Commit graph

3616 commits

Author SHA1 Message Date
unknown
8ea55323d8 Fix for not raising Z before homing X and Y 2016-02-15 14:52:04 -06:00
Scott Lahteine
b83e472bd3 Rename fpos_t to avoid libc conflict 2016-02-10 20:49:25 -08:00
Scott Lahteine
68457ee903 For Dual Y/Z use the next available extruder pins 2016-02-09 21:59:09 -08:00
Scott Lahteine
711e5db19a Tweak comment in process_next_command 2016-02-09 18:16:35 -08:00
Scott Lahteine
400e9329be Allow spaces after a code letter 2016-02-09 18:03:13 -08:00
Scott Lahteine
cdcb80f3c5 Allow no-space after initial command
Addresses issue #2715
2016-02-09 18:00:35 -08:00
AnHardt
6f473f7fc6 Repair N in ADVANCED_OK
Send the correct line number.
If no N was in the command - non't send an N.
2016-02-09 19:23:26 +01:00
AnHardt
efbd705eda Replace the "ok" in M280, M301, M304, M851 with output not including an "ok"
Replace the "ok" in M280, M301, M304, M851 with output not including an "ok"
to avoid senting two "ok"s for a single g-code.

Doing the same for M105 would break the input filters of the hosts.
For M105 the other "ok" is omitted.
2016-02-09 13:36:03 +01:00
Scott Lahteine
8e66028d25 Apply the ABL rotation matrix to the extruder offset. 2016-02-08 14:22:18 -08:00
esenapaj
ab5aa3fc92 Merge pull request #5 from MarlinFirmware/RCBugFix
Rc bug fix
2016-02-08 05:42:11 +09:00
esenapaj
27d918d836 Merge pull request #4 from MarlinFirmware/RCBugFix
Rc bug fix
2016-02-08 05:35:32 +09:00
Scott Lahteine
159ff94afd Remove obsolete HEATER_BED_DUTY_CYCLE_DIVIDER #2977 2016-02-07 08:02:11 -06:00
Ruwan J Egoda Gamage
1270fbfd38 Using SET_INPUT instead of pinMode 2016-02-07 07:58:52 -06:00
Ruwan J Egoda Gamage
b58083b0fa Getting rid of SDEXTRASLOW, SDSLOW variables. 2016-02-07 07:58:52 -06:00
Ruwan J Egoda Gamage
1833049b8a reusing millis() 2016-02-07 07:58:52 -06:00
Ruwan J Egoda Gamage
1b7c443628 Adding SDULTRASLOW variable.
Instead of changing SDEXTRASLOW variable to a slower speed,  the new
SDULTRASLOW is used for rigidbot panel.
2016-02-07 07:58:52 -06:00
Ruwan J Egoda Gamage
6f9e9c0e4f Cleaning up, getting rid of the fake encoder count variable. 2016-02-07 07:58:52 -06:00
Ruwan J Egoda Gamage
becbfe1065 Fixing Rigidbot LCD Panel Support 2016-02-07 07:58:52 -06:00
esenapaj
4882a7eded more suitable display format for delta printer 2016-01-29 18:38:25 +09:00
esenapaj
d7272e3f36 Merge pull request #3 from MarlinFirmware/RCBugFix
Rc bug fix
2016-01-29 05:43:22 +09:00
Scott Lahteine
62bad1b60f Merge pull request #2848 from japzi/RCBugFix
Fixing Rigidbot LCD Panel Support
2016-01-26 17:30:12 -08:00
esenapaj
59d345a3dd Update Configuration.h 2016-01-22 07:27:11 -06:00
esenapaj
b8f0c8a4c7 Update Configuration.h 2016-01-22 07:27:11 -06:00
esenapaj
df0d599c79 Update Configuration.h 2016-01-22 07:27:11 -06:00
esenapaj
a366697649 Update Configuration.h 2016-01-22 07:27:11 -06:00
Richard Wackerbarth
7c94c83765 Repair formula mangled by PR#1319 in Jan 2015 2016-01-15 10:06:27 -06:00
Naruto-kyun
2932602643 Update stepper.cpp
Forgot Z2_MIN_PIN
2016-01-15 16:50:43 +01:00
Ruwan J Egoda Gamage
06555febdd Using SET_INPUT instead of pinMode 2015-12-24 12:12:25 -05:00
esenapaj
8d2aa2368d Update Configuration_adv.h 2015-12-23 08:16:36 +09:00
esenapaj
0de5fcad0a Update Configuration_adv.h 2015-12-23 08:16:06 +09:00
esenapaj
1403b9acc0 Update Configuration_adv.h 2015-12-23 08:15:20 +09:00
esenapaj
5cf1c38ea1 Update Configuration_adv.h 2015-12-23 08:12:54 +09:00
esenapaj
04ab61bf40 Update Configuration_adv.h 2015-12-23 08:12:28 +09:00
esenapaj
39c62fbd6f Update Configuration_adv.h 2015-12-23 08:12:04 +09:00
esenapaj
efcb769003 Update Configuration_adv.h 2015-12-23 08:09:57 +09:00
esenapaj
992fbb831d Update Configuration_adv.h 2015-12-23 08:08:45 +09:00
esenapaj
5ee6fe6385 Update Configuration_adv.h 2015-12-23 08:07:12 +09:00
esenapaj
056daf00fc Update Configuration_adv.h 2015-12-23 08:06:15 +09:00
esenapaj
71aafb79a0 Update Configuration_adv.h 2015-12-23 08:03:54 +09:00
Ruwan J Egoda Gamage
2c9e0415c7 Getting rid of SDEXTRASLOW, SDSLOW variables. 2015-12-13 23:23:01 -05:00
Ruwan J Egoda Gamage
a64bcd53e9 reusing millis() 2015-12-13 22:06:03 -05:00
Ruwan J Egoda Gamage
e6cc232184 Adding SDULTRASLOW variable.
Instead of changing SDEXTRASLOW variable to a slower speed,  the new
SDULTRASLOW is used for rigidbot panel.
2015-12-13 15:47:10 -05:00
Ruwan J Egoda Gamage
83c4131ba3 Cleaning up, getting rid of the fake encoder count variable. 2015-12-13 15:28:40 -05:00
Ruwan J Egoda Gamage
5eeea2f611 Fixing Rigidbot LCD Panel Support 2015-12-13 15:28:40 -05:00
Richard Wackerbarth
f6950acb8e Residual unused variable — Backport 2015-12-10 19:48:08 -06:00
Richard Wackerbarth
7a670e3911 Improve planner & stepper PR #263 2015-12-10 07:24:37 -06:00
Richard Wackerbarth
58658c9279 Call the probe pin a probe pin and not a min endstop 2015-12-10 07:20:52 -06:00
Richard Wackerbarth
0fa3bac8ee If unused, just don’t define it. 2015-12-10 07:20:52 -06:00
Richard Wackerbarth
3b2973da6a Prepare Ramps for user redefinition 2015-12-10 07:20:52 -06:00
Richard Wackerbarth
1635613c25 Backport cosmetic 2015-12-10 07:20:52 -06:00
Richard Wackerbarth
0b429461d5 Back port Cosmetic changes 2015-12-10 07:20:52 -06:00
Richard Wackerbarth
0cebe85e65 Clean up spacing and duplicate entries
• Removing trailing whitespace
• Adjusting indention for better readability
• Removing duplicated entries
2015-12-10 07:20:52 -06:00
Richard Wackerbarth
e7b40bbe98 Change link to U8glib source 2015-12-10 06:33:29 -06:00
Richard Wackerbarth
e2da2b4105 Back port language translation 2015-12-10 06:31:41 -06:00
Richard Wackerbarth
4f314afaf0 Allow Thermistor #12 to be used on hotends also
//100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)

Caveat Emptor —- 
I’m not sure that this really makes sense,
but why keep someone from using it?
2015-12-10 06:31:31 -06:00
Scott Lahteine
60d5658da8 Revert nozzle_bed_fan_menu_items
For some reason that I cannot determine, using a sub-function causes
the Tune sub-menu to act strangely, yet replacing the function call
with its code content works perfectly.
2015-12-09 20:33:52 -06:00
AnHardt
57da1b8497 Host parseble output for M109, M190 and M303
Make the output of M105 more similar to Repetier.
Make the text-print pert of M105 an extra function to make it reusable. `print_heaterstates()`
Use `print_heaterstates()` in M019, M190 and M303
2015-12-07 15:37:53 -06:00
AnHardt
fcceb98191 Unglobalize no_wait_for_cooling 2015-12-07 15:34:26 -06:00
Wurstnase
78a347a01a change nx, ny, nz and ne from float to long
st_set_position takes long
```void st_set_position(const long& x, const long& y, const long& z, const long& e)```
2015-12-07 08:22:44 -06:00
Wurstnase
6d691aceee change dx, dy, dz and de from float to long
anything is long, we don't need float there
2015-12-07 08:22:24 -06:00
Richard Wackerbarth
6bfcb74c25 The probe stowing coordinates have changed 2015-12-05 19:31:59 -06:00
Wurstnase
0fbfb22506 Renaming delta speeds (PR2824)
dx -> dsx
dy -> dsy
dz -> dsz
de -> dse
2015-12-04 07:55:45 -06:00
AnHardt
8d1eeff021 Fix status LEDs update when reinitializing the display
Fix status LEDs update when reinitializing the display

By using the regular update function during init.

Fixing #2683
2015-12-03 07:18:35 -06:00
Richard Wackerbarth
5a54204f72 Marlin 1.1.0 Release Candidate 3 - 01 December 2015 2015-12-01 07:24:45 -06:00
AnHardt
bb4efcf603 Handle temp callbacks when THERMAL_PROTECTION_HOTENDS is not defined
by alternate definition for the callback macros
2015-12-01 07:21:52 -06:00
AnHardt
96d0d04b8f Update LCD buttons less frequently
Move slow_buttons_update into the LCD_UPDATE_INTERVAL block
lcd_implementation_read_slow_buttons() will then be executed ~10 times a
second.
2015-11-30 05:44:32 -06:00
Richard Wackerbarth
e293ea57f0 Unbalanced brackets in setPwmFrequency
This is a back port of the correct in issue #248
2015-11-30 05:44:32 -06:00
AnHardt
c956b52c4a Babystep Multiplier
Analog to https://github.com/MarlinFirmware/MarlinDev/pull/250 by
@RicardoGA

Restore the Babystep Multiplicator functionality and now it's available
for X/Y/Z
2015-11-30 05:43:10 -06:00
Richard Wackerbarth
956418c674 Kc is also a multi-PID parameter 2015-11-23 06:08:01 -06:00
AnHardt
33addc52a1 Suppress Z_MIN_PROBE_REPEATABILITY_TEST for DELTA and SCARA configurations (PR#2747)
For now Z_MIN_PROBE_REPEATABILITY_TEST is not possible for DELTA or SCARA
configurations.
This PR comments the feature out, where it is commented in by default.
2015-11-13 07:33:33 -06:00
AnHardt
8da2e98985 Split RAMPS 1.3 an 1.4 (PR#2741)
because of hardware differences on the SERVO0_PIN
2015-11-13 07:13:48 -06:00
AnHardt
be7167ed97 Change XY formatting on LCD (PR#2740)
According to #123 negative values for XY at or below -100 are displaying incorrectly, dropping the first digit. Deltas can easily have XY values in this range. This PR adds a function to display floats/ints formatted like `_123`, `-123`, `_-12`, or `__-1` as appropriate and applies it to the XY coordinates on Hitachi displays. It also moves the Z value to the right to be consistent with the XY formatting.
2015-11-13 06:46:11 -06:00
Luis Correia
e7099ea597 Fix Portuguese (Portugal) strings (PR#2700)
Align strings with release
2015-11-12 00:08:42 -06:00
Scott Lahteine
754b13d8fe Patch issue #2315 2015-11-12 00:03:22 -06:00
Scott Lahteine
dbd4c17096 Init Kp, Ki, Kd to 0 2015-11-12 00:03:22 -06:00
Scott Lahteine
644c376e84 Use binary OR with endstop bits 2015-11-12 00:03:22 -06:00
Scott Lahteine
54a39d8c1a Use a ternary in qr_solve.cpp 2015-11-12 00:03:22 -06:00
Scott Lahteine
17c23bbaf3 Shorten gcode_M221 yet function the same 2015-11-12 00:03:22 -06:00
Scott Lahteine
c0e791dbe9 Only look for "N" line number as first parameter 2015-11-12 00:03:22 -06:00
Scott Lahteine
b4af4441c5 Clean up watchdog impl. 2015-11-12 00:03:22 -06:00
Scott Lahteine
8f16563bbd Use "defined" with LCD_PIN_BL and LCD_PIN_RESET 2015-11-12 00:03:22 -06:00
Scott Lahteine
6fa7e24af3 Use "UNUSED" to squash compiler warnings 2015-11-12 00:03:22 -06:00
Scott Lahteine
d5b7c595ae Use static locals in utf_mapper.h 2015-11-12 00:03:21 -06:00
Scott Lahteine
9bdab4f3a8 Clean up "else" and other spacing 2015-11-12 00:03:21 -06:00
Scott Lahteine
9b23490f01 Clean up spacing in configs 2015-11-12 00:03:21 -06:00
esenapaj
c6c37abd41 Update language_kana.h 2015-11-12 00:00:51 -06:00
esenapaj
c24045475a Update language_kana_utf8.h 2015-11-12 00:00:32 -06:00
Richard Wackerbarth
25d636c9e0 Compiler issues (PR#2696) 2015-11-11 23:52:11 -06:00
AnHardt
47401ec97b MSG_EXTRUDER_SWITCHED_OFF was renamed to MSG_REDUNDANCY
in language.h, but was not renamed here. If TEMP_SENSOR_1 is enabled as redundant then
an error is thrown that MSG_EXTRUDER_SWITCHED_OFF is not defined.

Originaly by @12dstring
2015-10-08 10:45:11 -05:00
Scott Lahteine
ba6a243197 DEBUG message has no parameter (PR#2671) 2015-10-03 22:03:03 -05:00
Scott Lahteine
0c7f7ebcfb Styling adjustments (PR#2668 & PR#2670)
Keep "astyled" reformatting
2015-10-03 22:02:45 -05:00
Rafa Couto
b5fb7075b9 Galician (gl) language. 2015-09-30 14:46:01 -05:00
Richard Wackerbarth
7b4bdc0203 DUAL_X_CARRIAGE motor enabling
As noted by @darkjavi et.al. in #103, the E1 motor was not being enabled in planner.cpp when using DUAL_X_CARRIAGE. This patch enables and disables E1 as it should.
2015-09-30 04:31:19 -05:00
Richard Wackerbarth
91b5156b3e Marlin 1.1.0 Release Candidate 2 - 29 September 2015 2015-09-29 20:28:41 -05:00
Richard Wackerbarth
03f0edb57e Fix high LCD status screen update frequency (PR#2655) 2015-09-28 11:07:33 -05:00
KiteLab
0ad25c6665 Hint for changed behaviour of SDSUPPORT 2015-09-28 11:07:33 -05:00
Richard Wackerbarth
e01f5e1ef7 Cleanup 2015-09-17 10:44:23 -05:00
Mike Cochrane
5e36b64635 SDEXTRASLOW for some SD card readers (PR#176)
Add SDEXTRASLOW which runs the SD card at SPI_QUARTER_SPEED. Quarter speed is needed for RIGIDBOT_PANEL
2015-09-14 07:58:08 -05:00
Scott Lahteine
5d65a36dee Give lcd_sd_status an UNKNOWN state (PR#180) 2015-09-14 06:32:27 -05:00
fmalpartida
0f149ea0c6 LCD home button causes repeated homing (PR#175)
Fix: increased debounce delay.
2015-09-14 06:31:49 -05:00
Scott Lahteine
b825567e0f Drop www. from marlinfirmware.org (PR#175) 2015-09-14 06:28:53 -05:00
Scott Lahteine
db27e67580 Apply PID_ADD_EXTRUSION_RATE to extras 2015-09-12 07:53:20 -05:00
Scott Lahteine
bc50db9cf6 Implement PID_ADD_EXTRUSION_RATE 2015-09-12 07:53:20 -05:00
Scott Lahteine
cffb2d457e Cleanup file formatting 2015-09-12 07:48:27 -05:00
Scott Lahteine
7ac7ddbf20 Show nozzles, heaters, and extruders numbered 1-4 2015-09-12 07:40:18 -05:00
Scott Lahteine
5bc480fee8 Fix Move E menu items 2015-09-12 07:33:49 -05:00
Scott Lahteine
fc882c34a3 Init lcd_sd_status as false to force lcd_update test
Replaces #145 which is way out of date
2015-09-12 07:32:20 -05:00
Scott Lahteine
e27dd5c22d Conditionalize functions that rely on SDSUPPORT 2015-09-12 07:30:09 -05:00
Scott Lahteine
fabf3ae4a0 Add final Z raise after Delta probe 2015-09-12 07:23:24 -05:00
Petr Zahradnik
8c768a76a2 Create language_cz.h
Czech language translation.
2015-09-12 07:18:05 -05:00
Petr Zahradnik
5b9010965d Update language.h
Added comment for Czech language (associated with file language_cz.h).
2015-09-11 04:43:54 +02:00
Scott Lahteine
89fb778684 Fix up probe pin define and test 2015-09-10 10:54:03 -05:00
Scott Lahteine
558665cd90 Constrain Tune > Nozzle/Flow menu items 2015-09-10 08:47:11 -05:00
Scott Lahteine
9f462f0cf5 Hack to address stuttering caused by ISR not finishing in time
(PR #138)

When the ISR does not finish in time, the timer will
wrap in the computation of the next interrupt time.

This hack replaces the correct (past) time with a time not far in the future.
2015-09-10 08:26:17 -05:00
Scott Lahteine
8b3d63c423 Unify Delta XYZ homing rates
As noted in #130 allen key probe stow rate is based on homing rates,
but homing rates were left out of most delta configs. This unifies the
XYZ homing rates and applies the unified rates to allen key movements.
2015-09-08 13:11:55 -05:00
Scott Lahteine
7c72b57313 Unify manual feedrate and Fix LCD MANUAL_FEEDRATE (PR#128)
As noted by @o-lampe at https://github.com/MarlinFirmware/MarlinDev/issues/114#issuecomment-136757614 the `MANUAL_FEEDRATE` for Delta Z should be the same as XY.
2015-09-08 13:11:55 -05:00
Scott Lahteine
f690b82343 Remove extra MAX_FREQ_TIME define (PR#148) 2015-09-08 13:11:12 -05:00
Scott Lahteine
a4c78ae786 Add E1 pins to SENSITIVE_PINS for Dual Y or Dual Z 2015-09-07 09:41:06 -05:00
Scott Lahteine
a39fadf876 Update kossel-pro example config (again?) 2015-09-07 09:41:06 -05:00
Scott Lahteine
34e0a8d848 Move Y2 and Z2 pins defines to pins.h 2015-09-07 09:41:06 -05:00
Scott Lahteine
28599c51c7 Wrap Dual Y options in a conditional 2015-09-07 09:41:05 -05:00
Scott Lahteine
11a065c0ca Remove Z2 pins overrides from Configuration_adv.h 2015-09-07 09:41:05 -05:00
Scott Lahteine
f7f6b5faae Fix lcd_move_e compile error (PR#143)
Fix a compile error introduced in #98
2015-09-07 09:36:05 -05:00
Scott Lahteine
2b30e8ac99 Conditionals for ULTIPANEL without SDSUPPORT 2015-09-06 02:04:49 -05:00
Scott Lahteine
7c7a4051fe Disable SDSUPPORT by default
As noted in #133 you can’t disable `SDSUPPORT` with `MAKRPANEL`,
`PANEL_ONE`, `MINIPANEL`, or `ULTIPANEL`. This patch makes it possible
to disable `SDSUPPORT` on these controllers and then disables it by
default.

Users of these controllers will now need to enable `SDSUPPORT` in their
configurations as others currently do.
2015-09-06 02:04:49 -05:00
Eric Kuzmenko
b23d765991 Added Extrude From Multiple Extruders from LCD feature 2015-09-05 05:33:18 -05:00
Christian Lefrançois
8347a9d6e4 Fix HOMING_BUMP_DIVISOR for deltas configuration
* Re-bump speed divisor should be the same for delta printer.
2015-09-03 09:26:28 -05:00
Scott Lahteine
703df2cb6c Fix error message for probe region sanity check 2015-09-03 03:27:47 -05:00
Shane Francis
4c8330c15c Trim Adjustments for Delta Configurations 2015-09-03 01:05:33 -05:00
Scott Lahteine
962120d1d2 Fix spacing in some conditional blocks 2015-08-27 20:59:09 -05:00
Richard Wackerbarth
20b4772155 Create DEBUG_LEVELING_FEATURE 2015-08-27 20:52:08 -05:00
Scott Lahteine
194f98ff95 Debug messages for homing and leveling 2015-08-27 20:52:08 -05:00
Richard Wackerbarth
6292d9e815 Rename ENABLE_AUTO_BED_LEVELING
With the introduction of the #if ENABLED(…)

reads better than
2015-08-27 20:52:08 -05:00
Richard Marko
91fd66ffba add Lulzbot TAZ4 example configuration (PR#104) 2015-08-27 08:36:43 -05:00
Wurstnase
7a275773ee remove colon in utf_mapper.h (PR#106) 2015-08-27 07:15:23 -05:00
Chris Bruner
6b4b6fa315 update for newest version of U8glib_Arduino 2015-08-26 19:52:59 -05:00
Christian Lefrançois
9897a9147c Update ABL comments (PR#95)
* Updates the auto bed leveling comments ONLY.
* Renames "Z probe" word usage in //comments and #errors properly.
2015-08-26 05:51:38 -05:00
Christian Lefrançois
a7822e3ff7 Some renaming of Z_PROBE to Z_MIN_PROBE (PR#91)
* Fix a couple of renames omission and macro expansion errors.
2015-08-20 06:04:46 -05:00
Richard Wackerbarth
ad90e851b3 Use a small unsigned integer type 2015-08-16 06:56:47 -05:00
Richard Wackerbarth
29b456ae07 Suppress some compiler warnings 2015-08-16 06:56:47 -05:00
Scott Lahteine
23d742bf06 Don't free the stack array plane_equation_coefficients (PR#83) 2015-08-16 06:53:24 -05:00
Scott Lahteine
e3b1e08777 Patch G30 to use raise_z_for_servo (PR#73) 2015-08-15 21:47:04 -05:00
Scott Lahteine
a1eb90d5c0 Save another 30 bytes in gcode_SET_Z_PROBE_OFFSET 2015-08-12 21:26:32 -05:00
Scott Lahteine
91122277f4 Reduce gcode_SET_Z_PROBE_OFFSET by 88 bytes 2015-08-12 21:26:25 -05:00
AnHardt
5707a2c3d5 indexindexIntoAB is only vald for !DELTA 2015-08-11 17:32:11 -05:00
AnHardt
d8860f9ad9 Alway end at the same point
Always end at [RIGHT_PROBE_BED_POSITION, BACK_PROBE_BED_POSITION]
Regardles the evennes of auto_bed_leveling_grid_points.
2015-08-11 17:32:11 -05:00
AnHardt
4ca8f4a9a7 Always zigzag
Use the shortest way between probing-points.
2015-08-11 17:32:11 -05:00
AnHardt
3d23424121 Add array indexIntoAB[xx][yy]
and use it.
2015-08-11 17:32:11 -05:00
AnHardt
e2d69f66b2 Make Z_PROBE a Z_MIN_PROBE (PR#65)
Currently we use the probe exclusively as a device to find the build platform(bed).
For the currently supported setups this means, we use it as a additional min-endstop.
A triggered when not deployed probe disturbs the homing process for max-endstops.

Rename ENDSTOPPULLUP_ZPROBE to ENDSTOPPULLUP_ZMIN_PROBE
Rename Z_PROBE_ENDSTOP_INVERTING to Z_MIN_PROBE_ENDSTOP_INVERTING
Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP
Rename DISABLE_Z_PROBE_ENDSTOP to DISABLE_Z_MIN_PROBE_ENDSTOP
Rename Z_PROBE_REPEATABILITY_TEST to Z_MIN_PROBE_REPEATABILITY_TEST
Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP
Adjust comments accordingly
Remove Z_MAX  check for the probe in update_endstops().

Using an delta related idea of @clefranc from #61,
extended to the general change for all setups.

Tested with Prusa i3, max-z-endstop and permanently triggered z-probe.
Worked for @clefranc's delta.
2015-08-11 14:41:36 -05:00
AnHardt
6a6e863a47 Resolve #2581 by adding a missed ';' (PR#67) 2015-08-10 12:51:59 -05:00
RicardoGA
e09ff79635 Update pins_RAMPS_13.h (PR#64)
Now all ramps configuration can enable Filament sensor not only EEB
2015-08-10 05:53:01 -05:00
Fourmi
e6aed7bb4e Update thermistortables for Hisens Thermistor (PR#2588) 2015-08-09 18:11:14 -05:00
Richard Wackerbarth
9d8cc24abf Continue from the line following the M999 (PR#60)
If the printer is going to accept the M999,
then it should continue from that line number.
2015-08-08 08:08:02 -05:00
wurstnase
f3ab1dba54 Z babystepping for coreXY (PR#47)
only X and Y were not implemented
2015-08-04 20:10:09 -05:00
Richard Wackerbarth
35afea1c0e Restore test
PR#2572 Changed this because of faulty Boolean Logic

NOT(A OR (NOT B) OR (NOT C)) !=

(NOT A) AND ((NOT B) OR C))


Besides, the compiler should be smart enough to
optimize this without help from the programmer
2015-08-04 15:22:56 -05:00
Scott Lahteine
6af75f4b5d Squish down deprecated tests in sanity check 2015-08-03 16:04:48 -05:00
Scott Lahteine
edeb58288e Use PIN_EXISTS in sanity check 2015-08-03 16:04:48 -05:00
Scott Lahteine
c30b7693e0 Clean up RUMBA pins conditions 2015-08-03 16:04:48 -05:00
Scott Lahteine
46453905d6 Apply remaining ENABLED/DISABLED conditionals 2015-08-03 16:04:48 -05:00
Richard Wackerbarth
b227d8c128 Supply a VERSION in a short form for displays
The long descriptor will still be available in M115
2015-08-03 08:21:09 -05:00
Richard Wackerbarth
cd7828a928 This will be the 1.1.0 Release rather than 1.0.3 2015-08-03 08:08:38 -05:00
Richard Wackerbarth
4e2f5618c1 Pick up Default_version when needed 2015-08-03 08:08:37 -05:00
Richard Wackerbarth
329acc852e Canonize Option flag USE_AUTOMATIC_VERSION 2015-08-03 08:08:37 -05:00
Richard Wackerbarth
5a11d32a85 Move deprecation test to SanityCheck.h 2015-08-03 08:08:37 -05:00
Richard Wackerbarth
7bb7a52940 Bring config up-to-date 2015-08-03 07:35:33 -05:00
AnHardt
244ea2014a Boot-screen for text-displays improvements
Centred the logo for 16x4 and 20 x4.
Moved version to the bottom line
Code shrink to 704 bytes.
2015-08-03 07:13:00 -05:00
AnHardt
80f2a20842 Enable bootscreen in all Configurations 2015-08-03 07:13:00 -05:00
AnHardt
2684d061ed Scroll too long strings on bootscreen 2015-08-03 07:13:00 -05:00
AnHardt
4f46df5dab Make bootscreen configurable for the graphic displays
Saves about 473 byte of progmem and 28 bytes of RAM.
2015-08-03 07:13:00 -05:00
AnHardt
09571b7753 Boot-screen for the character displays
Uses about 488 byte of progmem and 32 byte of RAM.
For that configurable.
2015-08-03 07:13:00 -05:00
Richard Wackerbarth
866efc14fe Add Danish translations 2015-08-03 07:06:17 -05:00
Scott Lahteine
267f3479d7 Adjust spacing in pins_RAMPS_13.h 2015-08-02 23:26:58 -05:00
Scott Lahteine
56702e7bb9 Define servo pins just like other pins 2015-08-02 23:26:58 -05:00
Richard Wackerbarth
4b9d5cd352 Use lowercase names for serial instances 2015-08-02 23:01:39 -05:00
Scott Lahteine
1e2deff4fd Rename BTENABLED to BLUETOOTH
- For some reason it’s easy to forget what BT stands for, but it
doesn’t need an abbreviation.
2015-08-02 22:56:50 -05:00
Scott Lahteine
68055a5959 Include RIGIDBOT_PANEL in Conditionals 2015-08-02 22:26:41 -05:00
George Djabarov
f8ed3a835d Added comment with the RigidBot Big bed size 2015-08-02 22:13:37 -05:00
George Djabarov
7deae6b6be Updated RigidBot example configuration
- The default serial baud rate of 115200
- The regular RigitBot bed size 254mm/248mm/254mm
- Single stock extruder
- Stock termistors for extruder and hotbed
- Stock Min X/Y/Z stops. Max stops not connected
- Stock 32 teth tooleys (stock axis steps)
- No auto bed leveling
- No screen
2015-08-02 22:13:37 -05:00
Scott Lahteine
5418faa1f9 Add sanity checks for old names 2015-08-02 22:09:08 -05:00
Scott Lahteine
f03e063750 Rename BEEPER to BEEPER_PIN
For consistency with other pins, allowing use of `PIN_EXISTS` macro.
2015-08-02 22:09:08 -05:00
Scott Lahteine
270c766de2 SDCARDDETECT -> SD_DETECT, added docs
- `SD_DETECT_PIN` replaces `SDCARDDETECT`
- `SD_DETECT_INVERTED` replaces `SDCARDDETECTINVERTED`
- Revise the description of `SD_DETECT_INVERTED`
- Add a note about the override of `SD_DETECT_INVERTED` in
`Conditionals.h`
2015-08-02 21:59:41 -05:00
Scott Lahteine
496fc28dc3 Tweaks to pins comments 2015-08-02 21:34:13 -05:00
Scott Lahteine
8d3b74cc6e Rename SDCARDDETECT to SDCARDDETECT_PIN
- Rename the pin so it can be tested with `PIN_EXISTS`
- Fix some incorrect tests for `SDCARDDETECT`
2015-08-02 21:34:13 -05:00
Scott Lahteine
0f5ada8cbd Group the fail case in one negation (PR#2572) 2015-08-01 18:55:50 -05:00
AnHardt
7ddf1cda1d Improve condition for SERVO_LEVELING (PR#2570) 2015-07-31 22:41:34 -05:00
Richard Wackerbarth
f32048b8f5 In for a penny, in for a pound 2015-07-31 17:13:53 -05:00
Scott Lahteine
e944f960de Add a sanity check for old name "BEEPER" 2015-07-31 17:13:53 -05:00
Scott Lahteine
8ebf0b92be Spacing adjustments in some pins files 2015-07-31 17:13:53 -05:00
Scott Lahteine
94a796c8cc Rename BEEPER to BEEPER_PIN
For consistency with other pins, allowing use of `PIN_EXISTS` macro.
2015-07-31 17:13:53 -05:00
Richard Wackerbarth
b217474eab Compiler Complaints about concatenated tokens (PR#2566) 2015-07-31 17:08:44 -05:00
Scott Lahteine
2460f82d8b Make proper distinction between BEEPER and HAS_BUZZER 2015-07-31 01:24:33 -05:00
Scott Lahteine
58cfcd4239 Overridable Options - Part 5
Apply `ENABLED` / `DISABLED` macros to files needing only a small
number of changes.
2015-07-31 01:24:20 -05:00
Scott Lahteine
5e834352a9 Overridable Options - Part 11 (PR#2563)
Apply `ENABLED` / `DISABLED` macros to EEPROM-related files.
2015-07-31 01:07:04 -05:00
Scott Lahteine
bf6eb93c61 Overridable Options - Part 10 (PR#2562)
Apply `ENABLED` / `DISABLED` macros to planner files.
2015-07-31 01:06:29 -05:00
Scott Lahteine
51e89a269c Overridable Options - Part 9 (PR#2561)
Apply `ENABLED` / `DISABLED` macros to temperature-related files.
2015-07-31 01:05:55 -05:00
Scott Lahteine
c35fb88094 Overridable Options - Part 8 (PR#2560)
Apply `ENABLED` / `DISABLED` macros to stepper-related files.
2015-07-31 01:05:22 -05:00
Scott Lahteine
0d8989fc14 Overridable Options - Part 7 (PR#2559)
Apply `ENABLED` / `DISABLED` macros to LCD-related files.
2015-07-31 01:04:37 -05:00
Scott Lahteine
b4abb0ae7f Apply ENABLED / DISABLED to Marlin core files (PR#2558) 2015-07-31 01:03:58 -05:00
Scott Lahteine
c0d7ea3e7e Overridable Options - Part 4 (PR#2556)
Apply `ENABLED` / `DISABLED` / `HAS_SERVOS` macros to pins files.
2015-07-31 00:44:53 -05:00
Scott Lahteine
4b40964064 Overridable Options - Part 3 (PR#2555)
Apply `ENABLED` / `DISABLED` macros to language-related files.
2015-07-31 00:19:13 -05:00
Scott Lahteine
32683b282b Include configurator copies of configs 2015-07-31 00:03:36 -05:00
Scott Lahteine
37d1879386 Apply overridables to Configuration files 2015-07-31 00:03:36 -05:00
Scott Lahteine
9d151bb61b servo_endstop_angles -> servo_endstop_angle 2015-07-30 23:35:57 -05:00
Scott Lahteine
9334479aeb Minor cleanup of Conditionals.h 2015-07-30 23:35:57 -05:00
Scott Lahteine
1f63293624 servo_endstops -> servo_endstop_id 2015-07-30 23:35:57 -05:00
Scott Lahteine
edaaead7e0 Fix comment about SERVO_ENDSTOP_ANGLES 2015-07-30 23:35:57 -05:00
Scott Lahteine
ed4a6371ad Add HAS_SERVO_ENDSTOPS to simplify conditonals 2015-07-30 23:35:57 -05:00
Scott Lahteine
70be61d416 Reset filament_size with a loop 2015-07-30 23:31:58 -05:00
Scott Lahteine
ae9274be05 Fix minor compiler warnings in for loops 2015-07-30 23:31:58 -05:00
Scott Lahteine
c7c8cfed6f Complete M200 output with M503
- The contents of EEPROM include filament diameters even with
Volumetric disabled. This change makes `M503` display the full
volumetric settings so that playing back the output of `M503 S0` will
fully restore them.
2015-07-30 23:31:58 -05:00
Scott Lahteine
4a58e447a1 Add array size to servo_endstop_angles (PR#2553) 2015-07-30 23:27:38 -05:00
Andrew Lenharth
a0ae9e30df don't pass integer by reference, inefficient. (PR#2547) 2015-07-30 17:51:12 -05:00
AnHardt
d03f037a92 Get rid of malloc() and free() (PR#2549)
Just the minimal changes to qr_solve.cpp and .h to get rid of malloc() and free().

Saves about 656 bytes of progmem (library-code)
and 22 bytes for static variables.

Should use exactly the same amount of stack as it did before on the heap.
2015-07-30 17:50:31 -05:00
Scott Lahteine
3b2b2313ff Combine if block related to SERVO_ENDSTOPS 2015-07-30 16:39:05 -05:00
Scott Lahteine
0af2a80e06 Make SERVO_ENDSTOP_ANGLES 2-dimensional 2015-07-30 16:38:56 -05:00
Richard Wackerbarth
525d0dc239 Configurator is out-of-date AGAIN (PR#2550) 2015-07-30 16:36:01 -05:00
Richard Marko
dd22cbbfb8 makefile: add buzzer.cpp (PR#2479) 2015-07-30 07:56:44 -05:00
Scott Lahteine
9f48798ffd Replace ENABLED with DEFINED for SERVO_ENDSTOPS (PR#2542) 2015-07-30 07:55:29 -05:00
Richard Wackerbarth
ae00fad75b Rename as M100 2015-07-27 20:31:59 -05:00
Richard Wackerbarth
a401d738df There is an echo in here 2015-07-27 20:31:59 -05:00
Richard Wackerbarth
ed7d45e8f5 Memory watcher 2015-07-27 20:31:59 -05:00
AnHardt
d17f7ebc8a Multiply WATCH_TEMP_PERIOD by 1000UL (PR#2535)
instead of 1000.  Else we get errors with times over 32 seconds.
2015-07-27 20:30:53 -05:00
Scott Lahteine
bea6739774 Don't include Z_RAISE_AFTER_PROBING if not used (PR#2527) 2015-07-27 20:24:33 -05:00
Scott Lahteine
81bba7ed88 More sanity checking for extruder requirements (PR#2531) 2015-07-27 10:14:43 -05:00
AnHardt
87a97f3724 Fix conditions for display strings 2015-07-26 20:41:21 -05:00
AnHardt
aaccea0260 Shift some display only strings from language.h to lenguage_en.h
and translate them to German.
2015-07-26 20:41:15 -05:00
Scott Lahteine
e4c01f1c7e Simplify init with ARRAY_BY_EXTRUDERS1 macro (PR#2507) 2015-07-26 20:40:27 -05:00
Scott Lahteine
ab6f1fdf8b Move & document ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED (PR#2528)
As suggested in #2521
- Move `ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED` because `SDSUPPORT` is
also required.
- Add a note that endstops must be enabled for the feature to have any
effect
2015-07-26 20:36:37 -05:00
Richard Marko
1183c10a2e makefile: drop -q -q (much quiet) from avrdude flags
Annoying when trying to figure out if uploading
actually does something.
2015-07-26 20:31:31 -05:00
Richard Marko
0e064357f4 makefile: use /etc/avrdude/avrdude.conf on linux
No need to look for arduino specific avrdude configuration
as distributions ship their own avrdude.conf file that
is compatible with arduino.
2015-07-26 20:31:31 -05:00
Scott Lahteine
bcb7d5a149 Improve sanitycheck for TEMP_SENSOR_1 2015-07-25 21:17:36 -05:00
Scott Lahteine
5b24f59401 Add sanity checks for temp sensors 2015-07-25 21:17:36 -05:00
AnHardt
fd0e81b0c7 Distinguish between BUZZER and SPEAKER (PR#2513)
A speaker needs a AC or a pulsed DC to make a sound, a buzzer only needs a DC.
A buzzer has it's own resonator. It works in most cases to feed the buzzer with a pulsed DC, but the sound will not be as loud as with pure DC.

There seem to be boards where the BEEPER-pin is not able to handle a PWM. Obviously intended for a buzzer.
To make these board able to handle a speaker

* replace the PWM based tone()-function again with a on-delay-off-delay loop.

Hopefully the last time I touch the beeper code.
2015-07-24 22:10:04 -05:00
Scott Lahteine
e2957df05c Shorthand for do_blocking_move_to 2015-07-24 22:07:41 -05:00
Scott Lahteine
819c5b9b50 Adjust comment on Z adjustment 2015-07-24 22:07:41 -05:00
Scott Lahteine
5a7356b6fc Patch for G29 final Z position
Include all the necessary pieces to get the final Z position after
probing the bed, and add commentary about other possible changes.
2015-07-24 22:07:41 -05:00
AnHardt
088e09e052 Add forgotten Marlin_main.cpp 2015-07-24 22:04:49 -05:00
AnHardt
8b876241bd Some more servo code tweaks
Just set up the pin. Don't move to a random position.

Simplify servo::move()
* servo::move() does not need the pin parameter - The pin is set during servo_init() with attach().
* servo::move() does not need a return value.

SERVO_LEVELING is the wrong condition to deactivate the servos.

Remove some temporary (Servo *) variables.
SanityCheck for the servo indexes.
2015-07-24 22:04:49 -05:00
Scott Lahteine
b116c096bd Reduce set_homing_bump_feedrate, save 42 bytes (PR#2512)
Updates to `set_homing_bump_feedrate`:
- Move the string into Program Memory, reduce length by 31 bytes
- Use an auto to get the divisor, adjust it on error
- Set feedrate once, at the end
2015-07-24 22:00:25 -05:00
Scott Lahteine
f7e7862588 Better Sanguinololu & Graphical Controller (PR#2504)
- Change suggested at
https://github.com/MarlinFirmware/Marlin/issues/2482#issuecomment-123553
266
2015-07-23 23:47:07 -05:00
Scott Lahteine
a1154d4a20 Enable Y and sanity-check CoreXZ (PR#2509) 2015-07-23 23:46:27 -05:00
Scott Lahteine
932f1c109e Move servos to the top in pins_MEGACONTROLLER.h 2015-07-23 22:51:41 -05:00
Scott Lahteine
90f8ddfc1e Apply MINIPANEL to other configs 2015-07-23 22:51:41 -05:00
AndySze
00dbf69b6d add MINIPANEL defines 2015-07-23 22:51:40 -05:00
AndySze
8ac5e56934 fixed some format problems and cleaned code 2015-07-23 22:51:40 -05:00
AndySze
eef595aa64 add makerlab mega controller pin configs 2015-07-23 22:51:40 -05:00
AnHardt
4e14e152fa Add Travis tests for CORXY and COREXZ 2015-07-23 19:52:48 -05:00
AnHardt
27d7d2ccab Correct bracketing for COREXY-XZ 2015-07-23 19:52:21 -05:00
Scott Lahteine
469843427d Reduce code in gcode_M81 (PR#2497) 2015-07-23 08:14:00 -05:00
Scott Lahteine
c66955aaf9 Mark unchanging arrays as const (PR#2494)
The compiler may be able to optimize if it knows an array won’t be
changing.
2015-07-22 21:37:37 -05:00
Scott Lahteine
278aa15301 Add COUNT macro and apply 2015-07-22 18:16:05 -05:00
Scott Lahteine
d85861d296 Move macros, add ENABLED/DISABLED, add includes 2015-07-22 18:16:05 -05:00
Scott Lahteine
17960fd2b0 Neaten up pins_MEGATRONICS.h (PR#2493) 2015-07-22 17:23:22 -05:00
Scott Lahteine
aac2b9aa9d Reduce code in gcode_M84 (PR#2492)
`gcode_M84` only needs to call `finishAndDisableSteppers`, which calls
all the other functions.
2015-07-22 17:22:01 -05:00
Scott Lahteine
4971fa73f9 Add a sanitycheck error for old servo settings (PR#2491)
- Documentation solution for #2476
2015-07-22 16:35:10 -05:00
Scott Lahteine
96ace72ddc Servos attach/detach based only on servo config
Assuming #2470 fixed up the main issue.
2015-07-22 16:34:26 -05:00
Richard Wackerbarth
b80a6a8d31 Correct Kossel Pro Configuration_adv (PR#2473) 2015-07-22 16:32:08 -05:00
Scott Lahteine
000a6fce46 Extract update_endstops from stepper ISR (PR#2474) 2015-07-19 18:33:18 -05:00
Scott Lahteine
e83eac312e Move plan_arc next to prepare_move 2015-07-19 16:18:46 -05:00
Scott Lahteine
5c5936508d G2/G3 Arcs for Delta
- Update prepare_move_delta to take a target argument
- Add Delta support to plan_arc
2015-07-19 16:18:46 -05:00
Scott Lahteine
9f53e2f0c9 Implement COREXZ in stepper.cpp and planner.cpp 2015-07-19 16:17:03 -05:00
Scott Lahteine
fa00e1d97f Explode conditions common to corexy and cartesian 2015-07-19 16:17:03 -05:00
Scott Lahteine
c7dd5527b4 Add a C_AXIS and Z_HEAD to support COREXZ 2015-07-19 16:17:03 -05:00
Scott Lahteine
129f986ccf Add COREXZ option to configurations 2015-07-19 16:17:03 -05:00
Scott Lahteine
69b0490b77 Show minimal preheat options in menus (PR#2471) 2015-07-19 16:14:59 -05:00
Scott Lahteine
eacfe132aa Change the name of servos[] and servo_t 2015-07-19 11:35:48 -07:00
Scott Lahteine
3b23ccd366 Patch servos code for move
- Have `Servo::attach` explicitly return -1 if it fails
- Check for -1 in `Servo::move` because `servoIndex` might be 0
- Make `attach` / `detach` calls conditional on `SERVO_LEVELING`
- Move `SERVO_LEVELING` define to `Conditionals.h`
2015-07-19 11:24:23 -07:00
Richard Wackerbarth
54ddc1d417 Simplify DRY RUN (PR#2358)
Elsewhere DRYRUN turns off the heating elements
and ignores constraints on them.

Here, whenever motion is entered into the planner,
if DRY RUN is set, we instantly act as if the E_AXIS
is in the desired final position.
2015-07-19 10:15:53 -05:00
Scott Lahteine
944090c19c Optimize lsDive logic 2015-07-19 10:13:40 -05:00
Scott Lahteine
417706e578 Include space for the terminating nul in lsDive 2015-07-19 10:13:39 -05:00
Scott Lahteine
f3c1a6b19c Reduce lsDive stack usage to the minimum 2015-07-19 10:13:39 -05:00
Patrick Bogen
fba4e6241b Specify print format for reporting invalid tmp_extruder (PR#2465) 2015-07-18 16:40:01 -05:00
AnHardt
d15d869267 Rename axis_is_at_home() to set_axis_is_at_home() (PR#2464)
to make clear - it's not a question but an order.
2015-07-18 10:27:21 -05:00
Scott Lahteine
f209b755a5 Move the Z probe as far as needed to trigger the switch (PR#2461) 2015-07-16 20:02:44 -05:00
Scott Lahteine
0f1df62389 Fixup comments in code_seen 2015-07-16 16:40:52 -05:00
Scott Lahteine
2945eb6650 Call code_seen only once per parameter 2015-07-16 16:40:52 -05:00
Scott Lahteine
b742af2e2a Move Y_STOP_PIN for Printrboard with SD (PR#2420) 2015-07-16 16:39:55 -05:00
Scott Lahteine
baa9199973 Define extern delta only for delta 2015-07-16 16:36:30 -05:00
Scott Lahteine
77e80ef367 Require extruders for thermal code 2015-07-16 16:36:30 -05:00
Scott Lahteine
3bde4f4855 Require temp sensor for bed thermal protection 2015-07-16 16:36:30 -05:00
Scott Lahteine
82a3ed2f9a Cleanup and dev notes in Marlin.h 2015-07-16 16:36:30 -05:00
Scott Lahteine
db23b9b184 Minor tweak to M204 code (PR#2457) 2015-07-16 16:35:13 -05:00
Scott Lahteine
81d42406b7 Move braces in homeaxis to prevent a hanging else (PR#2451) 2015-07-16 10:25:54 -05:00
Scott Lahteine
552a327df8 Fix lsDive filename stack overrun (PR#2449) 2015-07-16 10:23:56 -05:00
AnHardt
a6628f12cc Eliminate the further use of the pin-parameter 2015-07-15 20:50:58 -05:00
AnHardt
8504992e9f Remove the additional pin variable in Servo.cpp
as sugested by @c-born
inhttps://github.com/MarlinFirmware/Marlin/issues/1885#issuecomment-92618240
2015-07-15 20:50:58 -05:00
AnHardt
ed6598adf5 Corrected Bed Height vs. Bed Topology for verbosity > 3
and cleaned out some tabs.

Everything else is a rebased PR#2017 as proposed by @CptanPanic
2015-07-15 19:51:40 -05:00
brian
62302ceb9e Add calculation of difference between auto-correct bed level plane, and measured topo map. 2015-07-15 19:51:40 -05:00
Scott Lahteine
de25a48dec Remove PID examples from preconfigured configs 2015-07-15 19:13:53 -05:00
Scott Lahteine
7456710a1f Update configs formatting 2015-07-15 19:13:47 -05:00
Scott Lahteine
391386dd94 Update configs for new servo deactivation 2015-07-15 19:13:40 -05:00
AnHardt
5243d8b523 Deactivate DEACTIVATE_SERVOS_AFTER_MOVE by default 2015-07-15 17:39:43 -05:00
AnHardt
49609f6c14 Activate the new servo.move() function
by replacing the sequences (attach, write, delay, detach), and their conditions with the new function in Marlin.main.cpp
and removing the old configuration in the ABL part of Configuration.h
2015-07-15 17:39:43 -05:00
AnHardt
40b6edcad7 Introduce DEACTIVATE_SERVOS_AFTER_MOVE in Configuration.h
DEACTIVATE_SERVOS_AFTER_MOVE is ought to replace PROBE_SERVO_DEACTIVATION_DELAY.
But it will work on all servo moves, not only the probe servo moves.
2015-07-15 17:39:43 -05:00
AnHardt
2ddb2a2be9 Add Servo::move() to servo.cpp
move(pin, angel) - Sequence of attach(pin), write(angel),
                   if DEACTIVATE_SERVOS_AFTER_MOVE is defined waits SERVO_DEACTIVATION_DELAY, than detaches.

As we have jitter on the servos during moves of the steppers, and detaching them improves this behaviour,
the usual sequence to handle a servo movement is:
attach(pin)
write(angel)
delay(until the servo finished the move)
detache()

Here a function to handle the complete sequence.
2015-07-15 17:39:43 -05:00
mkile
8a01e5fb7a Update Russian translation (PR#2443)
Slightly updated translation.
2015-07-15 10:35:36 -05:00
Richard Wackerbarth
e83575537a Compiler defines USBCON for USB devices (PR#2433) 2015-07-15 10:32:11 -05:00
ayberkozgur
7268d46508 Always calculate extruder temperature PID d term (PR#2432) 2015-07-13 13:22:26 -05:00
Scott Lahteine
87a872e103 Use st_get_position_mm where possible (PR#2411) 2015-07-12 22:15:54 -05:00
Scott Lahteine
2e0da8abdc Allow N to take a negative argument (PR@2402) 2015-07-12 22:14:25 -05:00
Scott Lahteine
447dbd6fa5 Add STEPPER_RESET_PIN support 2015-07-11 16:04:11 -05:00
Scott Lahteine
a0351bdb73 Remove STEPPER_RESET_FIX option 2015-07-11 16:04:11 -05:00
Scott Lahteine
6b1b8cb2b3 Also nullify spaces before the checksum asterisk (PR#2409) 2015-07-10 09:03:07 -05:00
Scott Lahteine
8e61314323 Use RIGIDBOT_PANEL for consistency with online docs 2015-07-09 11:36:46 -05:00
Scott Lahteine
4b204da3c1 Cleanup of pins_RAMPS_13.h 2015-07-09 11:36:46 -05:00
Scott Lahteine
536f86e896 RigidBot CONTROLLERFAN_PIN in Configuration_adv.h 2015-07-09 11:36:46 -05:00
Scott Lahteine
f068e46661 RigidBoard include for pins.h 2015-07-09 11:36:46 -05:00
Scott Lahteine
9ebcae496d RIGIDBOARD / RIGIDPANEL 2015-07-09 11:36:46 -05:00
Scott Lahteine
c3c605c658 Move note about LiquidTWI2 to Configuration.h (PR#2406) 2015-07-09 05:33:17 -05:00
Scott Lahteine
4e9d658141 Prevent a hanging SERIAL_ECHO_START in M111 2015-07-07 06:59:10 -05:00
Scott Lahteine
bc0fdbe88e Use SERIAL_EOL in SERIAL_PROTOCOLLN macros 2015-07-07 06:59:10 -05:00
Scott Lahteine
d78ebbc0e9 Remove unused MSG_OK_B and MSG_OK_T 2015-07-07 06:59:10 -05:00
Scott Lahteine
6b494c1535 Use disable_all_heaters in M111 2015-07-07 06:59:10 -05:00
Scott Lahteine
15190d40df Add extra EOL after M111 2015-07-07 06:59:10 -05:00
AnHardt
0e1cf78f5c Remove code for testing if probing range is too small (PR#2390)
becaue it is over-restrictive and superseeded by the now working tests
if the probe-recktangle can be reached. See iss#2366
2015-07-07 06:58:01 -05:00
AnHardt
d421f5250d Correct the sign of zprobe_zoffset for G29 (PR#@391)
Sign flipped with #2167.
See also comments
https://github.com/MarlinFirmware/Marlin/issues/2040#issuecomment-118568355
and following.
2015-07-07 06:55:33 -05:00
Scott Lahteine
52fcc743ab Replace "target" with "destination" in M600 (PR#2374)
- Also fix a bug in `M600` where `Z_MAX_ENDSTOP_INVERTING` is being
used as the index into the `destination[AxisEnum]` array.
2015-07-04 05:55:25 -05:00
Scott Lahteine
a5033c3652 Enable LCD_PIN_RESET if it exists (PR#2375) 2015-07-04 05:53:22 -05:00
AnHardt
23c8c5348f Z-height fix V2b (PR#2351)
here the other two occurences of `Z_PROBE_OFFSET_FROM_EXTRUDER` are
replaced with `zprobe_zoffset`.
2015-07-02 20:30:40 -05:00
Todd Swindoll
a111fbbd0a z-probe offset fix (PR#2361)
verified via 1.0.2 tag that compiles by multiple people,
credit for the fix goes to paulusjacobus for the initial find and
sniffle for the correction so M851 works.
2015-07-02 20:28:07 -05:00
Scott Lahteine
42465ee444 Cleanup of comments & spacing 2015-06-28 08:20:28 -05:00
Scott Lahteine
9682ed455e Fix comment on M83, add comment to prepare_move 2015-06-28 08:20:19 -05:00
Scott Lahteine
bb44fe17cf Fix typo in buzzer.h endif (PR#2337) 2015-06-27 06:10:19 -05:00
AnHardt
36746143a1 Correct output of M48 (PR#2336)
n_samples is an uint8_t .
Got printouts like:
50 of 2  ...
2015-06-27 06:08:40 -05:00
Scott Lahteine
f6ca5a8da8 Allow "M110 N123" without a checksum 2015-06-26 18:13:54 -05:00
Scott Lahteine
aaad65ff5d Include a comment documenting M110 2015-06-26 18:13:54 -05:00
Scott Lahteine
862c72b030 Put the mandatory test of gcode_N first 2015-06-26 18:13:54 -05:00
Scott Lahteine
30976f9773 Allow M110 to handle a second N argument 2015-06-26 18:13:53 -05:00
Scott Lahteine
d135b15bb8 Init all endstop bits to 0 (PR#2332) 2015-06-26 07:10:22 -05:00
Scott Lahteine
5ccb1c9e7d Use millis for M600 audio feedback interval 2015-06-25 20:45:03 -05:00
Scott Lahteine
fb16a83b8a Cleanup M600 documentation comments 2015-06-25 20:45:03 -05:00
Scott Lahteine
97ec224d72 Replace target with destination in M600 2015-06-25 20:45:03 -05:00
Scott Lahteine
4ce9ddbb74 Check the temperature before filament change 2015-06-25 20:45:03 -05:00
Jaime van Kessel
b8b5762e55 Update Ultimaker URL 2015-06-25 09:12:44 -05:00
Jaime van Kessel
d5bfbf5a59 Added correct dutch translation for calibrate. 2015-06-25 09:12:44 -05:00
Scott Lahteine
149c474e55 Updated Russian language (PR#2325)
Gleaned from
https://github.com/MarlinFirmware/Marlin/commit/4ac14a7e5fa8e6e395436664
8976eafd1ae220ae
2015-06-22 23:07:19 -04:00
AnHardt
722829b058 Move buzzing code to buzzr.h & buzzer.cpp (PR#2307)
at least the lcd independent part from Marlin_main.cpp.
2015-06-22 22:31:48 -04:00
AnHardt
c461975140 Rename and repair MELZI_1284 (PR#2301)
to MELZI_MAKR3D.

Fix for #2288
As the normal MELZI also can have a 1284.
2015-06-22 22:30:07 -04:00
schlotzz
1e9cf905c7 Enable ZigZag AutoBedLeveling on Deltas (PR#2273)
ZigZag has been disabled by fault due to do_topography_map
2015-06-15 20:26:25 -05:00
Scott Lahteine
ec93383ec8 Add SanityCheck for bed probe position settings (PR#2282) 2015-06-15 20:22:44 -05:00
Scott Lahteine
dc40a5f6e0 Patch up more outdated config lines 2015-06-15 20:20:32 -05:00
Scott Lahteine
98c9111a7d Update delta configs with latest settings 2015-06-15 20:20:32 -05:00
Scott Lahteine
e6baf8afd9 Fix up allen key settings in delta configs 2015-06-15 20:20:31 -05:00
Scott Lahteine
3b293fc5d1 Move Delta settings lower in delta files 2015-06-15 20:20:31 -05:00
Scott Lahteine
df21857583 Move extruder offset settings next to extruders setting 2015-06-15 20:20:31 -05:00
Scott Lahteine
2dd1859247 Cleanup spaces and comments in configs and conditionals 2015-06-15 20:20:31 -05:00
Scott Lahteine
a274769f4f Clean up spacing and comments
Also clean up some trailing spaces in a few other sources
2015-06-15 20:20:31 -05:00
Scott Lahteine
d3bce05d54 Fix up spacing for filament sensor values 2015-06-15 20:20:31 -05:00
Scott Lahteine
b4b10a57fe Fix configurator section directives and values lists 2015-06-15 20:20:31 -05:00
Scott Lahteine
bba14dcbe6 Move Z Safe Homing point to the middle of the movement range 2015-06-15 20:20:31 -05:00
Scott Lahteine
318318b02f Add pins_RAMPS_13_EFB.h to reduce redundancy 2015-06-15 20:17:09 -05:00
Scott Lahteine
346c8b339b Remove a test from pins_RAMPS_13.h
- Add 3 new lines to `pins.h` to remove 2 redundant tests in
`pins_RAMPS_13.h`
2015-06-15 20:15:38 -05:00
AnHardt
b93cddfcc9 Add lost MKS_BASE to pins.h (PR#2297) 2015-06-15 10:23:46 -05:00
AnHardt
6ab7b560af Rework buzzing (PR#2296)
by:
Moving HAS_LCD_BUZZ macro to Coditionals.h
Renaming HAS_LCD_BUZZ to HAS_BUZZER to make clear is has nothing to do with the lcd.
Removing the ULTRALCD condition.

Moving declaration of lcd_buzz() out of the ULTRA_LCD block in ultralcd.h
Moving definition of lcd_buzz() out of the ULTIPANEL block in ultralcd.cpp
Renaming lcd_buzz() to buzz() to make clear is has nothing to do with the lcd.

All buzzing code is now only dependent on the existence of a BEEPER-pin or the definition of a LCD_USE_I2C_BUZZER.

To do: Check the conditions for the BEEPER-pin in all pin-files.
2015-06-15 06:13:26 -05:00
Scott Lahteine
29122db2fa Fix ULTRA_LCD spelling in HAS_LCD_BUZZ 2015-06-15 06:12:34 -05:00
Scott Lahteine
1d94d098bf Formatting tweaks as part of fixing issue 1497 2015-06-14 19:57:27 -05:00
Scott Lahteine
e602c28ad9 Set auto fan pins to OUTPUT during init
Fixes the problem of these pins being left in INPUT state, as described
in #1497
2015-06-14 19:57:27 -05:00
Scott Lahteine
90f858aa85 Use translated strings for axis movement (PR#2280)
Suggest we use the translated strings here. They use (except for
German) the phrasing “Move X” instead of just the axis letter, but they
should fit the available space. The “Extruder” string would be the
same, except it will be translated.
2015-06-14 08:16:00 -05:00
Scott Lahteine
e2a4a83586 Don't re-apply Z_RAISE_BETWEEN_PROBINGS in probe_pt (PR #2281) 2015-06-12 22:39:35 -05:00
Scott Lahteine
6b1b3adaf0 Consistent punctuation in SanityCheck errors (PR#2283) 2015-06-12 09:31:02 -05:00
MagoKimbra
eb81982fcd Fix error next command in autotune (PR#2274)
Now send only temperature for T or B, but not send OK.
Host interprets the line to show the right temperature, but not in
response to M105 then stop and send commands until it ends the autotune.
2015-06-12 07:10:38 -05:00
AnHardt
55b23c896a Optimise out_of_range_error() (PR#2265)
by avoiding the strncopy()
2015-06-12 02:20:40 -05:00
filipmu
b0860adab6 Fix volumetric multiplier display for filament sensor (PR#2264)
The volumetric multiplier display needs to be multiplied by 100 in order to make it an integer for display purposes.
2015-06-12 02:19:27 -05:00
AnHardt
45642b7fe8 Respect DISABLE_AXIS settings (PR#2216)
when DEFAULT_STEPPER_DEACTIVE_TIME is over
instead of simply turn off all.
2015-06-11 11:35:05 -05:00
wurstnase
c85a486445 make the dual z-endstop optional (PR#2277)
it's disabled by default
2015-06-10 15:45:59 -05:00
Scott Lahteine
962b107341 Prevent current_command_args from bypassing nul (PR#2270) 2015-06-09 16:07:10 -05:00
Richard Wackerbarth
06ae832276 Deprecate Support for Arduino IDE < 1.0.5
Note that newer versions of the IDE can still
be made to support compilation for the older boards.
2015-06-08 17:15:28 -05:00
Scott Lahteine
ff6081be3a Parse N[0-9]+[ ]* differently (PR #2263)
More general solution to skip N[0-9]+[ ]* in the parser as in #2218
2015-06-08 17:06:49 -05:00
Scott Lahteine
aad121864e Include "Z" in M851 report 2015-06-08 05:09:27 -05:00
Scott Lahteine
96a3fba8ac Reverse the sign of zprobe_zoffset
- When editing on the LCD, minus now means below the nozzle
- Stores the opposite sign in EEPROM, so bumped to “V20”
2015-06-08 05:09:27 -05:00
fmalpartida
f92907183c Updated SAV MkI pin header. 2015-06-08 05:07:11 -05:00
Richard Wackerbarth
58941e543e ELB_FULL_GRAPHIC_CONTROLLER_SDCARDDETECTINVERTED removed
#defining something just to define something else doesn’t
make sense

If you want SDCARDDETECTINVERTED, just define it yourself.

If the previous code was intended to define, undefined and then again define the term, that code is improper.
2015-06-06 21:44:59 -05:00
CONSULitAS
788eb6e647 planner.cpp: remove tab
planner.cpp: single evil and hidden tab removed ♻️ 😏
2015-06-06 20:13:56 -05:00
CONSULitAS
3a5963c0e7 Configuration_adv.h: Add FAN_MIN_PWM for slow fan stopping issue …
* all Configuration_adv.h: Add #define FAN_MIN_PWM for slow fan stopping
issue
* for K8200: uncommented with tested (and working) values
2015-06-06 20:13:56 -05:00
CONSULitAS
e55e65d1e4 planner.cpp: Add FAN_MIN_PWM for slow fan stopping issue …
@CONSULitAS

planner.cpp: Add FAN_MIN_PWM for slow fan stopping issue (V2.1 with
macro and linear scaling)

@thinkyhead thanks for idea on linear scaling
2015-06-06 20:13:56 -05:00
paclema
8d295547be * Auto filament change on CHANGEFILAMENT feature. Now you can activate this option that extrude filament until you press the button. 2015-06-06 19:45:45 -05:00
atfield90
6d0e91328d Renamed Board_megatronics_1 to Board_minitronics 2015-06-06 18:59:04 -05:00
atfield90
c4a2e5ac23 Renamed Pins_megatronics_1 to Pins_minitronics 2015-06-06 18:59:04 -05:00
atfield90
2076906aaa Renamed Pins_megatronics_1 to Pins_minitronics 2015-06-06 18:59:04 -05:00
tonokip
10733a2bb0 added minirambo pin definitions. V2 2015-06-06 18:37:58 -05:00
Richard Wackerbarth
303d47228e Define Probe Path in new format 2015-06-06 17:48:27 -05:00
Richard Wackerbarth
ad09d6a60f 3 Step Allen Key Probe 2015-06-06 17:48:27 -05:00
Richard Wackerbarth
8359cdf01d Check compatibility for Teensy-based processor
The instruction say to set a #define in fastio.h
However, that value is not included before this test.
2015-06-06 17:24:34 -05:00
Ed Boston
08968c29bb Adding ELB_FULL_GRAPHIC_CONTROLLER_SDCARDDETECTINVERTED to Examples 2015-06-06 16:40:32 -05:00
Ed Boston
fed18bcc20 Removed SDSLOW for ELB_FULL_GRAPHIC_CONTROLLER
Hardware changes has removed the need for this option.
2015-06-06 16:40:32 -05:00
Ed Boston
b94a0e1501 Added ELB_FULL_GRAPHIC_CONTROLLER_SDCARDDETECTINVERTED
The new define allows the sd card detect to be inverted or not from
Configuration.h
2015-06-06 16:40:31 -05:00
Ed Boston
bc205c76a3 SDCARDDETECTINVERTED problems
Fixed an error where SDCARDDETECTINVERTED was being defined/undefined
improperly
2015-06-06 16:40:31 -05:00
AnHardt
e400fce271 Merge pull request #2221 from MagoKimbra/Dryrun
Insert Debug DRYRUN Repetier Host compatible
2015-06-03 12:30:48 +02:00
AnHardt
163a9ff58e Merge pull request #2230 from AnHardt/psm
Fix thermal protection state machine target temp. V2
2015-06-03 09:46:53 +02:00
AnHardt
c3fe6e61ae Merge pull request #2229 from AnHardt/position-out-of-range
Fix out_of_range_error()
2015-06-03 09:46:22 +02:00
MagoKimbra
4db8d2def4 Moved MSG_DEBUG in language.h 2015-06-03 08:18:27 +02:00
AnHardt
b7e9ba7591 Back to 1.0.3 dev - for now 2015-06-03 00:47:11 +02:00
AnHardt
d1f4471000 Merge pull request #2146 from Wackerbarth/Versioning
Versioning
2015-06-02 18:31:21 +02:00
AnHardt
b1404a0743 fix thermal protection state machine target temp. V2
If the target temperature is changed then it would always stay in the reset state.
Thanks to @tonokip.

Replaces #2119
2015-06-02 12:26:21 +02:00
AnHardt
17b0ec84ed Fix out_of_range_error()
For sprintf_P() the first parameter has to be a `char*` not `const char*`.
2015-06-02 11:50:32 +02:00
AnHardt
35af5ef23e Merge pull request #2225 from Wurstnase/naming
consistency name for multiplier
2015-06-02 10:18:22 +02:00
wurstnase
e7e964432b consistency name for multiplier
replace extruder_multiply with extruder_multiplier
like feedrate_multiplier or volumetric_multiplier
2015-06-01 22:33:22 +02:00
AnHardt
d4c6fc5d0a Merge pull request #2223 from AnHardt/dualz-semicolon
Add a semicolon to make Z_DUAL_STEPPER_DRIVERS compile again.
2015-06-01 20:15:55 +02:00
AnHardt
0d9d21d15f Add a semicolon to make Z_DUAL_STEPPER_DRIVERS compile again. 2015-06-01 19:51:43 +02:00
MagoKimbra
76306f9073 Insert Debug DRYRUN Repetier Host compatible 2015-06-01 18:34:45 +02:00
MagoKimbra
881146bc22 Fix problem Width Cura 2015-06-01 17:25:32 +02:00
fmalpartida
11e3f3375d Merge commit '764e61708b8e73410c7819d59c4970d7089ca6f5' into bugFixing
Updated LCD wiki location.
2015-05-31 21:20:26 +02:00
Alexey Shvetsov
a8670b66a7 Update ru translation
Signed-off-by: Alexey Shvetsov <alexxy@gentoo.org>
2015-05-31 20:09:10 +03:00
fmalpartida
93da52d011 Added support for OLED SSD1306 I2C based LCDs. 2015-05-31 18:53:29 +02:00
Wurstnase
9c09967803 Merge pull request #2149 from Wurstnase/enstop_bits
faster compare
2015-05-31 16:02:55 +03:00
wurstnase
0f3f7d6835 clean up double endstops 2015-05-31 14:06:13 +02:00
AnHardt
9d2a980bcf Merge pull request #2170 from thinkyhead/beep_M600_elsewise
Slight size reduction by adding idle()
2015-05-30 12:42:32 +02:00
AnHardt
2728dc0606 Merge pull request #2194 from thinkyhead/reduce_strings
Redo "invalid extruder" to save 304 bytes
2015-05-30 11:05:08 +02:00
Scott Lahteine
be5236e839 Reduce setTargetedHotend by removing the switch 2015-05-29 18:03:58 -07:00
Scott Lahteine
06f401e7e5 Redo "invalid extruder" to save 264 bytes
- Use `setTargetedHotend` in `M200`, as with other commands that use
`T` for the extruder
- Synthesize the "invalid extruder" message, obviating several long
strings
2015-05-28 22:25:28 -07:00
Scott Lahteine
1a882bcc2e Merge pull request #2193 from thinkyhead/ignore_unrecognized_commands
Ignore unknown commands if they start with G, M, or T
2015-05-28 22:03:48 -07:00
Scott Lahteine
a672872717 Merge pull request #2187 from AnHardt/MAX6675M105
Print active extruder with M105 for MAX6675
2015-05-28 18:12:48 -07:00
Scott Lahteine
9beed830eb Drop commented code_is_good lines 2015-05-28 17:53:47 -07:00
Scott Lahteine
068d4a1eb2 Ignore unknown commands if they start with G, M, or T 2015-05-28 17:44:09 -07:00
Scott Lahteine
5824f613ff Merge pull request #2185 from jothan/bed_integral
Separate the maximum integral power for the bed from PID_INTEGRAL_DRI…
2015-05-28 16:32:02 -07:00
Scott Lahteine
c5c9d12630 Merge pull request #2183 from AnHardt/displayinit
Initialize the display earlier
2015-05-28 16:29:18 -07:00
Scott Lahteine
ef4becc413 Merge pull request #2188 from AnHardt/FtoN
Replace MSG_F? with MSG_N?
2015-05-28 16:18:50 -07:00
Scott Lahteine
0564625757 Update M33 for new gcode parser 2015-05-28 14:17:39 -07:00
AnHardt
f18f689c01 Replace MSG_F? with MSG_N?
To avoid double definitions.
I prefer to read N for Number not for Nozzle.
2015-05-28 20:30:23 +02:00
AnHardt
af7e3f5076 Print active extruder with M105 for MAX6675
Was omitted when T0 is a MAX6675.
2015-05-28 19:03:16 +02:00
Jonathan Bastien-Filiatrault
d46d9d998e Add maximum bed integral term in example configurations. 2015-05-28 12:51:37 -04:00
Jonathan Bastien-Filiatrault
e86f2342c0 Separate the maximum integral power for the bed from PID_INTEGRAL_DRIVE_MAX / PID_MAX.
My PID_INTEGRAL_DRIVE_MAX was at 96, which was insufficient for my bed
to reach its intended temperature. The head requires a low maximum power since
I run on 24 volts and it has a somewhat low thermal mass.
2015-05-28 11:48:04 -04:00
AnHardt
f0523b5816 Initialize the display earlier
to have it ready to display errors during (temperature)-setup.
2015-05-28 16:08:17 +02:00
Scott Lahteine
790c697c19 Fix DEGREES macro 2015-05-28 00:19:48 -07:00
Scott Lahteine
76b4678f99 Merge pull request #2171 from thinkyhead/gcode_110_is_good
M110 is a known command
2015-05-26 21:17:58 -07:00
Scott Lahteine
03d5709b09 M110 is a known command
- The command parser now displays “unknown command” in more cases.
Known commands must be added to the `switch` inside `process_commands`
to suppress the error.
2015-05-26 20:31:18 -07:00
Scott Lahteine
d76a01194d Slight size reduction by adding idle() 2015-05-26 20:08:21 -07:00
Richard Wackerbarth
2deb5a8ac5 Temporary Hack
REVERT THIS CHANGE

In proper use, we want to force the vendor to update this file to reflect distribution parameters

However, until most users have converted to automatic versioning,
we “grant them a pass”
2015-05-25 15:54:08 -05:00
Richard Wackerbarth
b5743d6927 Use SOURCE_CODE_URL rather than FIRMWARE_URL 2015-05-25 15:53:34 -05:00
Richard Wackerbarth
5ea139fd79 Revised Versioning mechanism 2015-05-25 15:53:14 -05:00
AnHardt
da246f5cb1 Activate BED_MINTEMP error.
And call _temp_error() directly for ERR_MAXTEMP_BED to avoid the only one time use of bed_max_temp_error().

Includes #2156.
2015-05-25 13:23:19 +02:00
AnHardt
959da98d8e Call kill() only once when triggered by a temperature error
to avoid stack overflow when called from interrupt.

Some clean up for calls of disable_all_heaters().
'disable_all_heaters()' is called in kill() and again when 'killed' is already set inside _temp_error().
2015-05-25 12:44:03 +02:00
Scott Lahteine
68f6f149d0 Reduce code size with out_of_range_error function
- Affects code size when automatic bed leveling is enabled
2015-05-24 20:18:02 -07:00
wurstnase
94120740d8 faster compare
!(~(ab)&0x3) and ab == 0x3 are equal
2015-05-23 07:55:15 +02:00
Scott Lahteine
c9141e604a Merge pull request #2145 from thinkyhead/gcode_folding
Indentation in process_commands
2015-05-22 18:47:37 -07:00
Scott Lahteine
b55f8718c3 Indent G90/G91, G92 2015-05-22 17:34:08 -07:00
Scott Lahteine
b0d520b109 Indent G30, G31/G32 2015-05-22 17:33:17 -07:00
Scott Lahteine
ffe27a6225 Indent G29 2015-05-22 17:32:46 -07:00
Scott Lahteine
86083badc2 Indent G4, G10/G11, G28 2015-05-22 17:32:27 -07:00
Scott Lahteine
47d7a9cb5e Indent G2/G3 2015-05-22 17:31:38 -07:00
Scott Lahteine
350f239d84 Indent G0/G1 2015-05-22 17:31:24 -07:00
Scott Lahteine
672b0c1fd3 Cleanup pins in RAMPS_13_EFB boards 2015-05-22 16:20:54 -07:00
Scott Lahteine
15a2351675 No need for +1 on initial seen_pointer 2015-05-22 15:31:30 -07:00
Scott Lahteine
550dd87b2a Set seen_pointer before calling code_value 2015-05-22 15:11:48 -07:00
Scott Lahteine
38cc0b93c6 Merge pull request #1874 from AnHardt/Bulgarian
Introduction of Bulgarian - language_bg.h
2015-05-22 13:59:50 -07:00
Scott Lahteine
04a1622172 Merge pull request #2127 from Wackerbarth/Kossel_Pro
Kossel Pro
2015-05-21 18:43:26 -07:00
Scott Lahteine
81c2ca3e10 Merge pull request #2131 from thinkyhead/bq_is_ramps_13_efb
Witbox and Hephestos are RAMPS EFB
2015-05-21 18:39:02 -07:00
Scott Lahteine
f919a2fed1 Merge pull request #2134 from AnHardt/preheat-all
Shift call of start_watching_heater() into setTargetHotend()
2015-05-21 18:36:28 -07:00
Scott Lahteine
063881b5bd Fix a couple of doubled semicolons 2015-05-21 18:15:29 -07:00
AnHardt
94dff5b36a Merge pull request #2137 from thinkyhead/tweak_swh
Move millis call in start_watching_heater
2015-05-22 02:02:07 +02:00
Scott Lahteine
70d2f48d4e Merge pull request #2136 from thinkyhead/M303_suppress_error
Suppress the line mismatch error after M303
2015-05-21 16:46:30 -07:00
AnHardt
0c0ace2a04 Remove start_watching_heater() fom M104 and M109 2015-05-22 01:44:50 +02:00
Scott Lahteine
00716d0ca0 Small start_watching_heater adjustment 2015-05-21 16:44:49 -07:00
Scott Lahteine
834747deb7 Merge pull request #2135 from Wurstnase/new_endstop_bits
new endstop bits
2015-05-21 16:35:54 -07:00
Scott Lahteine
bde9c70d42 Suppress the line mismatch error after M303 2015-05-21 16:27:22 -07:00
Scott Lahteine
50bd7493cc Merge pull request #2108 from thinkyhead/m33_long_filename_host_support
M33 LONG_FILENAME_HOST_SUPPORT
2015-05-21 16:22:47 -07:00
Scott Lahteine
4d11b29959 Merge pull request #2113 from thinkyhead/command_sanitizer
Command sanitizer
2015-05-21 16:21:58 -07:00
wurstnase
ff98b8632b new endstop bits 2015-05-21 23:16:43 +02:00
AnHardt
9b0fa9c309 Changed dependency of start_watching_heater() in setTargetHotend() to THERMAL_PROTECTION_HOTENDS 2015-05-21 21:07:37 +02:00
AnHardt
bc0764894a Shift call of start_watching_heater() into setTargetHotend()
to warrant watching is set or reset.

Make setTargetBed() in _lcd_preheat() dependant of TEMP_SENSOR_BED.
Use disable_all_heaters() in lcd_cooldown() and abort_on_endstop_hit.
2015-05-21 20:36:11 +02:00
Richard Wackerbarth
b878bc5620 Introducing the Kossel Pro Build Configuration 2015-05-21 11:47:34 -05:00
Richard Wackerbarth
1d8f61ca8a AT90USB is defined in pins.h 2015-05-21 11:46:54 -05:00
Richard Wackerbarth
735bf2d35f Describe Custom M Code 2015-05-21 08:06:33 -05:00
Scott Lahteine
f39658c822 M120 and M121 are reversed 2015-05-21 00:17:44 -07:00
Scott Lahteine
6eb4f90ce7 Also synchronize configurator copies of configs 2015-05-20 21:34:00 -07:00
Scott Lahteine
9d1961ebe3 Witbox and Hephestos are just RAMPS_13_EFB 2015-05-20 21:33:23 -07:00
AnHardt
4422365a53 Merge branch 'Development' of https://github.com/MarlinFirmware/Marlin into _temp_error 2015-05-20 23:34:39 +02:00
AnHardt
4113762062 Merge pull request #2130 from AnHardt/kill2
Add a string parameter to kill()
2015-05-20 23:32:51 +02:00
AnHardt
89d2ee6f13 Make output on display dependant of ULTRA_LCD 2015-05-20 22:03:16 +02:00
AnHardt
120d4c7a8c Merge remote-tracking branch 'origin/kill2' into _temp_error 2015-05-20 21:25:32 +02:00
AnHardt
cb6e82dc60 Change from kill() to kill(const char *)
in temperature.cpp
2015-05-20 21:22:48 +02:00
AnHardt
9d13942278 Use new kill() with parameter. 2015-05-20 21:18:52 +02:00
AnHardt
6398c5e28d Merge remote-tracking branch 'origin/kill2' into _temp_error 2015-05-20 21:08:19 +02:00
AnHardt
f4a93ed997 Add a string parameter to kill()
Makes the output on the LCD adjustable.
2015-05-20 20:53:48 +02:00
AnHardt
2990c6c45f Use new kill_() for _temp_error()
instead of stop(). We really want to require a reset and no chance to set a new temperature.
2015-05-20 14:03:14 +02:00
AnHardt
9b8c6ed254 Merge pull request #2120 from chris-bo/dogm_config
move dogm font selection to configuration_adv.h
2015-05-20 10:11:34 +02:00
AnHardt
06513565e9 Merge pull request #2105 from eboston/Development
Add  ELB_FULL_GRAPHIC_CONTROLLER with ADAFRUIT_ST7565 display.
2015-05-20 09:56:21 +02:00
Ed Boston
082ed3beed Propagate Configuration.h changes
Updated all the example Configuration.h files for the new display type.
2015-05-19 14:04:57 -07:00
Ed Boston
152b681bb5 Added link to controller github
Added the link to the github information about the
ELB_FULL_GRAPHIC_CONTROLLER
2015-05-19 04:14:55 -07:00
AnHardt
995b84944b Merge pull request #1982 from CONSULitAS/Development_Update_language.h
language.h: update documentation / URL für K8200
2015-05-19 12:13:35 +02:00
Scott Lahteine
7bc5fd8193 Merge pull request #2123 from AnHardt/Duemilanove
Remove Duemilanove
2015-05-18 20:36:05 -07:00
Scott Lahteine
94de1e0d93 Merge pull request #2116 from AnHardt/wording
transpire -> expire
2015-05-18 20:34:46 -07:00
AnHardt
4d4fa3607b Remove Duemilanove
No way to fit Marlin into 32K.
2015-05-19 02:46:37 +02:00
AnHardt
e353d27430 Merge branch 'Development' of https://github.com/MarlinFirmware/Marlin into Bulgarian 2015-05-18 23:56:53 +02:00
Ed Boston
ca8d1756d5 Define fixes
Fixed a couple defines that were not changed or commented out.
2015-05-18 14:23:31 -07:00
CONSULitAS
b96b28b7cc language.h: update documentation for LANGUAGE_INCLUDE
language.h: update documentation for LANGUAGE_INCLUDE

@thinkyhead What do you think? I think there should be a warning like
this.
2015-05-18 23:11:26 +02:00
Christian Bohn
258bcdefe0 move dogm font selection to configuration_adv.h 2015-05-18 22:54:53 +02:00
AnHardt
7750180c93 transpire -> expire
Minor wording correction.
2015-05-18 21:48:10 +02:00
AnHardt
70163dafb9 Use _temp_error() for all errors thrown by different mechanisms
Now ending in an endless loop.
Tidy up the output format.
We now get:
ERRORTEXT ", system stopped! Heater_ID: " HEATERID

Where ERRORTEXT can be:
"Heating failed"
"Thermal Runaway"
"MAXTEMP triggered"
"MINTEMP triggered"
and soon
"Thermal Jump"

HEATERID can be
0, 1, 2 ,3 , "bed"

This messages are always followed by the common:
"Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)"
2015-05-18 20:26:25 +02:00
Scott Lahteine
a0f362c735 Simplify & optimize with current_command_args 2015-05-18 07:08:04 -07:00
Scott Lahteine
adc8fcb77f More parser comments, optimize code_seen, save with goto 2015-05-18 07:08:04 -07:00
Scott Lahteine
c6d8dd19d9 use fetched value 2015-05-18 07:08:04 -07:00
Scott Lahteine
1116e13f5a Further optimization of command parser 2015-05-18 07:08:03 -07:00
Scott Lahteine
3a4c3ab76e Pre-sanitize the command before handling
- Use a global pointer for the current sanitized command
- Pre-sanitize the current command to bypass `N` and nullify `*`,
removing the need for handlers to bypass, ignore, or nullify these
parts, and reducing overhead for `code_seen`, etc.
- Pre-skip leading whitespace.
- Only look for G, M, T codes at the start of the command.
- Verify that G, M, T codes are followed by command codes.
2015-05-18 07:06:51 -07:00
Ed Boston
a83bf18ee1 More functional seperation
Moved SDCARDDETECTINVERTED and SDSLOW to Conditionals.h.
Added U8GLIB_LM6059_AF to define display specific actions.
Added reminder to compile in u8glib
2015-05-18 05:37:46 -07:00
AnHardt
97ca1b3f4d Name magic value 20 to MAX_OVERSHOOT_PID_AUTOTUNE
to make it better findable.
2015-05-18 14:15:29 +02:00
Scott Lahteine
0f2c9bacfd M33 LONG_FILENAME_HOST_SUPPORT 2015-05-17 17:36:32 -07:00
Scott Lahteine
3feaef6526 Have G92 set the nozzle position on Delta and SCARA 2015-05-17 17:08:05 -07:00
Ed Boston
047e688e93 Changed ADAFRUIT_ST7565 to ELB_FULL_GRAPHIC_CONTROLLER
Rename of define to avoid confusion between the controller and the
display which had similar names.
2015-05-17 15:23:17 -07:00
Ed Boston
1999ac415c Formatting Changes
Fixes for some code formatting changes and commenting out the
ADAFRUIT_ST7565 define that was left defined.
2015-05-17 13:39:24 -07:00
Ed Boston
41f8cdb3a6 ADAFRUIT_ST7565
Added support for new display type
2015-05-17 12:47:41 -07:00
wurstnase
21ff773832 rework out_bits 2015-05-17 14:33:09 +02:00
Scott Lahteine
6c27eaf864 Merge pull request #2101 from thinkyhead/code_style
Code style and a dangling "else"
2015-05-17 03:39:08 -07:00
Scott Lahteine
d580a0d186 Use "+=" in plane rotation 2015-05-17 01:51:14 -07:00
Scott Lahteine
2f3a410cb0 Fix a potential hanging "else" bug 2015-05-17 01:50:30 -07:00
Scott Lahteine
b83e3f0905 Combine "Bed X: " strings 2015-05-17 01:49:52 -07:00
Scott Lahteine
7dfb8becdb Adjust some names and types in Marlin_main.cpp 2015-05-17 01:48:51 -07:00
Scott Lahteine
c966aa26ff Comments in Marlin_main.cpp 2015-05-17 01:47:53 -07:00
Scott Lahteine
c54a2ea042 Adjust spacing in Marlin_main.cpp and stepper.* 2015-05-17 01:47:02 -07:00
Scott Lahteine
072625ccad Update headings in Marlin_main.cpp and stepper.cpp 2015-05-17 01:44:53 -07:00
Scott Lahteine
16032f149f Rename to codenum as a consistency 2015-05-16 23:17:35 -07:00
Scott Lahteine
273a4a253f Merge pull request #2096 from thinkyhead/cherry_picking3
Hide M117 with no LCD
2015-05-16 21:10:28 -07:00
Scott Lahteine
64825a3d1e Merge pull request #2095 from thinkyhead/cherry_picking2
Add gcode_line_error to reduce code size
2015-05-16 21:09:15 -07:00
Scott Lahteine
ca79282eaf Hide M117 with no LCD 2015-05-16 20:59:04 -07:00
Scott Lahteine
ce218cafdb Add gcode_line_error to reduce code size 2015-05-16 20:54:58 -07:00
Scott Lahteine
46d59784ad Rename preocess_command to process_next_command 2015-05-16 20:47:40 -07:00
Scott Lahteine
513077c317 Minor change to fan kick 2015-05-16 19:42:28 -07:00
Scott Lahteine
76438195f0 NO_TIMEOUTS and ADVANCED_OK off by default 2015-05-16 02:47:20 -07:00
Scott Lahteine
d2563804c8 Add LF to file errors 2015-05-15 04:37:22 -07:00
Scott Lahteine
e114662cfa Adjust SdBaseFile spacing 2015-05-15 03:23:49 -07:00
Scott Lahteine
98e91f5253 Allow lsDive to recurse with minimal stack usage 2015-05-15 03:19:07 -07:00
Scott Lahteine
19166a92e4 Merge pull request #2057 from Wurstnase/serial_wait
add plan buffer remaining for 'P' and block buffer remaining 'B'
2015-05-14 04:57:08 -07:00
Scott Lahteine
95f5a68006 Merge pull request #2074 from thinkyhead/lcd_xyz_unknown
Display unknown XYZ on the LCD as "---"
2015-05-14 04:56:38 -07:00
Scott Lahteine
e97fcafd0e Merge pull request #2076 from thinkyhead/mendel_inverting
Use MSG_OK in M105
2015-05-14 04:54:11 -07:00
Scott Lahteine
0f6cd3640b Drop extraneous ok_to_send 2015-05-14 04:38:09 -07:00
Scott Lahteine
0ce355d9e7 Use MSG_OK in M105 2015-05-14 03:33:38 -07:00
Scott Lahteine
a366e57385 Merge pull request #2075 from thinkyhead/mendel_inverting
Use Mendel default for INVERT_Y_DIR
2015-05-14 03:29:24 -07:00
Scott Lahteine
7b3acfbb6f Merge pull request #2072 from thinkyhead/better_arc_code
Consolidate arc code, remove motion_control.*
2015-05-14 00:27:22 -07:00
Scott Lahteine
78beef2d73 Use Mendel default for INVERT_Y_DIR 2015-05-14 00:25:47 -07:00
Scott Lahteine
1a4a09c26f Display unknown XYZ on the LCD as "---"
- Also show 2 digits past decimal for Z on DOGM
2015-05-13 22:45:58 -07:00
Scott Lahteine
68ce419147 Note on segment size 2015-05-13 19:11:36 -07:00
Scott Lahteine
8b92249f18 Bring arc_offset into auto scope 2015-05-13 19:00:46 -07:00
Scott Lahteine
80807b2d71 Consolidate arc code, remove motion_control.* 2015-05-13 18:52:41 -07:00
Scott Lahteine
f65833931d Formatting tweaks 2015-05-13 02:02:19 -07:00
Scott Lahteine
fcfd99c1ae Add comments to lcd_control_temperature_menu 2015-05-12 18:46:16 -07:00
Scott Lahteine
d693e0f378 Use WATCH_TEMP_INCREASE + TEMP_HYSTERESIS + 1 as difference limit 2015-05-12 18:30:38 -07:00
Scott Lahteine
6697a8f375 Watch the heater a little longer 2015-05-12 18:22:47 -07:00
Scott Lahteine
5693a6e3c9 Fix heating error message 2015-05-12 18:17:13 -07:00
Scott Lahteine
747fd5801c Merge pull request #2055 from thinkyhead/thermal_unified
Combine thermal runaway and watch-period
2015-05-12 08:04:29 -07:00
Scott Lahteine
6e5572228d Merge pull request #2064 from thinkyhead/wait_before_g28
Split up prepare_move by type
2015-05-12 07:53:11 -07:00
Scott Lahteine
27ad381e25 Allow fractional seconds in G4 and M0 2015-05-12 07:52:08 -07:00
Scott Lahteine
5146694452 Merge pull request #1884 from shaggythesheep/feature_new_board_ramps_cnc_controller
Feature: Add RAMPS CNC Controller Board
2015-05-12 04:31:49 -07:00
Scott Lahteine
b2bd9aae7c SCARA_SEGMENTS_PER_SECOND 2015-05-12 04:18:15 -07:00
Scott Lahteine
bd20bd5444 Merge pull request #2063 from chris-bo/autobed_sled
improve sled handling
2015-05-12 03:29:21 -07:00
Scott Lahteine
9e95ceb3fc Split up prepare_move by type
- For better encapsulation add inlines for each prepare_move type
- Move controllerFan vars inside the function as statics
- Some formatting cleanup
- Rename `ClearToSend` as `ok_to_send`
2015-05-12 02:08:20 -07:00
Scott Lahteine
9ba8cf5fe3 Merge pull request #2061 from thinkyhead/wait_before_g28
Always do st_synchronize() before G28
2015-05-12 02:05:30 -07:00
Scott Lahteine
873f7d6f2a Check that configs are up-to-date 2015-05-12 01:33:51 -07:00
Christian Bohn
f48599f172 add pin definition to some motherboards 2015-05-12 10:02:23 +02:00
Scott Lahteine
b5200e184c Remove extra setup_for_endstop_move 2015-05-12 01:01:53 -07:00
Scott Lahteine
8d814de558 Return void in prevent_dangerous_extrude 2015-05-12 00:55:00 -07:00