42 Patches for core motion tests 2018-05-24 00:49:01 -05:00
Scott Lahteine
3e3789da85
Regression: Endstops Core compatibility (#10823)
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
2018-05-23 03:45:25 -05:00
Scott Lahteine
4b610b333e Tweak G38 formatting 2018-05-22 01:56:03 -05:00
Scott Lahteine
d2647c1f19 Fix G1 behaviour after tool unpark
Fix #10777 for 2.0.x

Co-Authored-By: Ante Vukorepa <o.orcinus@gmail.com>
2018-05-22 00:53:00 -05:00
Scott Lahteine
0c3773d724 Cleanup in stepper_indirection.h 2018-05-22 00:36:03 -05:00
Scott Lahteine
4b2f6e3b2b
[2.0.x] Add endstop noise filter (#10796) 2018-05-21 15:51:38 -05:00
Scott Lahteine
65a004564c Stepper::set_position needed for some applications 2018-05-21 15:21:33 -05:00
Scott Lahteine
435ecb6b67 Followup to stepper/planner refactor 2018-05-20 23:13:38 -05:00
Bob Kuhn
d557c84a71 [2.0.x] Error for FAST_PWM_FAN with 32 bit CPU (#10798) 2018-05-20 11:37:55 -05:00
etagle
569df3fc0c Fix interrupt-based endstop detection
- Also implemented real endstop reading on interrupt.
2018-05-20 07:10:24 -05:00
etagle
a4af975873 Fix planner block optimization
- Fixed the planner incorrectly avoiding optimization of the block following the active one.
- Added extra conditions to terminate planner early and avoid redundant computations.
2018-05-20 07:10:24 -05:00
etagle
e0ca627033 Planner block HOLD flag
Allows the Stepper ISR to wait until a given block is free for use. Allows Planner to plan the first move, which is split into two.
2018-05-20 06:23:58 -05:00
etagle
a11eb50a3e Refactor and optimize Stepper/Planner
Better encapsulation and considerably reduce stepper jitter
2018-05-20 06:23:58 -05:00
etagle
0566badcef Add memory barrier, optimal interrupt on-off
Disabling an ISR on ARM has 3 instructions of latency. A Memory barrier is REQUIRED to ensure proper and predictable disabling. Memory barriers are expensive, so avoid disabling if already disabled (See https://mcuoneclipse.com/2015/10/16/nvic-disabling-interrupts-on-arm-cortex-m-and-the-need-for-a-memory-barrier-instruction/)
2018-05-20 02:39:34 -05:00
Scott Lahteine
7dc03ce721 Simplified fix for babystep pulse width
Alternative to the apparently superfluous double delay
2018-05-19 21:00:08 -05:00
Scott Lahteine
65270d6a96 Fix LIN_ADVANCE + SWITCHING_EXTRUDER
Followup to #10656
2018-05-19 18:32:00 -05:00
Bob Kuhn
9ad42d6617 add delay between pulse edges (#10778) 2018-05-19 17:12:16 -05:00
Scott Lahteine
83d42f33e1 Add HAS_HOTEND_OFFSET_Z conditional 2018-05-19 17:05:15 -05:00
GMagician
3c76bda2d8 Fix switching extruder
`DONT_SWITCH` got lost along the way. Replace it with `DO_SWITCH_EXTRUDER` and adjust the code.
2018-05-19 17:05:15 -05:00
Giuliano
e1d9046efc [2.0.x] Temperature reading fix (#10774) 2018-05-19 15:39:36 -05:00
Scott Lahteine
50270b53a0 Clear up some more compile warnings 2018-05-17 18:40:49 -05:00
Jiri Jaburek
43ddb29f9e Add FAN_MAX_PWM for M106-controlled fans 2018-05-15 21:18:46 -05:00
Scott Lahteine
836b0bbeee Fix MBL line_to_destination
Fix #10708
2018-05-13 16:50:39 -05:00
Scott Lahteine
ba4c32eec5 Followup to _AXIS patch 2018-05-13 10:43:35 -05:00
Scott Lahteine
d9154ebdf6 Followup to math patch 2018-05-13 09:30:27 -05:00
Scott Lahteine
883b0c9880
Convert custom maths to inlines (#10728) 2018-05-13 08:10:08 -05:00
Scott Lahteine
08e36e264e Apply _AXIS macro 2018-05-13 06:51:01 -05:00
Scott Lahteine
99ecdf59af Smarter MIN, MAX, ABS macros
Use macros that explicitly avoid double-evaluation and can be used for any datatype, replacing `min`, `max`, `abs`, `fabs`, `labs`, and `FABS`.

Co-Authored-By: ejtagle <ejtagle@hotmail.com>
2018-05-13 04:52:56 -05:00
Scott Lahteine
083ec9963e Tweaks to heater / lcd conditions 2018-05-13 04:52:56 -05:00
Scott Lahteine
8f8c6a9bc4
Move get_axis_position_mm to Planner (#10718) 2018-05-12 09:59:11 -05:00