Commit graph

1811 commits

Author SHA1 Message Date
Scott Lahteine
a561bd5e3a New feature: SDCARD_SORT_ALPHA 2017-02-14 21:37:24 -06:00
Scott Lahteine
467f01435f Merge pull request #5816 from thinkyhead/rc_abl_virt_reduce
Reduce memory use by ABL_BILINEAR_SUBDIVISION slightly
2017-02-14 08:41:44 -06:00
jes
eaa829b58c Reduce memory use by ABL_BILINEAR_SUBDIVISION slightly 2017-02-12 04:09:48 -06:00
Scott Lahteine
701f4a6d9d Merge pull request #5729 from Bob-the-Kuhn/guaranteed-BLTouch-detection
guaranteed BLTouch detection
2017-02-12 01:13:35 -06:00
Scott Lahteine
1bc5be3bdf Cast DELTA_PRINTABLE_RADIUS to float in sq()
Addressing #5625
2017-02-11 23:28:39 -06:00
Bob-the-Kuhn
0369f97ec1 guaranteed BLTouch detection
To guarantee that the 5mS pulse from a BLTouch is recognized you need to
have the endstops.update() routine run twice in that 5mS period.

At 200 steps per mm, my system has problems  below a feedrate of 120 mm
per minute.

Two things were done to guarantee the two updates within 5mS:
1) In interrupt mode, a check was added to the temperature ISR.  If the
endstop interrupt flag/counter is active then it'll kick off the endstop
update routine every 1mS until the flag/counter is zero.  This
flag/counter is decremented by the temperature ISR AND by the stepper
ISR.

2) In poling mode, code was added to the stepper ISR that will make sure
the ISR runs about every 1.5mS.  The "extra" ISR runs only check the
endstops.  This was done by grabbing the intended ISR delay and, if it's
over 2.0mS, splitting the intended delay into multiple smaller delays.
The first delay can be up to 2.0mS, the next ones 1.5mS (as needed) and
the last no less than 0.5mS.

=========================================

BLTouch error state recovery

If BLTouch already active when deploying the probe then try to reset it
& clear the probe.

If that doesn't fix it then declare an error.

Also added BLTouch init routine to startup section
2017-02-11 12:01:34 -06:00
Florian Heilmann
7bbc31704c Adjust probe_pt() terminal output to respect probe z-offset 2017-02-09 22:54:22 -06:00
Scott Lahteine
9b5515926a Merge pull request #5696 from thinkyhead/rc_volumetric_default
Allow enabling volumetric filament on config load
2017-01-14 05:48:51 -08:00
Robert Kirk
0d147ead66 Allow enabling volumetric filament on config load 2017-01-14 04:37:49 -08:00
AnHardt
fa26767efe Replace all remaining 'boolean' with 'bool' 2017-01-13 13:03:52 +01:00
AnHardt
f6858d9974 Fix M110 without leading N
Store N in the right variable.
This is too rarely used.

"mea culpa, mea culpa, mea maxima culpa"
2017-01-13 12:33:50 +01:00
Scott Lahteine
c376f6a2cb code_value_float tweak 2017-01-12 04:38:09 -08:00
Robert Kirk
306c184b1a Allow M600 when dryrun debugging 2016-12-21 20:30:51 -05:00
Damien
4e2639942b Support for M335 case light "no case light" 2016-12-19 23:23:08 -08:00
Robert Kirk
f724ef5820 Have bed leveling status output current status, not requested. 2016-12-19 18:47:45 -08:00
Scott Lahteine
f9f75c8016 Fix USE_RAW_KINEMATICS in prepare_kinematic_move_to 2016-12-15 23:15:38 -08:00
Scott Lahteine
78d6d6e076 Merge pull request #5452 from thinkyhead/rc_save_your_mesh
Save Bed Leveling to EEPROM
2016-12-15 20:23:01 -08:00
Scott Lahteine
d4f5418802 Merge pull request #5517 from esenapaj/Fix-for-PR-#5255
Fix for the PR #5255 (Case light menu (3rd attempt))
2016-12-15 20:01:22 -08:00
Scott Lahteine
6d7b1cdf6c Add M421 for ABL Bilinear 2016-12-15 19:39:11 -08:00
Scott Lahteine
32e65dc429 Extend M420 to print state and, with V, the matrix / mesh 2016-12-15 19:39:11 -08:00
Scott Lahteine
d04258753b Don't throw away the bed level matrix on G28 2016-12-15 19:21:18 -08:00
Scott Lahteine
8f0f225d10 Save ABL Planar Matrix to EEPROM 2016-12-15 19:21:15 -08:00
Scott Lahteine
e42fd7813a Save ABL Bilinear Grid to EEPROM 2016-12-15 19:20:48 -08:00
Scott Lahteine
55722c09da Use "UNPROBED" for un-probed bed_level_grid points 2016-12-15 19:08:44 -08:00
Scott Lahteine
2643404ac8 Throw an error in M420 if can't enable 2016-12-15 19:08:43 -08:00
Scott Lahteine
b1539394fd Use planner.unapply_leveling to undo tilt in G29 2016-12-15 19:08:43 -08:00
Scott Lahteine
04636f78eb Re-enable MBL/ABL after M48 2016-12-15 19:08:43 -08:00
Scott Lahteine
9b41638672 Minor tweak to G29 grid points 2016-12-15 19:08:42 -08:00
Scott Lahteine
daa2cad21f Fix comment on G29 to include 'Z' 2016-12-15 19:08:42 -08:00
Scott Lahteine
8244fefcc2 Tweak call to reset_bed_level in G29 2016-12-15 19:08:42 -08:00
Scott Lahteine
0995a5d734 Fixup reset_bed_level 2016-12-15 19:08:42 -08:00
Scott Lahteine
1b2fb2bdc7 ABL_GRID_POINTS_* => ABL_GRID_MAX_POINTS_* 2016-12-15 19:08:41 -08:00
esenapaj
88157ba529 Fix for the PR #5255 (Case light menu (3rd attempt)) 2016-12-16 00:57:32 +09:00
esenapaj
069c6b38dd Remove unnecessary tabs and spaces 2016-12-16 00:21:32 +09:00
Scott Lahteine
8d9fcd8e6f Merge pull request #5495 from AnHardt/autoadjusting_display-updates
Adaptive screen updates for all kinds of displays
2016-12-14 04:16:26 -08:00
AnHardt
d0e24e0876 Adaptive screen updates for all kinds of displays
The target here is to update the screens of graphical and char base
displays as fast as possible, without draining the planner buffer too much.

For that measure the time it takes to draw and transfer one
(partial) screen to the display. Build a max. value from that.
Because ther can be large differences, depending on how much the display
updates are interrupted, the max value is decreased by one ms/s. This way
it can shrink again.
On the other side we keep track on how much time it takes to empty the
planner buffer.
Now we draw the next (partial) display update only then, when we do not
drain the planner buffer to much. We draw only when the time in the
buffer is two times larger than a update takes, or the buffer is empty anyway.

When we have begun to draw a screen we do not wait until the next 100ms
time slot comes. We draw the next partial screen as fast as possible, but
give the system a chance to refill the buffers a bit.

When we see, during drawing a screen, the screen contend has changed,
we stop the current draw and begin to draw the new content from the top.
2016-12-13 18:44:34 +01:00
Scott Lahteine
94ffb58da7 Prevent retract un-hop at wrong height 2016-12-13 08:24:12 -08:00
Scott Lahteine
4bc6536f54 Move to safe zone on DELTA if using do_blocking_move_to* 2016-12-10 21:28:24 -08:00
esenapaj
e9393c3634 Suppress warnings, etc
・Suppress warnings
・Remove unused variable "did_update"
2016-12-08 17:47:59 +09:00
Scott Lahteine
83c5026db1 Ignore homing button when SD printing
As suggested in #5404 by @android444
2016-12-06 14:22:34 -06:00
akaJes
d7b948610a Experimental bilinear subdivision option 2016-12-05 20:11:24 -06:00
Scott Lahteine
b203901143 Merge pull request #5393 from AnHardt/Fix-auto_report_temperatures
Fix auto_report_temperatures()
2016-12-05 19:38:23 -06:00
AnHardt
59a27ed27d Fix auto_report_temperatures()
The `auto_report_temperatures` needs a linefeed to be recognized by Repetier Host.
2016-12-06 01:26:44 +01:00
Scott Lahteine
b6b100c471 Merge pull request #5371 from thinkyhead/rc_extruders_can_differ
Allow distinct factors for multiple extruders
2016-12-05 11:22:31 -06:00
Scott Lahteine
3391c785c6 Support for distinct E factors 2016-12-05 07:26:18 -06:00
Scott Lahteine
c47e07d129 Fix Dual X software endstops 2016-12-05 06:51:41 -06:00
Scott Lahteine
4217e9653e Adjust park code in tool_change 2016-12-05 06:51:41 -06:00
Scott Lahteine
b20405db31 Only DXC_AUTO_PARK_MODE should auto-move in tool_change 2016-12-05 06:48:43 -06:00
Scott Lahteine
ca24af7d5d Dual X with home_z_safely is not parked 2016-12-05 06:43:26 -06:00
Scott Lahteine
0e15b4f434 Dual X set_axis_is_at_home can use x_home_pos for both 2016-12-05 06:43:26 -06:00
Scott Lahteine
54109dfaec Reduce code size for Dual X un-park 2016-12-05 06:43:26 -06:00
Scott Lahteine
fe96f74db1 Use const arguments in Dual X helper functions 2016-12-05 06:43:26 -06:00
Scott Lahteine
41278c1e8b Apply LOGICAL_POSITION to home positions on Dual X 2016-12-05 06:43:26 -06:00
Scott Lahteine
053fb55af6 Fix modes ordering in prepare_move_to_destination_dualx 2016-12-05 06:43:26 -06:00
Scott Lahteine
56dd15c0ad Use SET_INPUT for PS_ON_PIN in kill 2016-12-05 06:43:26 -06:00
Scott Lahteine
c06161b773 Use apply_leveling, not MBL directly 2016-12-05 01:53:36 -06:00
Scott Lahteine
fccc97de6d Save PROGMEM with string changes
Unlike RAM-based strings, PROGMEM strings aren’t consolidated by the
compiler.
2016-12-03 19:21:46 -06:00
Scott Lahteine
27dd5acc22 Fix set_led_color for BLINKM
Follow-up to #5330
2016-12-03 01:51:11 -06:00
Scott Lahteine
f60b4f8659 Allow case light pin to be active low 2016-12-01 23:32:34 -06:00
Scott Lahteine
65c50e062e Support for an RGB LED using 3 pins 2016-11-30 00:02:31 -06:00
Scott Lahteine
092e949b58 Merge pull request #5169 from thinkyhead/rc_core_inverted
Support for COREYX, COREZX, COREZY
2016-11-28 02:26:41 -06:00
Scott Lahteine
c7935bb0d2 Merge pull request #5299 from thinkyhead/rc_bed_correction_fade
Add a fade factor for mesh leveling
2016-11-28 02:07:51 -06:00
Scott Lahteine
61437d988a Fix and optimize case-light code 2016-11-28 01:34:52 -06:00
Scott Lahteine
f6f77d34a1 Add a fade factor for mesh leveling 2016-11-26 03:41:26 -06:00
Scott Lahteine
2e966f8e5b Patch Capabilities Report for "PROGRESS" 2016-11-23 19:31:46 -06:00
Scott Lahteine
d891324830 Merge pull request #5258 from mosh1/mbl_speed_fix
Fix z feedrate value when doing mesh bed leveling. probe feedrate use…
2016-11-23 14:15:01 -06:00
Scott Lahteine
7f8133a51f Merge pull request #5255 from Kaibob2/CaseLightMenu
Case light menu (3rd attempt)
2016-11-23 13:46:33 -06:00
Kai
0c341f0c50 Added Menu entry for Case light 2016-11-23 19:29:15 +01:00
Scott Lahteine
3bc2273ac9 Comment M540 2016-11-21 18:08:00 -06:00
Scott Lahteine
14b74181f5 Merge pull request #5179 from thinkyhead/rc_TMC2130
TMC2130 "Silent StepStick" support
2016-11-21 14:10:52 -06:00
Scott Lahteine
bb2114a060 Merge pull request #5264 from thinkyhead/rc_delta_safe_zone
Add an option for delta to home to the top
2016-11-21 13:56:44 -06:00
Scott Lahteine
9b96a4a53b Merge pull request #5246 from thinkyhead/rc_some_cleanup
Minor stepper cleanup
2016-11-21 13:55:25 -06:00
Scott Lahteine
3e0376b45e Reorder M114 and M119 gcode cases 2016-11-21 00:52:19 -06:00
Scott Lahteine
127e21ae00 Extend M122 for all steppers 2016-11-21 00:52:18 -06:00
Moritz
d67c1d825f Add TMC2130 support 2016-11-21 00:17:45 -06:00
Scott Lahteine
11effeee2c Add an option for delta to home to the top 2016-11-20 23:12:07 -06:00
Moshen Chan
29b174bfb9 Fix z feedrate value when doing mesh bed leveling. probe feedrate uses XY_PROBE_SPEED 2016-11-19 16:34:41 -08:00
Scott Lahteine
87b6b19256 Patch CASE_LIGHT typo 2016-11-18 23:49:12 -06:00
Scott Lahteine
181cdb3cfe Move GCode list above include lines 2016-11-18 22:24:46 -06:00
Scott Lahteine
eb120e518c Followup to new endstop interrupts feature
- Fix typos, verbiage
- Fix naming of `setup_endstop_interrupts`
- Some formatting, indentation, spacing
2016-11-18 21:53:45 -06:00
Scott Lahteine
832fe284b4 Merge pull request #5184 from AnHardt/endstop_interrupts
Introduce endstop interrupts
2016-11-18 20:50:24 -06:00
Scott Lahteine
98600e1433 Minor stepper cleanup 2016-11-18 01:15:57 -06:00
Florian Heilmann
d08867986e Add autotemp capabilities to M104
This allows M104 to pass the F and B parameters to enable autotemp as well
2016-11-17 11:28:19 -06:00
Scott Lahteine
2330619da0 Merge pull request #5191 from petrzjunior/const
Replace const bool with #define for consistency
2016-11-17 03:37:32 -06:00
Petr Zahradník junior
d7ce5d271b
Replace const bool with #define for consistency 2016-11-16 18:55:21 +01:00
Scott Lahteine
5d23e52d75 Merge pull request #5228 from thinkyhead/rc_keep_last_mix
Fix DIRECT_MIXING_IN_G1 to preserve the previous mix
2016-11-15 19:12:01 -06:00
Scott Lahteine
99b0c1fe56 Fix DIRECT_MIXING_IN_G1 to preserve the previous mix 2016-11-15 16:12:26 -06:00
Scott Lahteine
410657b050 Fix G30 with limits, print correct probe XY 2016-11-15 14:10:28 -06:00
AnHardt
f3eee02596 Introduce endstop interrupts
If ENDSTOP_INTERRUPTS_FEATURE is enabled this tries to set up interrupt routines
for all used endstop pins. If this worked without errors, `endstops.update()` is called
only if one of the endstops changed its state.

The new interrupt routines do not really check the endstops and react upon them. All what they
do, is to set a flag if it makes sense to call the endstop test we are used to.

This can be used on:
* ARM (DUE) based boards - all pins can raise interrupts,
* RAMPS - all 6 endstop pins plus some other on EXT-2 can raise interrupts,
* RAMPS based boards - as long the designers did not change the pins for the endstops or at least left enough,
* all boards, if there are enough pins that can raise interrupts, and you are willing/able to swap with pins dedicated to other purpose.
2016-11-15 12:07:41 +01:00
Scott Lahteine
665b7f3893 Merge pull request #5212 from thinkyhead/rc_mixing_faster
Store mix factors as reciprocals and multiply
2016-11-12 18:47:11 -06:00
Scott Lahteine
60cc9342a4 Merge pull request #5188 from thinkyhead/rc_extended_host_support
Extended host support: M155 Auto temp report, M115 capabilities
2016-11-12 15:38:06 -06:00
Scott Lahteine
f663220e87 Store Mix factors as reciprocals and multiply 2016-11-12 15:19:18 -06:00
Scott Lahteine
b31a07e261 Stateful M355 with separate P parameter 2016-11-09 03:28:18 -06:00
Scott Lahteine
3c9a838651 Extended capabilities report in M115 2016-11-09 02:32:58 -06:00
Scott Lahteine
68b866b5dd Add M155 - Auto-report temperature with interval 2016-11-09 02:32:58 -06:00
Scott Lahteine
75bfde9945 M155=>M260, M156=>M261 2016-11-08 17:54:54 -06:00
Scott Lahteine
dcfd7c69e8 Merge pull request #5163 from nzinov/RCBugFix
Improve G30 probing command - add optional arguments
2016-11-07 11:37:13 -06:00
Scott Lahteine
e765eebfb0 Patch spacing in bilinear grid report 2016-11-07 04:08:25 -06:00
Scott Lahteine
1864b282c5 Implement reversed CORE options 2016-11-05 23:47:51 -05:00
Nikolay Zinov
dea00bbcf1 improve G30 probing
Add optional parameters
X, Y for probe point
S sets stowing on and off
2016-11-05 13:22:45 +03:00
Scott Lahteine
176aeafc19 Don't define bilinear_line_to_destination on kinematic setups 2016-11-03 14:10:07 -05:00
Scott Lahteine
236853df22 Corrections to bilinear_line_to_destination
- Allow more than 9x9 probe points
- Account for the probe starting position
2016-11-03 04:43:59 -05:00
Scott Lahteine
0115e495fe Fix up Dual X switch blocks 2016-11-02 21:38:50 -05:00
Scott Lahteine
2495ab7af2 Make dual_x_carriage_mode an enumeration 2016-11-02 21:38:49 -05:00
Scott Lahteine
d6c36f5bb9 Fix Z raise with DXC_AUTO_PARK_MODE 2016-11-02 21:36:50 -05:00
Scott Lahteine
0c79553fc5 Cast int to AxisEnum for some accessors 2016-11-02 17:42:24 -05:00
Scott Lahteine
adbf1f7dca Add M355 to the GCodes list. 2016-11-02 16:43:52 -05:00
Scott Lahteine
63efc10599 Merge pull request #5134 from thinkyhead/rc_bilinear_split_lines
Split cartesian moves on grid boundaries with bilinear ABL
2016-11-02 16:14:55 -05:00
Scott Lahteine
ee5b8d6dc8 Split moves on grid boundaries with bilinear ABL on cartesian 2016-11-01 08:25:47 -05:00
Scott Lahteine
66744a6076 Merge pull request #5133 from thinkyhead/rc_M355_case_light
M355 Case light
2016-11-01 07:51:27 -05:00
Scott Lahteine
955d14acb0 Patch photo pin code style 2016-11-01 06:30:14 -05:00
Stanley
ab3f966f5f Case light G-code M355
implemented G-Code M355 into Marlin
2016-11-01 06:30:14 -05:00
Sebastianv650
f9bea7968f BugFix for incorrect E-speed calculation
The extrusion speed was wrong due to a not high enough precision of
esteps to XY steps, therefore now the target float values are used to
calculate the ratio between XY movement and extrusion speed.
The e_speed_multiplier8 was replaced by an absolute multiplier called
abs_adv_steps_multiplier8, therefore one multiplication and bitshift can
be saved inside the stepper ISR. Due to this, also extruder_advance_k is
better suited inside the planner and not the stepper files any more.
2016-11-01 08:08:47 +01:00
Scott Lahteine
ff3a8ca0d1 Use NUM_DIGITAL_PINS instead of custom DIO_COUNT 2016-10-31 08:08:03 -05:00
Scott Lahteine
04a1fac029 Some cleanup to M43 2016-10-31 08:08:03 -05:00
Bob-the-Kuhn
c7f1f0dae6 Add endstop monitor & make pins report pretty 2016-10-31 08:08:02 -05:00
Scott Lahteine
396434a445 Fix compiler warning in M145 2016-10-28 20:57:36 -05:00
Scott Lahteine
07bfc45df8 Adjust spacing in gcode_M149 2016-10-28 20:57:36 -05:00
Scott Lahteine
1a2310c494 Make LCD preheat vars an array to reduce code size 2016-10-28 20:57:36 -05:00
Scott Lahteine
50ee749082 Centralize click-handling in the LCD loop 2016-10-28 20:57:21 -05:00
Scott Lahteine
47ad97c35e Merge pull request #5109 from thinkyhead/rc_eeprom_M218_tool_offset
Save hotend_offset array (M218) in EEPROM
2016-10-28 20:08:29 -05:00
Scott Lahteine
67ab54185b Save hotend_offset array (M218) in EEPROM 2016-10-28 18:45:23 -05:00
MagoKimbra
dfcdbb437b Fix Command M420 2016-10-28 20:53:48 +02:00
Scott Lahteine
c34dbfb248 Merge pull request #5072 from thinkyhead/rc_preset_auto_fans
Add predefined AUTO_FAN_PINs to pins files
2016-10-27 17:12:11 -05:00
Scott Lahteine
c4c53856a4 Merge pull request #5094 from esenapaj/Fix-for-the-PR-#5088
Fix for the PR #5088 (Handle M108 in M1 also with ULTIPANEL)
2016-10-26 21:51:18 -05:00
esenapaj
d5a5042d23 Fix for the PR #5088 (Handle M108 in M1 also with ULTIPANEL) 2016-10-27 10:32:20 +09:00
Scott Lahteine
3f94b15cef Fix bilinear grid constraints
Followup to #5090
2016-10-26 18:11:26 -05:00
Scott Lahteine
ada935de87 Allow TEMP_STAT_LEDS with only one LED defined 2016-10-26 17:51:26 -05:00
Scott Lahteine
f0d673561f Fix for bilinear grid outside bounds 2016-10-26 05:00:03 -05:00
Scott Lahteine
1ba1ec0db9 Handle M108 in M1 also with ULTIPANEL 2016-10-25 23:25:47 -05:00
Greg Cormier
f0aed9dac7 Fix #4995 - M48/G29 on CoreXY maybe others? 2016-10-22 20:45:13 -04:00
Scott Lahteine
3544c3632f Merge pull request #5062 from thinkyhead/rc_warnings_fix
Warnings fixed redux
2016-10-22 12:21:36 -05:00
Josef Pavlik
0bd66807b2 fixed warning: extra ; 2016-10-22 11:12:29 -05:00
Scott Lahteine
5f5a55a0de Add a ZERO macro to clear arrays 2016-10-22 10:07:18 -05:00
Scott Lahteine
2783dcb4cc Save some RAM in MBL's G29 2016-10-22 02:52:56 -05:00
esenapaj
385bd8a4a3 Fix freezing and MINTEMP Error with MAX31855 thermocouple 2016-10-16 07:33:14 +09:00
Scott Lahteine
ca7275a67a Disable EXTRAPOLATE_FROM_EDGE by default 2016-10-14 14:44:28 -05:00
Scott Lahteine
e7cf566fc5 Do kinematic segments with buffer_line_kinematic
This breaks the raw option, but in the future perhaps all planner moves
will be sent in raw form instead of logical.
2016-10-10 17:14:03 -05:00
Scott Lahteine
a10e81dc2a Minor cleanup of set_bed_leveling_enabled 2016-10-10 17:14:03 -05:00
Scott Lahteine
029824bc49 Patch ADJUST_DELTA macro for SCARA 2016-10-10 17:14:03 -05:00
Scott Lahteine
d963020532 Sort out some header dependencies 2016-10-10 17:14:03 -05:00
Scott Lahteine
a07033a6c1 Merge pull request #4974 from esenapaj/Follow-up-the-PR-#4955
Fix and follow-up the PR #4955 (PINS_DEBUGGING and M43: Read pin states), etc
2016-10-10 13:27:52 -05:00
Scott Lahteine
f8199b2cc1 Merge pull request #4982 from thinkyhead/rc_abl_bugfix
Fix planner with kinematics, delta ABL
2016-10-10 13:24:22 -05:00
esenapaj
00456b0cb3 Fix compilation errors 2016-10-10 14:22:43 +09:00
Scott Lahteine
e4e290d957 Make EXTRUDER_RUNOUT_PREVENT kinematic compatible 2016-10-09 15:58:33 -05:00
Scott Lahteine
847429eff4 Make tool_change kinematic compatible 2016-10-09 15:58:32 -05:00
Scott Lahteine
a4a7ca10ca Make USE_DELTA_IK_INTERPOLATION compatible with ABL 2016-10-09 15:58:32 -05:00
Scott Lahteine
c5cac486f5 Use a, b, c instead of lx, ly, lz 2016-10-09 14:34:24 -05:00
Josef Pavlik
f8c2473a71 Improve planner kinematics, fix delta ABL 2016-10-09 13:32:46 -05:00
Scott Lahteine
e4d2662d81 Use some macros in M48 2016-10-09 12:21:05 -05:00