Commit graph

8722 commits

Author SHA1 Message Date
Scott Lahteine 5ac226aa93 Further cleanup of inline delays 2018-04-27 19:22:22 -05:00
Marcio Teixeira 724e9f56c8 Removed "const" to match parser. (#10548) 2018-04-27 17:48:52 -05:00
Giuliano 2e1939e85c [2.0.x] report error on unsupported commands (#10553)
Raise an error when an unknown/unsupported G/M command is requires.

This will address #10546
2018-04-27 17:40:27 -05:00
Scott Lahteine a474a7e675 Correct AVR_ATmega328_FAMILY macro
…as with #10540

Co-Authored-By: per1234 <per1234@users.noreply.github.com>
2018-04-27 03:13:46 -05:00
Scott Lahteine f790b4bc0a Reorganize some conditionals 2018-04-27 02:23:11 -05:00
Scott Lahteine a51ba6e3f6 Fix ABL grid bounds test for Delta/SCARA
Addressing #10538
2018-04-27 02:23:10 -05:00
Scott Lahteine df6bc812b5 Fix disable of Z_HOMING_SENSITIVITY for HOMING_Z_WITH_PROBE
As pointed out in #10532
2018-04-27 02:23:10 -05:00
Scott Lahteine 63e0b36f8b Fix G29_RECOVER_COMMANDS typo 2018-04-27 02:23:10 -05:00
Scott Lahteine f83361a814 Apply const to tmc_sensorless_homing 2018-04-27 02:23:10 -05:00
Scott Lahteine 212e52e485 Basic delay for Max7219 on ARM 2018-04-27 00:41:29 -05:00
Scott Lahteine 7b6e742436 Wrap delay macros in do{}while(0) 2018-04-26 18:18:23 -05:00
Karl Andersson 58ca3be1ec delayMicroseconds() cannot be called in critical section (#10535)
on the STM32 platform
2018-04-26 14:31:01 -05:00
Bob-the-Kuhn 00dfaae8df [2.0.x] Platformio - automate build & environment selection (#10503) 2018-04-26 02:42:06 -05:00
Scott Lahteine 299c4fed42 Undefine PIDTEMPBED without a bed heater 2018-04-26 01:30:10 -05:00
Scott Lahteine 456cf971af HAL FastIO cleanup and fixes 2018-04-26 00:40:16 -05:00
J.C. Nelson 5b5e322356 Set Interrupt Priorities and Grouping for STM32F103. (#10517) 2018-04-26 00:21:16 -05:00
Scott Lahteine 0e450df6a2 MKS OLED support for RUMBA
Based on #10519

Co-Authored-By: Alex <alex18881@users.noreply.github.com>
2018-04-25 23:00:44 -05:00
Scott Lahteine 2578996631
[2.0.x] Emergency parser for multiple serial ports (#10524) 2018-04-25 20:58:00 -05:00
Scott Lahteine 8cc31d1b2e Cleanup to emergency parser
Followup to #10516
2018-04-25 06:54:37 -05:00
Chris Pepper 2242b98248 [LPC176x] Emergency Parser Feature (#10516) 2018-04-25 06:44:26 -05:00
Scott Lahteine eef0248a1c
Add M420 C to adjust the whole mesh (#10522) 2018-04-25 06:43:45 -05:00
Eduardo José Tagle c1e5ebbc1e [2.0.x] AVR: Atomic bit set and clear of upper pin ports without critical section (#10502)
* AVR: Atomic bit set and clear

The critical section can be dropped, saving 3 cycles per access. Also simplified pin toggling for all ports.
2018-04-24 13:45:43 -05:00
Marcio Teixeira 02a711c4d6 [2.0.x] Fix crash upon repeated calls to process_subcommands_now_P (#10509) 2018-04-24 13:44:22 -05:00
Scott Lahteine a3ce8a3fcd Add sanity checks for EMERGENCY_PARSER 2018-04-24 09:24:26 -05:00
Scott Lahteine f06c3c38b9 Fix M0_M1 with no LCD 2018-04-24 09:22:05 -05:00
Scott Lahteine c82dd5129f Revert potentially-not-redundant UBL test
Response to #10435
2018-04-24 08:04:13 -05:00
Scott Lahteine 9789c1c719 Fix current_temperature_chamber compile error
Fix #10505
2018-04-24 07:55:58 -05:00
Eduardo José Tagle 0c428a66d9 Proper AVR preemptive interrupt handling (#10496)
Also simplify logic on all ARM-based interrupts. Now, it is REQUIRED to properly configure interrupt priority. USART should have highest priority, followed by Stepper, and then all others.
2018-04-23 22:05:07 -05:00
Scott Lahteine f423e54f77 Strip trailing spaces 2018-04-23 18:00:43 -05:00
Scott Lahteine 8177c4334e
Merge pull request #10498 from xC0000005/MalyanLCDFix
Fix overridden Malyan LCD functions
2018-04-23 17:22:43 -05:00
Scott Lahteine cb46cb8480
Add HAS_HEATED_BED conditional (#10495) 2018-04-23 17:13:01 -05:00
Marcio Teixeira 10a25f733e Add SENSORLESS_HOMING to Archim 2.0 (#10500) 2018-04-23 17:11:33 -05:00
xC0000005 24d23ce49b Fix function definitions for Malyan LCD 2018-04-23 16:56:37 -05:00
Alexey Shvetsov ad58b626a3 Fix pin mappings for Viki2 on Azteeg X5 GT (#10487) 2018-04-22 18:41:30 -05:00
Scott Lahteine 9e07df5c1b
Extra options for LEVEL_BED_CORNERS (#10483) 2018-04-22 02:50:48 -05:00
Scott Lahteine 1c3d49afe0 Fix G28 with Z_AFTER_PROBING
Fix #10476
2018-04-22 01:23:26 -05:00
Scott Lahteine b6747c742a Cleanup AZTEEG_X5_GT pins for VIKI
What should the SD detect and SDSS pins be? Followup soon on #8138
2018-04-22 01:19:43 -05:00
Scott Lahteine 023385ca59
Merge pull request #10479 from thinkyhead/bf2_creality_power_loss_resume
[2.0.x] Creality3D Power-Loss Recovery
2018-04-22 00:17:44 -05:00
Scott Lahteine 3396671011
[2.0.x] Reset LCD status to fallbacks (#10470)
* Remove obsolete strings
* Tweak some static consts
* Reset LCD status to fallbacks
2018-04-22 00:16:30 -05:00
Scott Lahteine d58450c82a Russian language update
Co-Authored-By: anton-piliugin <34044202+anton-piliugin@users.noreply.github.com>
2018-04-22 00:14:20 -05:00
Scott Lahteine 11ab017dd0 Creality3D Power-Loss Recovery 2018-04-21 21:56:50 -05:00
Scott Lahteine 594d6f9efd Add POWER_LOSS_RECOVERY to example configs 2018-04-21 19:40:46 -05:00
Scott Lahteine 7dcd0a1cff Add R parameter to G28 to specify pre-raise 2018-04-21 19:07:48 -05:00
Scott Lahteine 2f4b4d6076 Add Stopwatch::resume method 2018-04-21 19:06:05 -05:00
Scott Lahteine a90cbc6339
[2.0.x] Wait for bed heaters between probing (#10472) 2018-04-21 15:43:21 -05:00
Scott Lahteine a0dac95d25
Merge pull request #10460 from thinkyhead/bf2_trigorilla_14
[2.0.x] Split TRIGORILLA into 1.3 and 1.4
2018-04-20 18:25:40 -05:00
Scott Lahteine f0cbf3d432 Correction to sanity check 2018-04-20 18:16:27 -05:00
Scott Lahteine d8a8eec6ea Add THERMAL_PROTECTION capability
Based on #10465

In response to `M115` the firmware reports if Thermal Protection is enabled (1) or not (0). This information can be used by software such as OctoPrint (more precisely the Printer Safety Check plugin) to warn users when Thermal Protection is not enabled in the firmware.

Co-Authored-By: andrivet <sebastien@advtools.com>
2018-04-20 16:50:50 -05:00
Scott Lahteine 186d71b361 Complete CREALITY_ENDER revert 2018-04-20 16:17:25 -05:00
Scott Lahteine 11ef432476 Match Makefile to boards.h 2018-04-20 16:13:50 -05:00
Scott Lahteine 2be5fe5ddf Split TRIGORILLA into 1.3 and 1.4 2018-04-20 16:12:25 -05:00
Scott Lahteine 80e29492c6 TRIGORILLA => TRIGORILLA_13 2018-04-20 16:12:25 -05:00
Scott Lahteine dea686cf55
Define short pin names in fastio for STM32 (#10461) 2018-04-20 14:54:35 -05:00
Scott Lahteine 65a6a86d19 Don't report point 0 in MBL G29 2018-04-20 13:12:50 -05:00
Scott Lahteine 6faa93d787 Add G29_RETRY_AND_RECOVER to example configs 2018-04-19 19:45:53 -05:00
Marcio Teixeira 5cc7916e69 Add G29_RETRY_AND_RECOVER feature
- Add an option to retry G29, optionally executing a G-code procedure after each failed probe.
2018-04-19 19:45:53 -05:00
Scott Lahteine 78ea4871f9 Fix up enqueue now functions
…and apply to MALYAN_LCD.
2018-04-19 19:45:53 -05:00
Roxy-3D 23635c2b64
Update ubl_motion.cpp
Restore necessary and needed loop termination logic.
2018-04-19 12:04:35 -05:00
Scott Lahteine 8ca3c43d73 Updated language_data spacing, headers 2018-04-19 06:16:16 -05:00
Scott Lahteine 184c077c58 Correct includes (u8g.h) and spelling 2018-04-19 06:16:16 -05:00
Yunhui Fu 627348b46c move the TALL_FONT_CORRECTION to language files 2018-04-19 06:16:16 -05:00
Yunhui Fu 77bc653524 Use X windows 6x12 bitmap font to support western languages. 2018-04-19 06:16:15 -05:00
Yunhui Fu d81649b365 Update language data for sk. 2018-04-19 06:15:19 -05:00
Yunhui Fu 41839746a2 Removed unused macros 2018-04-19 06:15:19 -05:00
Scott Lahteine 4f184ba5da
[2.0.x] Add BOARD_MKS_BASE_15 with digital micro-stepping (#10454)
* Add BOARD_MKS_BASE_15 with digital micro-stepping
* Rename MKS_13 to MKS_GEN_13
2018-04-18 22:58:43 -05:00
Scott Lahteine ad6baa5c9d Fix for UBL set_bed_leveling_enabled 2018-04-18 00:14:48 -05:00
Scott Lahteine df2f24617b Use 0 as the bed position (not Z_MIN_POS) 2018-04-17 20:32:56 -05:00
Karl Andersson 428c54f2ad [2.0.x] HAL for STM32F4 (#10434) 2018-04-17 17:33:29 -05:00
Chris Pepper 744bcaee61 [2.0.x] Fix problems compiling with Arduino IDE (#10441)
* Fix problems compiling u8glib utf8 support on Arduino
* Change header in auto-generated font data
* Change include in font gen scripts
2018-04-17 17:28:55 -05:00
GMagician 20772492aa Fix compile warnings in AVR fastio.h (#10440) 2018-04-17 17:26:57 -05:00
Scott Lahteine f57a008c58
Merge pull request #10443 from thinkyhead/bf2_fix_and_improve
[2.0.x] Improve UBL mesh report, M420 V T, M421 N, and…
2018-04-17 16:59:31 -05:00
Scott Lahteine 89b1580587 Fix compile error in tmc_status 2018-04-17 16:13:28 -05:00
Scott Lahteine 52c024e260 M221 with no parameters report flow 2018-04-17 16:06:25 -05:00
Scott Lahteine 01b01f6dfd Tweak fwretract.retract debug, comments 2018-04-17 16:05:25 -05:00
Scott Lahteine e4acd2c40e One fewer compare in _lcd_move_xyz 2018-04-17 16:03:15 -05:00
Scott Lahteine e05c825a05 Update position for UBL non-segmented activate/deactivate 2018-04-17 16:02:02 -05:00
Scott Lahteine d462be6de6 Try FIXFLOAT rounding based on sign 2018-04-17 15:59:04 -05:00
Scott Lahteine 39c6f65ce7 Ignore LCD_BED_LEVELING with UBL 2018-04-17 15:57:44 -05:00
Scott Lahteine 0746aff595 Improve UBL mesh report. Add M420 T, M421 N 2018-04-17 15:52:56 -05:00
Scott Lahteine 3c826e5d05 Prevent delay when power is already on
Fix #10410
2018-04-17 04:34:31 -05:00
Scott Lahteine 5a064d0e94 Fix bug in planner.set_position_mm 2018-04-16 04:19:58 -05:00
Scott Lahteine 0945674ba2
Use H0 by default with UBL_MESH_EDIT_MOVES_Z (#10428) 2018-04-15 20:49:14 -05:00
Scott Lahteine 6cb83758d7 Fix Brazilian Portuguese language duplicates 2018-04-15 19:18:08 -05:00
Scott Lahteine 8f57e098de Use end-of-line comments in planner.cpp 2018-04-15 19:02:30 -05:00
Scott Lahteine 6c7a17dba6
Abort SD printing more safely (#10407)
Allow the current command to complete when aborting an SD print, otherwise some commands (G28, G29, etc.) will cause trouble.
2018-04-15 18:27:54 -05:00
Chris Pepper c9aed73987 Fix missed includes from HAL macro patch (#10416) 2018-04-15 18:27:34 -05:00
Scott Lahteine 9f8a96fb8a
Brazilian Portuguese update (#10409) 2018-04-15 13:13:46 -05:00
Yunhui Fu 93273a4c9e Fix u8g.h search path error (#10419)
Support env MARLIN_LANGS for user select generated language, and update doc; update script to generate dogm_font_data_ISO10646_1.h automatically.
2018-04-15 13:12:02 -05:00
Scott Lahteine 584735c994 u8g.h => clib/u8g.h 2018-04-14 12:26:01 -05:00
Scott Lahteine 29dda871cb Patch "upload_disk" to make python happy 2018-04-13 22:27:08 -05:00
Scott Lahteine 36b97bde9f clear_block_buffer, kill_current_block in quick_stop 2018-04-13 22:04:53 -05:00
Scott Lahteine 99282a46e9 Make sure ABL (manual) starts close to the bed 2018-04-13 20:19:30 -05:00
Roxy-3D 21f13f9e57
Stow Probe at end of G29 J3 2018-04-13 14:46:47 -05:00
KangDroid 6c535081ec [2.0.x] Add optional menu item to toggle software endstops (#10389) 2018-04-13 00:24:09 -05:00
Scott Lahteine 3c5c6d478a Prettify process_parsed_command 2018-04-13 00:23:11 -05:00
Scott Lahteine 0535ebc4d2 MESH_BED_LEVELING before PROBE_MANUALLY 2018-04-12 22:45:52 -05:00
Scott Lahteine bb7064cc30 Tweak MBL move to bed code 2018-04-12 22:43:02 -05:00
Chris Pepper cc6d41e1d3 Use a macro for HAL header redirection (#10380) 2018-04-12 20:25:08 -05:00
Luc Van Daele 12785583d0 [2.0.x] G33 MIN_STEPS_PER_SEGMENT (#10386) 2018-04-12 20:22:29 -05:00
Yunhui Fu c96412a78f [2.0.x] UTF-8 language translation support (#10213) 2018-04-12 20:14:01 -05:00
Scott Lahteine daa712455b Make sure MBL starts close to the bed
Fix #10390
2018-04-12 19:36:37 -05:00
Scott Lahteine 4c8751727a Fix M118 parameter handling
Fix #10388
2018-04-12 19:10:04 -05:00
Scott Lahteine 3bc179a16f Compress/update comments ubl_motion
…to fit more code on the screen and correct outdated commentary contrasting ABL.
2018-04-12 18:07:19 -05:00
Luc Van Daele 646aa20b43 Overhaul of G33 Delta Calibration (#8822) 2018-04-11 21:14:48 -05:00
Luc Van Daele ac2e0afb62 Low Point for delta calibration (#10363) 2018-04-11 18:59:46 -05:00
Eduardo José Tagle 57a899a412 [2.0.x] 6th-order jerk-controlled motion planning in real-time for AVR (#10373) 2018-04-11 18:13:42 -05:00
Bob-the-Kuhn 85014cd132 [2.0.x] LPC1768 - automatic selection of upload disk (#10374) 2018-04-11 14:41:16 -05:00
Scott Lahteine 8669dba5e6
Merge pull request #10172 from noingwhat/2.0.x-Filament-Change-Acceleration
[2.0.x] Filament load/unload add acceleration for Bowden
2018-04-11 00:39:11 -05:00
Scott Lahteine 472ab0cc24 Tweak RAMPS SDSS pins 2018-04-10 16:47:48 -05:00
LichtiMC b94c8defee Provide additional information about SMART-RAMPS board (#10353) 2018-04-10 04:02:55 -05:00
Scott Lahteine 6f8e228880 Add RESET_PIN to pins_RAMPS_SMART.h 2018-04-10 03:34:20 -05:00
Sean 2d9b0a66fe Add Filament Change accelerations 2018-04-09 23:57:27 -05:00
Scott Lahteine 71d3523254 Add Filament Change accelerations to example configs 2018-04-09 23:57:23 -05:00
Scott Lahteine 8b8ad14178 Add Z_PROBE_LOW_POINT to prevent damage 2018-04-09 17:23:03 -05:00
Scott Lahteine 82dafbba33 Add Z_PROBE_LOW_POINT to example configs 2018-04-09 01:55:05 -05:00
Roxy-3D a731a723e8 Better i3-2020 Z_PROBE_OFFSET_FROM_EXTRUDER 2018-04-08 21:26:36 -05:00
Roxy-3D 26cc12eaa4 Resolve corruption of Max7219 Debug LED Matrix 2018-04-08 21:26:36 -05:00
Scott Lahteine dca69efc11 Update Bed PID comments 2018-04-08 06:44:47 -05:00
Scott Lahteine 56486c5c0e Apply const to manage_inactivity 2018-04-08 04:00:26 -05:00
Scott Lahteine a6485456df Fix LIGHTWEIGHT_UI with UBL
See https://github.com/MarlinFirmware/Marlin/issues/10317#issuecomment-379100702
2018-04-08 03:24:22 -05:00
Scott Lahteine e02fc4f1d6 Better RESTORE_LEVELING_AFTER_G28 sanity-check
As suggested by @GMagician
2018-04-08 03:24:15 -05:00
Scott Lahteine 44a697ab04 Set STM32F1 TEMP_TIMER_FREQUENCY to 1K
Responding to https://github.com/MarlinFirmware/Marlin/pull/8833#issuecomment-379426803
2018-04-08 01:08:05 -05:00
Scott Lahteine cec6e19099 Add RepRapPro Huxley configuration
Based on #10343 by @indazoo
2018-04-08 00:37:18 -05:00
Scott Lahteine 9ff4e9e1e6 Patch _IS_HW_SPI so defined() works 2018-04-07 23:29:00 -05:00
Scott Lahteine cea398849e Tweak to gcode_line_error/return 2018-04-07 21:25:49 -05:00
etagle a29adde5c0 Implement BEZIER_JERK_CONTROL
Enable 6th-order jerk-controlled motion planning in real-time.
Only for 32bit MCUs. (AVR simply does not have enough processing power for this!)
2018-04-07 21:03:28 -05:00
Scott Lahteine 5932df7ea1 Add BEZIER_JERK_CONTROL to example configs 2018-04-07 21:03:22 -05:00
Lenbok 0e8242180d Chamber temperature monitoring and auto fan control.
This is an initial cut for feedback, updated for 2.0.x.

Chamber temperature is currently reported along with hot end and bed
temperatures to serial. The format is just like that used for hot end
and bed temperatures, but using 'C' prefix. As there is no heater,
target is always 0. Is this appropriate, is there a better way to report
chamber temperatures?

Chamber temperatures are not reported on the LCD in any way.

When auto chamber fan is enabled, it currently just uses the same
temperature threshold as the other auto controlled fans.

As the chamber temperature is not connected to any heater, it doesn't
undergo mintemp/maxtemp monitoring. This would need to change in the
future if chamber heating became a feature.
2018-04-06 23:09:06 -05:00
Scott Lahteine 5b3bda1c16 Add Chamber Temp options to example configs 2018-04-06 23:09:06 -05:00
Bob-the-Kuhn acda4ecb20 Fix DUE Trinamic SW/HW SPI sanity check (#10336) 2018-04-06 22:22:30 -05:00
Bob-the-Kuhn ab715c70d1 TMC SPI sanity-check and pins debugging (#10324) 2018-04-06 20:24:54 -05:00
Scott Lahteine 4dc7e64789 Update Slovak language
Based on #10313 by @rmoravcik
2018-04-06 20:23:20 -05:00
Scott Lahteine 0dccf9ea6a
Merge pull request #10318 from marcio-ao/pr-einsy-retro-tmc2130
[2.0.x] Fix TMC2130 DIAG1 active high, Einsy Retro
2018-04-06 20:18:34 -05:00
Marcio Teixeira 2efc072fdb Clear progress bar on completion (#10333)
Fix #10330
2018-04-06 20:13:19 -05:00
GMagician 6ce060cfe0 [2.0.x] Update language_it.h (#10322)
Updated to #10296
2018-04-06 20:07:46 -05:00
Marcio Teixeira 9356cf648f Added support for Einsy Retro
http://reprap.org/wiki/EinsyRetro
2018-04-06 19:48:46 -05:00
Marcio Teixeira 75037493fa Default active low for TMC2130 DIAG1 (#10294)
- Added sanity check to inform users to set the endstop to inverting
  when using SENSORLESS_HOMING
2018-04-06 19:48:46 -05:00
Scott Lahteine e8e60263c8 Scale feedrate (mm/s to deg/s) for SCARA 2018-04-06 19:47:48 -05:00
Scott Lahteine 051303ad42 Russian language updates
From #10311 by @anton-piliugin
2018-04-05 00:46:46 -05:00
Sean 2fa0a73c2c Implement filament change continuous purge 2018-04-04 20:57:51 -05:00
Scott Lahteine d133ad61f3 Add continuous purge to example configs 2018-04-04 20:56:18 -05:00
Scott Lahteine 4b25543633 Backtrace formatting cleanup 2018-04-04 20:24:39 -05:00
Bob-the-Kuhn 902c885782 Switch to TMC2130 compatible hardware SPI & misc (#10299) 2018-04-04 20:13:27 -05:00
Scott Lahteine 1c36606886 Fix MSG_HEATING_FAILED_LCD_BED macro evaluation 2018-04-04 19:01:22 -05:00
Scott Lahteine fe91514395
MBL should add z_offset regardless of fade (#10308) 2018-04-04 18:57:33 -05:00
Marcio Teixeira 8bc93c6f2b Improve heating/cooling LCD messages (#10293) 2018-04-04 18:29:27 -05:00
GMagician 21a47b50f4 Additional tool-change fixes (#10304)
Followup to #10257
2018-04-04 17:06:33 -05:00
Scott Lahteine f68b4265a6 Fix a probe pin definition 2018-04-02 21:52:34 -05:00
Yunhui Fu a019eebdd6 support utf8 unicode for test language (#10220) 2018-04-02 20:03:25 -05:00
Scott Lahteine 656219d867 Add configs for Creality CR-8 2018-04-02 20:02:04 -05:00
Karl Andersson 7cbbc2af7a [2.0.x] Optional heater signal inversion (#10260) 2018-04-02 19:37:41 -05:00
Marcio Teixeira 4d1a61335c [2.0.x] Fixed Makefile for Marlin 2.0 (#10255) (#10281)
* Fixed Makefile for Marlin 2.0 (#10255)

- Makefile now supports the new Marlin 2.0 directory hierarchy.
- RELOC_WORKAROUND is now automatically enabled based on avr-gcc version.

* Makefile support for U8glib and TMC2130Stepper

- Updated paths for oliver's U8glib 1.19.1
- Added option for teemuatlut's TMC2130Stepper 2.2.1
2018-04-02 19:36:27 -05:00
Scott Lahteine 241996d5d6
Merge pull request #10257 from thinkyhead/bf2_tool_change_debug 2018-04-02 19:33:45 -05:00
Scott Lahteine 4c79dc1093 Fix a Serial+EEPROM compile error
Fixes #10278
2018-04-02 03:11:20 -05:00
Scott Lahteine 93305a2d5e Fix some spellings 2018-04-02 03:03:37 -05:00
Scott Lahteine adcb87f0db Z Endstop Servo => Z Probe Servo 2018-04-01 23:54:21 -05:00
Scott Lahteine 4f0eafce8f Add more AVR boards to Makefile 2018-04-01 18:22:06 -05:00
Scott Lahteine 4a23069de9 Fix Ender 4 / CR-8 compilation
- Assign 243 (like EFB) as Ender-4/CR-8 board ID
- Add to `Makefile`
- Add to `pins.h`
2018-04-01 18:22:06 -05:00
Scott Lahteine 02f0f95d40
Handle disabled HYBRID_THRESHOLD in EEPROM (#10275) 2018-04-01 16:58:37 -05:00
Scott Lahteine 9ec2c03c5b Fix likely error in retract/recover
Addressing #10200
2018-03-31 23:01:13 -05:00
Scott Lahteine 49f384a2ab Note about MKS_MINI_12864 in sanitycheck 2018-03-31 22:52:23 -05:00
Scott Lahteine 2672120a97 Do a small raise for all move-back 2018-03-31 22:43:05 -05:00
Scott Lahteine 5acccbacc1 Simplified leveling-based tool change 2018-03-31 22:43:05 -05:00
Scott Lahteine 1a75165f35 For set_z_fade_height use set_bed_leveling_enabled 2018-03-31 22:43:05 -05:00
Scott Lahteine d1734a089a Split up tool_change for some setups 2018-03-31 22:43:05 -05:00
Scott Lahteine a9f94f260a Some RADDS pin updates 2018-03-31 22:15:24 -05:00
Scott Lahteine 31df43212c Use lcd_printPGM_utf in more places
Fix #10256
2018-03-31 20:49:20 -05:00
Scott Lahteine 7d8a46519f Output ABC for delta stepper counts 2018-03-31 20:13:32 -05:00
Scott Lahteine 6098efcc59 Use float62 for LCD edit of Z Fade 2018-03-31 20:03:09 -05:00
Scott Lahteine f6d13e2295 Allow Z_SAFE_HOMING sanity checks to handle floats 2018-03-31 19:01:56 -05:00
Scott Lahteine 889fd5f71f Backtrace minor cleanup 2018-03-31 18:59:36 -05:00
Scott Lahteine 53f0c7522a Symmetrical FWRETRACT Z Hop
Do the Z lift normally before setting Z back to its prior value. But do the Z lower using spoofing. This should produce proper symmetrical movement.
2018-03-30 15:54:01 -05:00
Scott Lahteine ac7e97f4fe Change order of inactive stepper disable/enable
This ensures that steppers that share an enable pin will only be disabled for a miniscule time.
2018-03-30 15:07:38 -05:00
Scott Lahteine 55e9b85ad6 Clear the "Wait for user" message set by M0/M1
See https://github.com/MarlinFirmware/Marlin/issues/10246#issuecomment-377146936
2018-03-29 18:38:12 -05:00
Scott Lahteine b6a55f0891 Temporary workaround for tool-change compile error
Pending a more complete solution to tool-change Z deviation.
2018-03-29 17:55:57 -05:00
Scott Lahteine b852781eba Fix BLTOUCH compile error
Followup to #10250
2018-03-29 17:55:57 -05:00
AnHardt c1f58a238d No delay in sensorless quick homing (#10254) 2018-03-29 16:10:20 -05:00
Scott Lahteine 1be955e52a Alert users about low Z jerk values 2018-03-28 23:08:33 -05:00
Scott Lahteine 9e4c037cef
Wait before turning off PRINTER_EVENT_LEDS at print end (#10248) 2018-03-28 22:59:28 -05:00
Scott Lahteine 8b7381b626 Clear sensorless homing in home_delta after first move-to-top 2018-03-28 22:01:42 -05:00
Scott Lahteine dbe2b6f7b0 Do moves towards endstops differently in do_homing_move 2018-03-28 22:01:42 -05:00
Scott Lahteine d573a2cada Fix pins_RAMPS.h for 32-bit platforms
Followup to 436e5b7
2018-03-28 22:01:20 -05:00
Scott Lahteine f04be05a14 "G28 Z Forbidden" => "Home XY first"
Some languages will need to be updated for proper phrasing
2018-03-28 21:51:15 -05:00
Scott Lahteine a97624dd81 Allow pinsDebug "Analog in" long int 2018-03-28 20:40:28 -05:00
Scott Lahteine 7b8bb2519e Fix gcode_line_error call
Followup to 3007eee
2018-03-28 20:29:41 -05:00
Scott Lahteine aa20b3ef7c Fix linear/3-point manual leveling buffer overrun
Fixes #10137
2018-03-28 18:41:22 -05:00
Alexey Shvetsov cbdc78ec0f Fix STM32 compilation with PlatformIO (#10245) 2018-03-28 18:35:20 -04:00
Scott Lahteine 9d2ea5d64b Undo German changes
See 941e9bd329 (commitcomment-28262166)
2018-03-28 17:05:14 -05:00
Scott Lahteine 2bc7f416ee Fix missing comma in tmc_sgt
Fixes #10209
2018-03-28 17:05:14 -05:00
Scott Lahteine 38378cd0e8 M218 with DELTA needs planner.h
Fix #10232
2018-03-28 17:05:14 -05:00
Scott Lahteine 3007eee22e Require a checksum when writing to SD
From #10204 by @adriancuzman
2018-03-28 17:05:13 -05:00
Bob-the-Kuhn 9656a82609 Fix G53/CNC_COORDINATE_SYSTEMS compilation, Travis testing (#10227) 2018-03-28 14:14:39 -04:00
Eduardo José Tagle 749f19e502 [2.0.x] Move backtrace to a shared location (#10237)
- And implement the `backtrace()` function call
2018-03-28 14:13:20 -04:00
xC0000005 7dc256432f Restore STM32F1 series to working order. (#10229)
The `_O2` attribute is no longer needed on the malyanlcd function, and the macros have broken timer numbers - reset this to a function to return the right device. Also fix the bit order cast in SPI.
2018-03-28 14:07:52 -04:00
Rob Power d1f14202a9 [2.0.x] NANODLP_Z_SYNC requires linear axes (#10240) 2018-03-28 14:03:34 -04:00
Scott Lahteine b287560258 Fix say_M603 2018-03-28 12:54:58 -05:00
Scott Lahteine 436e5b7ea3 Apply spacing in pins files 2018-03-28 12:52:08 -05:00
Scott Lahteine 4d533b9baa Update bq Hephestos 2 probe offset
From #10234 by @thopiekar
2018-03-27 21:05:03 -05:00
Bob-the-Kuhn 78df07ac71
Merge pull request #10221 from ejtagle/bugfix-2.0.x
[2.0.x] DUE: Several fixes to the backtracker
2018-03-27 03:26:10 -05:00
etagle 8934a2c49b Added some missing Thumb instructions to the traceback follower, so now it is able to traceback through switch() statements 2018-03-27 04:30:38 -03:00