Commit graph

991 commits

Author SHA1 Message Date
Scott Lahteine
81d42406b7 Move braces in homeaxis to prevent a hanging else (PR#2451) 2015-07-16 10:25:54 -05:00
AnHardt
ed6598adf5 Corrected Bed Height vs. Bed Topology for verbosity > 3
and cleaned out some tabs.

Everything else is a rebased PR#2017 as proposed by @CptanPanic
2015-07-15 19:51:40 -05:00
brian
62302ceb9e Add calculation of difference between auto-correct bed level plane, and measured topo map. 2015-07-15 19:51:40 -05:00
AnHardt
49609f6c14 Activate the new servo.move() function
by replacing the sequences (attach, write, delay, detach), and their conditions with the new function in Marlin.main.cpp
and removing the old configuration in the ABL part of Configuration.h
2015-07-15 17:39:43 -05:00
Scott Lahteine
87a872e103 Use st_get_position_mm where possible (PR#2411) 2015-07-12 22:15:54 -05:00
Scott Lahteine
2e0da8abdc Allow N to take a negative argument (PR@2402) 2015-07-12 22:14:25 -05:00
Scott Lahteine
447dbd6fa5 Add STEPPER_RESET_PIN support 2015-07-11 16:04:11 -05:00
Scott Lahteine
6b1b8cb2b3 Also nullify spaces before the checksum asterisk (PR#2409) 2015-07-10 09:03:07 -05:00
Scott Lahteine
4e9d658141 Prevent a hanging SERIAL_ECHO_START in M111 2015-07-07 06:59:10 -05:00
Scott Lahteine
6b494c1535 Use disable_all_heaters in M111 2015-07-07 06:59:10 -05:00
Scott Lahteine
15190d40df Add extra EOL after M111 2015-07-07 06:59:10 -05:00
AnHardt
d421f5250d Correct the sign of zprobe_zoffset for G29 (PR#@391)
Sign flipped with #2167.
See also comments
https://github.com/MarlinFirmware/Marlin/issues/2040#issuecomment-118568355
and following.
2015-07-07 06:55:33 -05:00
Scott Lahteine
52fcc743ab Replace "target" with "destination" in M600 (PR#2374)
- Also fix a bug in `M600` where `Z_MAX_ENDSTOP_INVERTING` is being
used as the index into the `destination[AxisEnum]` array.
2015-07-04 05:55:25 -05:00
AnHardt
23c8c5348f Z-height fix V2b (PR#2351)
here the other two occurences of `Z_PROBE_OFFSET_FROM_EXTRUDER` are
replaced with `zprobe_zoffset`.
2015-07-02 20:30:40 -05:00
Todd Swindoll
a111fbbd0a z-probe offset fix (PR#2361)
verified via 1.0.2 tag that compiles by multiple people,
credit for the fix goes to paulusjacobus for the initial find and
sniffle for the correction so M851 works.
2015-07-02 20:28:07 -05:00
Scott Lahteine
9682ed455e Fix comment on M83, add comment to prepare_move 2015-06-28 08:20:19 -05:00
AnHardt
36746143a1 Correct output of M48 (PR#2336)
n_samples is an uint8_t .
Got printouts like:
50 of 2  ...
2015-06-27 06:08:40 -05:00
Scott Lahteine
f6ca5a8da8 Allow "M110 N123" without a checksum 2015-06-26 18:13:54 -05:00
Scott Lahteine
aaad65ff5d Include a comment documenting M110 2015-06-26 18:13:54 -05:00
Scott Lahteine
862c72b030 Put the mandatory test of gcode_N first 2015-06-26 18:13:54 -05:00
Scott Lahteine
30976f9773 Allow M110 to handle a second N argument 2015-06-26 18:13:53 -05:00
Scott Lahteine
5ccb1c9e7d Use millis for M600 audio feedback interval 2015-06-25 20:45:03 -05:00
Scott Lahteine
fb16a83b8a Cleanup M600 documentation comments 2015-06-25 20:45:03 -05:00
Scott Lahteine
97ec224d72 Replace target with destination in M600 2015-06-25 20:45:03 -05:00
Scott Lahteine
4ce9ddbb74 Check the temperature before filament change 2015-06-25 20:45:03 -05:00
AnHardt
722829b058 Move buzzing code to buzzr.h & buzzer.cpp (PR#2307)
at least the lcd independent part from Marlin_main.cpp.
2015-06-22 22:31:48 -04:00
schlotzz
1e9cf905c7 Enable ZigZag AutoBedLeveling on Deltas (PR#2273)
ZigZag has been disabled by fault due to do_topography_map
2015-06-15 20:26:25 -05:00
AnHardt
6ab7b560af Rework buzzing (PR#2296)
by:
Moving HAS_LCD_BUZZ macro to Coditionals.h
Renaming HAS_LCD_BUZZ to HAS_BUZZER to make clear is has nothing to do with the lcd.
Removing the ULTRALCD condition.

Moving declaration of lcd_buzz() out of the ULTRA_LCD block in ultralcd.h
Moving definition of lcd_buzz() out of the ULTIPANEL block in ultralcd.cpp
Renaming lcd_buzz() to buzz() to make clear is has nothing to do with the lcd.

All buzzing code is now only dependent on the existence of a BEEPER-pin or the definition of a LCD_USE_I2C_BUZZER.

To do: Check the conditions for the BEEPER-pin in all pin-files.
2015-06-15 06:13:26 -05:00
Scott Lahteine
29122db2fa Fix ULTRA_LCD spelling in HAS_LCD_BUZZ 2015-06-15 06:12:34 -05:00
Scott Lahteine
e2a4a83586 Don't re-apply Z_RAISE_BETWEEN_PROBINGS in probe_pt (PR #2281) 2015-06-12 22:39:35 -05:00
MagoKimbra
eb81982fcd Fix error next command in autotune (PR#2274)
Now send only temperature for T or B, but not send OK.
Host interprets the line to show the right temperature, but not in
response to M105 then stop and send commands until it ends the autotune.
2015-06-12 07:10:38 -05:00
AnHardt
55b23c896a Optimise out_of_range_error() (PR#2265)
by avoiding the strncopy()
2015-06-12 02:20:40 -05:00
AnHardt
45642b7fe8 Respect DISABLE_AXIS settings (PR#2216)
when DEFAULT_STEPPER_DEACTIVE_TIME is over
instead of simply turn off all.
2015-06-11 11:35:05 -05:00
Scott Lahteine
962b107341 Prevent current_command_args from bypassing nul (PR#2270) 2015-06-09 16:07:10 -05:00
Scott Lahteine
ff6081be3a Parse N[0-9]+[ ]* differently (PR #2263)
More general solution to skip N[0-9]+[ ]* in the parser as in #2218
2015-06-08 17:06:49 -05:00
Scott Lahteine
96a3fba8ac Reverse the sign of zprobe_zoffset
- When editing on the LCD, minus now means below the nozzle
- Stores the opposite sign in EEPROM, so bumped to “V20”
2015-06-08 05:09:27 -05:00
paclema
8d295547be * Auto filament change on CHANGEFILAMENT feature. Now you can activate this option that extrude filament until you press the button. 2015-06-06 19:45:45 -05:00
Richard Wackerbarth
ad09d6a60f 3 Step Allen Key Probe 2015-06-06 17:48:27 -05:00
AnHardt
e400fce271 Merge pull request #2221 from MagoKimbra/Dryrun
Insert Debug DRYRUN Repetier Host compatible
2015-06-03 12:30:48 +02:00
AnHardt
c3fe6e61ae Merge pull request #2229 from AnHardt/position-out-of-range
Fix out_of_range_error()
2015-06-03 09:46:22 +02:00
AnHardt
d1f4471000 Merge pull request #2146 from Wackerbarth/Versioning
Versioning
2015-06-02 18:31:21 +02:00
AnHardt
17b0ec84ed Fix out_of_range_error()
For sprintf_P() the first parameter has to be a `char*` not `const char*`.
2015-06-02 11:50:32 +02:00
AnHardt
35af5ef23e Merge pull request #2225 from Wurstnase/naming
consistency name for multiplier
2015-06-02 10:18:22 +02:00
wurstnase
e7e964432b consistency name for multiplier
replace extruder_multiply with extruder_multiplier
like feedrate_multiplier or volumetric_multiplier
2015-06-01 22:33:22 +02:00
MagoKimbra
76306f9073 Insert Debug DRYRUN Repetier Host compatible 2015-06-01 18:34:45 +02:00
MagoKimbra
881146bc22 Fix problem Width Cura 2015-06-01 17:25:32 +02:00
AnHardt
9d2a980bcf Merge pull request #2170 from thinkyhead/beep_M600_elsewise
Slight size reduction by adding idle()
2015-05-30 12:42:32 +02:00
AnHardt
2728dc0606 Merge pull request #2194 from thinkyhead/reduce_strings
Redo "invalid extruder" to save 304 bytes
2015-05-30 11:05:08 +02:00
Scott Lahteine
be5236e839 Reduce setTargetedHotend by removing the switch 2015-05-29 18:03:58 -07:00
Scott Lahteine
06f401e7e5 Redo "invalid extruder" to save 264 bytes
- Use `setTargetedHotend` in `M200`, as with other commands that use
`T` for the extruder
- Synthesize the "invalid extruder" message, obviating several long
strings
2015-05-28 22:25:28 -07:00
Scott Lahteine
1a882bcc2e Merge pull request #2193 from thinkyhead/ignore_unrecognized_commands
Ignore unknown commands if they start with G, M, or T
2015-05-28 22:03:48 -07:00
Scott Lahteine
a672872717 Merge pull request #2187 from AnHardt/MAX6675M105
Print active extruder with M105 for MAX6675
2015-05-28 18:12:48 -07:00
Scott Lahteine
9beed830eb Drop commented code_is_good lines 2015-05-28 17:53:47 -07:00
Scott Lahteine
068d4a1eb2 Ignore unknown commands if they start with G, M, or T 2015-05-28 17:44:09 -07:00
Scott Lahteine
c5c9d12630 Merge pull request #2183 from AnHardt/displayinit
Initialize the display earlier
2015-05-28 16:29:18 -07:00
Scott Lahteine
0564625757 Update M33 for new gcode parser 2015-05-28 14:17:39 -07:00
AnHardt
af7e3f5076 Print active extruder with M105 for MAX6675
Was omitted when T0 is a MAX6675.
2015-05-28 19:03:16 +02:00
AnHardt
f0523b5816 Initialize the display earlier
to have it ready to display errors during (temperature)-setup.
2015-05-28 16:08:17 +02:00
Scott Lahteine
03d5709b09 M110 is a known command
- The command parser now displays “unknown command” in more cases.
Known commands must be added to the `switch` inside `process_commands`
to suppress the error.
2015-05-26 20:31:18 -07:00
Scott Lahteine
d76a01194d Slight size reduction by adding idle() 2015-05-26 20:08:21 -07:00
Richard Wackerbarth
5ea139fd79 Revised Versioning mechanism 2015-05-25 15:53:14 -05:00
Scott Lahteine
68f6f149d0 Reduce code size with out_of_range_error function
- Affects code size when automatic bed leveling is enabled
2015-05-24 20:18:02 -07:00
Scott Lahteine
b55f8718c3 Indent G90/G91, G92 2015-05-22 17:34:08 -07:00
Scott Lahteine
b0d520b109 Indent G30, G31/G32 2015-05-22 17:33:17 -07:00
Scott Lahteine
ffe27a6225 Indent G29 2015-05-22 17:32:46 -07:00
Scott Lahteine
86083badc2 Indent G4, G10/G11, G28 2015-05-22 17:32:27 -07:00
Scott Lahteine
47d7a9cb5e Indent G2/G3 2015-05-22 17:31:38 -07:00
Scott Lahteine
350f239d84 Indent G0/G1 2015-05-22 17:31:24 -07:00
Scott Lahteine
15a2351675 No need for +1 on initial seen_pointer 2015-05-22 15:31:30 -07:00
Scott Lahteine
550dd87b2a Set seen_pointer before calling code_value 2015-05-22 15:11:48 -07:00
Scott Lahteine
04a1622172 Merge pull request #2127 from Wackerbarth/Kossel_Pro
Kossel Pro
2015-05-21 18:43:26 -07:00
Scott Lahteine
f919a2fed1 Merge pull request #2134 from AnHardt/preheat-all
Shift call of start_watching_heater() into setTargetHotend()
2015-05-21 18:36:28 -07:00
AnHardt
0c0ace2a04 Remove start_watching_heater() fom M104 and M109 2015-05-22 01:44:50 +02:00
Scott Lahteine
bde9c70d42 Suppress the line mismatch error after M303 2015-05-21 16:27:22 -07:00
Scott Lahteine
50bd7493cc Merge pull request #2108 from thinkyhead/m33_long_filename_host_support
M33 LONG_FILENAME_HOST_SUPPORT
2015-05-21 16:22:47 -07:00
Scott Lahteine
4d11b29959 Merge pull request #2113 from thinkyhead/command_sanitizer
Command sanitizer
2015-05-21 16:21:58 -07:00
Richard Wackerbarth
735bf2d35f Describe Custom M Code 2015-05-21 08:06:33 -05:00
Scott Lahteine
f39658c822 M120 and M121 are reversed 2015-05-21 00:17:44 -07:00
AnHardt
89d2ee6f13 Make output on display dependant of ULTRA_LCD 2015-05-20 22:03:16 +02:00
AnHardt
f4a93ed997 Add a string parameter to kill()
Makes the output on the LCD adjustable.
2015-05-20 20:53:48 +02:00
Scott Lahteine
a0f362c735 Simplify & optimize with current_command_args 2015-05-18 07:08:04 -07:00
Scott Lahteine
adc8fcb77f More parser comments, optimize code_seen, save with goto 2015-05-18 07:08:04 -07:00
Scott Lahteine
c6d8dd19d9 use fetched value 2015-05-18 07:08:04 -07:00
Scott Lahteine
1116e13f5a Further optimization of command parser 2015-05-18 07:08:03 -07:00
Scott Lahteine
3a4c3ab76e Pre-sanitize the command before handling
- Use a global pointer for the current sanitized command
- Pre-sanitize the current command to bypass `N` and nullify `*`,
removing the need for handlers to bypass, ignore, or nullify these
parts, and reducing overhead for `code_seen`, etc.
- Pre-skip leading whitespace.
- Only look for G, M, T codes at the start of the command.
- Verify that G, M, T codes are followed by command codes.
2015-05-18 07:06:51 -07:00
Scott Lahteine
0f2c9bacfd M33 LONG_FILENAME_HOST_SUPPORT 2015-05-17 17:36:32 -07:00
Scott Lahteine
3feaef6526 Have G92 set the nozzle position on Delta and SCARA 2015-05-17 17:08:05 -07:00
Scott Lahteine
6c27eaf864 Merge pull request #2101 from thinkyhead/code_style
Code style and a dangling "else"
2015-05-17 03:39:08 -07:00
Scott Lahteine
d580a0d186 Use "+=" in plane rotation 2015-05-17 01:51:14 -07:00
Scott Lahteine
2f3a410cb0 Fix a potential hanging "else" bug 2015-05-17 01:50:30 -07:00
Scott Lahteine
b83e3f0905 Combine "Bed X: " strings 2015-05-17 01:49:52 -07:00
Scott Lahteine
7dfb8becdb Adjust some names and types in Marlin_main.cpp 2015-05-17 01:48:51 -07:00
Scott Lahteine
c966aa26ff Comments in Marlin_main.cpp 2015-05-17 01:47:53 -07:00
Scott Lahteine
c54a2ea042 Adjust spacing in Marlin_main.cpp and stepper.* 2015-05-17 01:47:02 -07:00
Scott Lahteine
072625ccad Update headings in Marlin_main.cpp and stepper.cpp 2015-05-17 01:44:53 -07:00
Scott Lahteine
16032f149f Rename to codenum as a consistency 2015-05-16 23:17:35 -07:00
Scott Lahteine
273a4a253f Merge pull request #2096 from thinkyhead/cherry_picking3
Hide M117 with no LCD
2015-05-16 21:10:28 -07:00
Scott Lahteine
64825a3d1e Merge pull request #2095 from thinkyhead/cherry_picking2
Add gcode_line_error to reduce code size
2015-05-16 21:09:15 -07:00
Scott Lahteine
ca79282eaf Hide M117 with no LCD 2015-05-16 20:59:04 -07:00
Scott Lahteine
ce218cafdb Add gcode_line_error to reduce code size 2015-05-16 20:54:58 -07:00
Scott Lahteine
46d59784ad Rename preocess_command to process_next_command 2015-05-16 20:47:40 -07:00
Scott Lahteine
19166a92e4 Merge pull request #2057 from Wurstnase/serial_wait
add plan buffer remaining for 'P' and block buffer remaining 'B'
2015-05-14 04:57:08 -07:00
Scott Lahteine
e97fcafd0e Merge pull request #2076 from thinkyhead/mendel_inverting
Use MSG_OK in M105
2015-05-14 04:54:11 -07:00
Scott Lahteine
0f6cd3640b Drop extraneous ok_to_send 2015-05-14 04:38:09 -07:00
Scott Lahteine
0ce355d9e7 Use MSG_OK in M105 2015-05-14 03:33:38 -07:00
Scott Lahteine
7b3acfbb6f Merge pull request #2072 from thinkyhead/better_arc_code
Consolidate arc code, remove motion_control.*
2015-05-14 00:27:22 -07:00
Scott Lahteine
68ce419147 Note on segment size 2015-05-13 19:11:36 -07:00
Scott Lahteine
8b92249f18 Bring arc_offset into auto scope 2015-05-13 19:00:46 -07:00
Scott Lahteine
80807b2d71 Consolidate arc code, remove motion_control.* 2015-05-13 18:52:41 -07:00
Scott Lahteine
f65833931d Formatting tweaks 2015-05-13 02:02:19 -07:00
Scott Lahteine
747fd5801c Merge pull request #2055 from thinkyhead/thermal_unified
Combine thermal runaway and watch-period
2015-05-12 08:04:29 -07:00
Scott Lahteine
6e5572228d Merge pull request #2064 from thinkyhead/wait_before_g28
Split up prepare_move by type
2015-05-12 07:53:11 -07:00
Scott Lahteine
27ad381e25 Allow fractional seconds in G4 and M0 2015-05-12 07:52:08 -07:00
Scott Lahteine
b2bd9aae7c SCARA_SEGMENTS_PER_SECOND 2015-05-12 04:18:15 -07:00
Scott Lahteine
bd20bd5444 Merge pull request #2063 from chris-bo/autobed_sled
improve sled handling
2015-05-12 03:29:21 -07:00
Scott Lahteine
9e95ceb3fc Split up prepare_move by type
- For better encapsulation add inlines for each prepare_move type
- Move controllerFan vars inside the function as statics
- Some formatting cleanup
- Rename `ClearToSend` as `ok_to_send`
2015-05-12 02:08:20 -07:00
Christian Bohn
f48599f172 add pin definition to some motherboards 2015-05-12 10:02:23 +02:00
Scott Lahteine
b5200e184c Remove extra setup_for_endstop_move 2015-05-12 01:01:53 -07:00
Scott Lahteine
8d814de558 Return void in prevent_dangerous_extrude 2015-05-12 00:55:00 -07:00
Scott Lahteine
367e2eb9f4 Global setup_for_endstop_move 2015-05-12 00:51:22 -07:00
Scott Lahteine
fa951f8a0b Always do st_synchronize() before G28 2015-05-12 00:31:51 -07:00
Christian Bohn
27a3b1d895 disable sled pin by default 2015-05-12 08:51:01 +02:00
Christian Bohn
fb44b53ae3 sled improvements
- create sled pin definition
- G28 Works with sled
2015-05-11 23:22:19 +02:00
Wurstnase
46d1932380 add plan buffer remaining for 'P' and block buffer remaining 'B' 2015-05-11 13:04:00 +02:00
Scott Lahteine
8a0dc4d54a Merge pull request #1922 from Wurstnase/serial_wait
Serial wait
2015-05-10 23:10:25 -07:00
Wurstnase
526ad82d20 activate advanced_ok and no_timeout 2015-05-11 08:01:51 +02:00
Scott Lahteine
2445ae3d3a Combine thermal runaway and watch-period
- Make thermal protection for all hotends and/or bed into simple
switches
- Now enable `WATCH_TEMP_PERIOD` when `THERMAL_PROTECTION_HOTENDS` is
enabled
- Move detailed thermal parameters to `Configuration_adv.h`
- Add sanity checks to warn about old configurations
- Change `WATCH_TEMP_PERIOD` to seconds instead of milliseconds
2015-05-10 22:52:01 -07:00
Scott Lahteine
4097207c75 Merge pull request #2041 from thinkyhead/watch_temp
More thermal protection
2015-05-10 21:39:05 -07:00
Scott Lahteine
9b3d4380d3 Only watch the heater that was set 2015-05-10 20:26:45 -07:00
Scott Lahteine
f73f4ce555 Make some z probe and servo code tweaks 2015-05-09 19:11:19 -07:00
Scott Lahteine
54deb9eea3 Enable WATCH_TEMP_PERIOD by default 2015-05-08 22:36:02 -07:00
Wurstnase
0cb87795a3 advanced 'ok'
ok N(linenumber) P(bufferremaining)
the host can use this to send the data much faster.

Some pseudo code:
If (bufferremaining > 0)  send command
## as long there is free buffer send command

Also
if (linenumber > lastsend - bufferremaining) send command
## as long last linenumber received is bigger than lastsend (host) - last bufferremaining received
2015-05-08 22:28:51 +02:00
Wurstnase
182e0d99c9 Merge remote-tracking branch 'Marlin8bit/Development' into serial_wait 2015-05-08 21:27:18 +02:00
Scott Lahteine
7f3252eea9 Merge pull request #1999 from paclema/Filrunout_configurable_script
Added configurable script for filrunout from configuration.h
2015-05-08 04:39:59 -07:00
Scott Lahteine
79633a74ab Fix MBL compile error 2015-05-06 14:25:13 -07:00
Scott Lahteine
777f2d3820 Merge pull request #2018 from fmalpartida/bugFixing
Bug corrected: persistent HOMING message when HOME button pressed for homing.
2015-05-05 00:12:32 -07:00
Scott Lahteine
ecb46de349 Merge pull request #2013 from bq/Fix_lowercase
Fixed lowercase change missing on commit a22a228b.
2015-05-04 23:50:56 -07:00
fmalpartida
150a35eff8 Bug corrected:
Persistent homing message.
Message was declared as an alert, therefore it was persistent.
Updated to message.
2015-05-04 19:48:49 +02:00
Gina Häußge
ab246ab032 Reverting changes to error messages on serial console
This reverts the changes done to the error message for line number mismatches done in commit d43cc2dd5f
2015-05-04 15:03:00 +02:00
Ivan Galvez Junquera
59529b755d Fixed lowercase change missing on commit a22a228b.
Servo.cpp and Servo.h were changed to lowercase in Makefile but not their actual filenames.
2015-05-04 09:44:34 +02:00
Scott Lahteine
1f039cde61 Merge pull request #1992 from thinkyhead/too_many_probes
Stow Z probe on M402 without extra raise
2015-05-03 20:40:26 -07:00
Scott Lahteine
ca8cec8e8a Merge pull request #1998 from paclema/Filament_runout_fix
Fixed sintaxis error of filament runout
2015-04-29 19:53:25 -07:00
Scott Lahteine
d4c74b8f8c Don't apply M428 if an error occurs
- Also move audio feedback into the command
- Added shorthand for `lcd_buzz` availability
2015-04-29 19:05:48 -07:00
Scott Lahteine
d065d37822 Add M428 to set home_offset logically 2015-04-29 18:26:16 -07:00
paclema
013a09dbe6 Added configurable script for filrunout form configuration.h 2015-04-29 21:38:40 +02:00
paclema
4dcc0fd55a Fixed sintaxis error of filament runout 2015-04-29 21:32:27 +02:00
Scott Lahteine
ce3caf447b Tweak how homeaxis deploys and stows 2015-04-28 19:17:48 -07:00
Scott Lahteine
a235dca79c Stow z on M402 without extra raise 2015-04-28 19:10:07 -07:00
Scott Lahteine
3688256f86 Merge pull request #1974 from thinkyhead/eeprom_in_gcode
Make EEPROM reproducible in GCode
2015-04-27 22:35:41 -07:00
Scott Lahteine
31516e2a3b Merge pull request #1985 from Arengorn/Development
Update of servo.h
2015-04-27 22:10:02 -07:00
Scott Lahteine
0f687b5dda Merge branch 'Development' into eeprom_in_gcode
Latest upstream commits
2015-04-27 21:47:47 -07:00
Scott Lahteine
28aef684b4 Merge pull request #1957 from Voxel8/sjk/home_y_before_x
Allow Y to home before X with option in Configuration_adv.h.
2015-04-27 21:41:14 -07:00
Scott Lahteine
71a0b1a5bb Disable endstops between homing bumps 2015-04-27 21:14:30 -07:00
Scott Lahteine
c36226c4dc Fix homing Z position
Add `sync_plan_position()` after `axis_is_at_home(axis)` to keep the
planner position in sync when homing.
2015-04-27 20:55:19 -07:00
Scott Lahteine
ff178d8cf7 Change M421 to take coordinates
This makes `M421` more amenable for irregular matrices
2015-04-27 19:48:34 -07:00
Bernardo
ff67ee73fc Update Marlin_main.cpp
Corrected "servo.h" to "Servo.h" because of the updated filename.
2015-04-27 23:29:16 -03:00
Steve Kelly
98ca46006c Allow Y to home before X with option in Configuration_adv.h.
This addresses comments in #1956 and #1079. In particular, this is useful
when both endstops are stationary on a CoreXY system, and the Y axis needs
to be homed before the X so the flags are aligned.
2015-04-27 16:17:30 -04:00
Scott Lahteine
0fca084ea6 Make EEPROM reproducible in GCode
With these changes the output of `M503 S0` is all you need to restore
the EEPROM. Building on this it is straightforward to save and restore
the EEPROM state using the SD card or external GCode file.

- Added `M145` to set “heatup states” for the LCD menu
- Added `M420` to toggle Mesh Bed Leveling
- Added `M421` to set a single Mesh coordinate
- Extended `Config_PrintSettings` with added M codes
- Cleaned up some comments here and there
2015-04-26 20:56:33 -07:00
Scott Lahteine
d43cc2dd5f M111 - Debug Level
- Add `M111` as a standard option to set the debug level
- Implement `DEBUG_ECHO` in `process_commands`
- Other debug levels (e.g., `DEBUG_DRYRUN`) need more work
2015-04-26 20:08:45 -07:00
Scott Lahteine
a22a228bcc Rename files to move them in the IDE 2015-04-25 21:04:54 -07:00
Scott Lahteine
0438f0d835 Merge pull request #1924 from thinkyhead/raise_z_for_m401_m402
Raise Z for M401 and M402
2015-04-24 22:41:12 -07:00
Scott Lahteine
b275946a52 Merge pull request #1966 from thinkyhead/g4_dwell_message
G4 shows status message only if no message is set already
2015-04-24 22:02:37 -07:00
Scott Lahteine
182f2cda35 Minor cleanup of M48 2015-04-24 21:26:36 -07:00
Scott Lahteine
3a6fd912cd Latest upstream commits, merged 2015-04-24 21:14:13 -07:00
Scott Lahteine
3c9e94e035 Merge pull request #1964 from AnHardt/Max6675again
Add variant for MAX6675 in M104
2015-04-24 20:44:45 -07:00
Scott Lahteine
56ff46eb8b Improve code_has_value test 2015-04-24 20:43:16 -07:00
Scott Lahteine
ce142afdda G4 shows status message only if no message is set already
- Address issue raised in #1961
2015-04-24 20:13:01 -07:00
Scott Lahteine
35e79d56a5 Remove set-coordinate extension of G28 2015-04-24 19:23:12 -07:00
Scott Lahteine
3a74bb5039 Merge pull request #1945 from Wurstnase/max_endstopp
Max endstopp
2015-04-24 19:17:38 -07:00
AnHardt
0fed46360c Add variant for MAX6675 in M104
Else will throw error:
@:0 B@:0
Error:No thermistors - no temperature
[ERROR] Error:No thermistors - no temperature

when no bed is defined
2015-04-24 16:43:19 +02:00
Scott Lahteine
588ed70d4a Latest upstream commits, merged 2015-04-23 21:18:48 -07:00
Scott Lahteine
0165560333 Apply zprobe_zoffset in axis_is_at_home
Ensure the probe offset will always be included when homing Z.
2015-04-23 21:12:38 -07:00
Scott Lahteine
075386e7fe Merge pull request #1959 from thinkyhead/lcd_move_rate
Include axis parameter to ultralcd's line_to_current
2015-04-23 21:06:57 -07:00
Scott Lahteine
2558c10c6c Use the slower feedrate for XY axes 2015-04-23 20:06:17 -07:00
Scott Lahteine
64268f3312 Fixup axis_is_at_home a little 2015-04-23 18:16:44 -07:00
Scott Lahteine
996d0a9185 Squish the code down a little 2015-04-23 18:06:36 -07:00
Scott Lahteine
8534bc376c Fix homing of YZ with DUAL_X_CARRIAGE 2015-04-23 17:56:37 -07:00
Scott Lahteine
3b97a7d446 Merge pull request #1944 from AnHardt/beep2
More Beeper clean up
2015-04-23 17:50:02 -07:00
Wurstnase
be9e4ceddc fix typo
c'n'p ftw :/
2015-04-23 10:35:14 +02:00
unknown
c26d816839 filter any 0 2015-04-22 12:09:57 +02:00
Wurstnase
61ae43f35e v <-> code_value 2015-04-20 23:31:10 +02:00
Wurstnase
da0d91a79b max endstopp
no user will home to 0 with a max endstopp
2015-04-20 23:28:46 +02:00
AnHardt
064f2b37d0 More Beeper clean up.
Centralised beep code to lcd_buzz().
From gcode_M300() and lcd_quick_feedback().

Enforced max. duration for M300 to 5 seconds.

Corrected description in 'Configuration.h'

LCD_FEEDBACK_FREQUENCY_HZ 0 gives now a silent delay of
LCD_FEEDBACK_FREQUENCY_DURATION_MS.
2015-04-20 11:11:13 +02:00
Wurstnase
92575cecca new timout/add adv_ok 2015-04-20 00:22:40 +02:00
AnHardt
671aaf2dc9 Minor fix for M300
Corrected wrong order of parameters.
2015-04-19 13:25:20 +02:00
Scott Lahteine
d931220a65 Tweak comments 2015-04-18 23:12:29 -07:00
Scott Lahteine
47847765e2 Add M410 QuickStop command 2015-04-18 23:07:48 -07:00
Wurstnase
b09a957fce make 'wait' optional and mark as workaround 2015-04-16 21:42:54 +02:00
Scott Lahteine
63b98b8280 Raise Z for M401 and M402 2015-04-16 07:24:33 -07:00
wurstnase
d69da22f7c last_command_time inside get_command() 2015-04-16 16:20:23 +02:00
wurstnase
574e2d856e remove config 2015-04-16 13:07:20 +02:00
paclema
cde5eee2a5 Removed unnecessary comments 2015-04-15 19:01:09 +02:00
paclema
e1b69db6d1 Fixed M48 mismatch between n and P parameter on documentation 2015-04-15 18:17:58 +02:00
Scott Lahteine
e0e68c5cbc Rename servos[] array in Marlin to servo[] 2015-04-14 03:13:25 -07:00
Scott Lahteine
642f6a92bc fix type of code_has_value 2015-04-13 18:02:17 -07:00
Scott Lahteine
17ad80c1e1 Spacing in XYZ_CONSTS 2015-04-13 17:58:47 -07:00
Scott Lahteine
09d60e0128 Naming and code comments 2015-04-13 17:17:36 -07:00
Mehmet Sutas
5a9e45cc4a Fix Syntax Error Filament Runout Statement 2015-04-13 22:37:18 +03:00
Scott Lahteine
ccddc280be Apply three more commits 2015-04-12 22:47:44 -07:00
Scott Lahteine
ac2b23f574 Homing fixes
- Prevent `Z_SAFE_HOMING` from homing Z twice in some cases
- Allow `G28` with XYZ values of 0 to explicitly set the position
- Don’t add `home_offset` when setting XYZ explicitly in `G28`
- Add `code_has_value` function to check for the presence of a numeric
value (could just test for space or nul to allow other types of values)
2015-04-11 20:06:48 -07:00
Scott Lahteine
5fe382949b Some G-Codes comment cleanup 2015-04-10 16:16:13 -07:00
Scott Lahteine
8b16ebe705 Break out prevent_dangerous_extrude feature
- It’s inline here, but could be a macro and duplicated for
`planner.cpp`
2015-04-09 22:40:37 -07:00
Scott Lahteine
9189cc66ab Fix moves for DELTA for MANUAL_BED_LEVELING
- Use `line_to_current` in place of `plan_buffer_line`
2015-04-09 04:32:14 -07:00
Scott Lahteine
2ca099d1e7 Merge pull request #1876 from thinkyhead/cold_extrude
Catch dangerous extrude before trying several
2015-04-09 03:21:19 -07:00
Scott Lahteine
a00ebf03d4 Merge pull request #1868 from AnHardt/LCD_STR
Moved the definitions of the LCD_STR_* to Conditionals.h
2015-04-09 01:56:23 -07:00
Scott Lahteine
1269c445ab Catch dangerous extrude before trying several 2015-04-09 01:40:48 -07:00
AnHardt
540dbb35e2 And an other MSG_BED in Marlin_main.cpp 2015-04-09 01:16:06 +02:00
AnHardt
14d4419e16 Replaced SERIAL_PROTOCOLPGM(MSG_BED) with SERIAL_PROTOCOLPGM("Bed")
Resolved some warnings in Marlin_main.cpp regarding compares of signed and unsigned integers by replacing 'int' or 'uint16_t' with 'uint8_t'.
2015-04-08 23:59:01 +02:00
AnHardt
6a514f3dc9 Aplied HAS_LCD_CONTRAST also to Marlin_main.cpp
and cleaned typo.
2015-04-08 13:26:29 +02:00
Scott Lahteine
3162971cd6 current_position not static 2015-04-08 01:05:39 -07:00
Scott Lahteine
27cb90da8b IsStopped / IsRunning inline 2015-04-08 00:56:19 -07:00
Scott Lahteine
e03da4805b Merge pull request #1774 from epatel/Development
Mesh bed leveling: Added G29 S3 + finer display steps during manual input + bug fix
2015-04-07 19:24:46 -07:00
Scott Lahteine
f7c4e7e19f Fix G29 not deploying in some instances 2015-04-07 15:38:29 -07:00
Edward Patel
002340f32c Merge branch 'Development-Marlin' into Development 2015-04-07 22:49:12 +02:00
Scott Lahteine
c379f17117 Encapsulate setting of homing_bump_feedrate 2015-04-06 23:21:33 -07:00
Scott Lahteine
d20f42c883 Don't stow the probe until the last grid point!
- Address Issue #1682 at hash #issuecomment-89756858
2015-04-06 20:58:09 -07:00
Scott Lahteine
6d084c017f Fix typo in FWRETRACT handler
Should be `retracting` and not `retract`
2015-04-06 17:04:22 -07:00
Edward Patel
2f0081bbb5 Compile error fix! Fix for merge artifacts. 2015-04-05 04:16:16 +02:00
Edward Patel
ea10601406 Merge branch 'Development-Marlin' into Development
Conflicts:
	Marlin/Configuration.h
	Marlin/Marlin_main.cpp
2015-04-05 04:06:02 +02:00
Scott Lahteine
61f8394361 Compare indices instead of floats for probe actions 2015-04-04 05:01:16 -07:00
Scott Lahteine
0935084141 Fix manage_inactivity
- Document `manage_inactivity` function
- Allow `EXTRUDER_RUNOUT_PREVENT` to work with all extruders
- Use faster `memcpy` for copying coordinates
2015-04-03 23:42:50 -07:00
Scott Lahteine
c065da52ec Spacing and spelling 2015-04-03 22:54:48 -07:00
Scott Lahteine
8680b515b0 Fix missing tmp_extruder -> target_extruder 2015-04-03 22:12:49 -07:00
Scott Lahteine
c185912c19 Latest upstream commits, mostly 2015-04-03 21:58:48 -07:00
Scott Lahteine
1e5c18bb14 Add code_value_short and SERIAL_CHAR 2015-04-03 21:43:30 -07:00
Scott Lahteine
84e4edaea7 Add M48 comment for #1794 2015-04-03 19:52:00 -07:00
Scott Lahteine
b98ebd517e disable / enable_all_steppers functions 2015-04-03 19:25:22 -07:00
Scott Lahteine
713953d8c1 Upstream commits, allow no extruder in M105 2015-04-03 19:16:38 -07:00
Scott Lahteine
8f893eb8df Merge pull request #1798 from thinkyhead/fixup_probing
Fix probe height at G28 start
2015-04-03 19:03:00 -07:00
Scott Lahteine
dde7e11f8e Merge branch 'Development' into fixup_tr
Latest upstream commits
2015-04-03 18:56:52 -07:00
Scott Lahteine
abd7fc36b6 Fix probe height at G28 start 2015-04-03 18:54:55 -07:00
Scott Lahteine
610c8c5471 Merge pull request #1795 from thinkyhead/fixup_probing
Finish pin tests
2015-04-03 18:44:44 -07:00
Scott Lahteine
e4934164e4 Merge pull request #1790 from Wurstnase/fix_home_z
fix feedrate for homing z
2015-04-03 18:35:09 -07:00
Scott Lahteine
a469d796e1 Add cleanups needed for #1772 2015-04-03 18:14:57 -07:00
Scott Lahteine
c0ca26cd50 Merge branch 'Development' into fixup_probing
Latest upstream commits
2015-04-03 18:05:17 -07:00
Scott Lahteine
5c1f08a35f Merge pull request #1772 from croadfeldt/Merge_cleanup
Z_PROBE_ENDSTOP
2015-04-03 18:04:31 -07:00
Scott Lahteine
92119d0f7d Static delta[] for SCARA 2015-04-03 16:46:56 -07:00
Scott Lahteine
6b919e14c1 Group all universal variables 2015-04-03 15:45:41 -07:00
Scott Lahteine
21cd2e4fae Merge branch 'Development' into fixup_probing
Latest upstream commits
2015-04-03 15:32:15 -07:00
Scott Lahteine
0e8182bbf2 Additional pin tests, cleanup 2015-04-03 15:31:35 -07:00
Wurstnase
45565b680d second wrong feedrate 2015-04-03 18:01:28 +02:00
Wurstnase
581b2aae04 fix feedrate for homing z
max_feedrate is in mm/s. line_to_destination needs a feedrate in mm/min because there is feedrate/60.
2015-04-03 16:11:32 +02:00
AnHardt
23cd54755f Fix typo in Marlin_main.cpp
related to current_position[Z_AXIS] and retract_zlift.

'+ =' -> '+='

Fix for #1786
2015-04-02 14:50:31 +02:00
Scott Lahteine
e96df67630 Clarify thermal_runaway_protection
- Add comments documenting `thermal_runaway_protection`
- Add an enum for the thermal runaway states
- Add macros for temperature helper functions
- Fix a glitch with the z probe sled in homeaxis
2015-04-02 05:10:14 -07:00
Edward Patel
6b91b7b411 Mesh bed leveling: Added G29 S3 + finer steps in manual probing.
* Use "G29 S3 Xn Yn Zn.nn" to modify bad probed point manually
* Changed manual Z steps from 0.05 to 0.025 and made brought it to Configuration.h
2015-04-01 21:18:51 +02:00
Chris Roadfeldt
26dc80bf2d Typo fixed... 2015-04-01 13:47:17 -05:00
Chris Roadfeldt
a57862e29f Cleaning up code in prep for merge with upstream. 2015-04-01 11:40:24 -05:00
Chris Roadfeldt
745d9fe1a4 Merge remote-tracking branch 'MarlinFirmware/Development' into Merge_cleanup
Conflicts:
	Marlin/Marlin_main.cpp
2015-04-01 10:31:02 -05:00
Scott Lahteine
9593f09b99 Merge pull request #1764 from thinkyhead/probe_leveling
Fix homing and leveling
2015-04-01 02:00:39 -07:00
Scott Lahteine
72c7de3570 Cleanup M48 2015-04-01 01:48:45 -07:00
Scott Lahteine
97a258b0b0 Clean up, document home_axis 2015-04-01 01:44:13 -07:00
Chris Roadfeldt
a508d835db Changed Z_PROBE_AND_ENDSTOP to Z_PROBE_ENDSTOP.
Updated documentation in Configuration.h.
Cleaned up and commented some code relating to Z_PROBE_ENDSTOP.
Separated Z_MIN_ENDSTOP and Z_PROBE_ENDSTOP completely.
2015-04-01 02:14:55 -05:00
Chris Roadfeldt
fdb4ddbdea Merge remote-tracking branch 'MarlinFirmware/Development' into Development 2015-04-01 00:52:08 -05:00
Scott Lahteine
1c7391717e Include sync_plan_position_delta for SCARA also 2015-03-31 19:58:03 -07:00
Scott Lahteine
0b57a2ab8b Merge pull request #1757 from bq/Translation-strings
Added new trasnslatable labels.
2015-03-31 18:56:25 -07:00
Scott Lahteine
18bb6be80e Fix homing and leveling
- Include the current Z when raising the axis after and between probing
- Add `sync_plan_position_delta` for parity with `sync_plan_position`
- Clean up and clarify `M48`, `dock_sled`, and others
2015-03-31 18:52:19 -07:00
Chris Roadfeldt
c89b8368ee Merge remote-tracking branch 'MarlinFirmware/Development' into Development
Conflicts:
	Marlin/Marlin_main.cpp
2015-03-31 11:08:36 -05:00
Ivan Galvez Junquera
d08782386b Added new trasnslatable labels.
* Added MSG_END_HOUR and MSG_END_MINUTE labels to all language files.
* Available translations:
  EN, FR, DE, ES, IT, PT, PT-BR.
2015-03-31 16:59:43 +02:00
Scott Lahteine
97a69d9b1c Correct XYZ after obtaining plan_bed_level_matrix
The current position needs to be updated by using the inverse
`plan_bed_level_matrix` on X, Y, and Z. All moves in the planner are
transformed by the `plan_bed_level_matrix` from this point forward.
2015-03-31 04:24:13 -07:00
Scott Lahteine
5f6962dd90 Merge pull request #1755 from thinkyhead/fixup_config
Raise when not retracting
2015-03-31 03:47:01 -07:00
Scott Lahteine
ae89ccd2c7 Use Z_RAISE_BETWEEN_PROBINGS 2015-03-31 03:45:21 -07:00
Scott Lahteine
9a5a7a3f68 Raise when not retracting
Code to raise the probe before retraction is good, but the code should
always raise the probe, not just when retracting
2015-03-31 03:38:03 -07:00
Scott Lahteine
2a45922afe Restore extruder_offset, init more simply 2015-03-31 02:49:47 -07:00
Scott Lahteine
28792e5731 Fix typo in assignment 2015-03-31 02:10:49 -07:00
Scott Lahteine
bb6174524f Fix EXTRUDER_OFFSET compiler error
- Addressing issue #1741
2015-03-31 02:08:57 -07:00
Chris Roadfeldt
45ece5afb1 Merge remote-tracking branch 'MarlinFirmware/Development' into Development 2015-03-31 03:07:57 -05:00
Chris Roadfeldt
17707e7479 Fixed Z_PROBE_PIN pullup bug.
Documented some additional areas that should be addressed if Z_PROBE is
fully separated from Z_MIN or Z_MAX.
Fixed a documentation error in sanity checks. Servos start at 0 not 1.
2015-03-31 02:56:41 -05:00
Scott Lahteine
50145266cd Merge pull request #1748 from thinkyhead/raise_before_homing
Apply Z_RAISE_BEFORE_HOMING before homing XY
2015-03-30 23:37:41 -07:00
Scott Lahteine
a117b6bff6 Merge pull request #1747 from thinkyhead/progress_bar_tweak
Fix up LCD_PROGRESS_BAR
2015-03-30 23:37:28 -07:00
Chris Roadfeldt
faac2af4af Merge remote-tracking branch 'origin/Development' into Development 2015-03-31 00:03:07 -05:00
Chris Roadfeldt
3be00cce6f Merge remote-tracking branch 'MarlinFirmware/Development' into Development
Conflicts:
	Marlin/Configuration.h
2015-03-30 23:59:01 -05:00
Chris Roadfeldt
e08f8eed05 Revert 06f767d..cba5692
This rolls back to commit 06f767d608.
2015-03-30 23:51:36 -05:00
Chris Roadfeldt
992b07ca57 Don't disable Z_RAISE_BEFORE_HOMING when Z_PROBE_AND_ENDSTOP is enabled. 2015-03-30 22:58:10 -05:00
Chris Roadfeldt
cba5692673 Merge remote-tracking branch 'MarlinFirmware/Development' into Development
Conflicts:
	Marlin/Marlin_main.cpp
	Marlin/stepper.cpp
2015-03-30 22:33:05 -05:00
Scott Lahteine
8500c80b33 Apply Z_RAISE_BEFORE_HOMING before homing XY 2015-03-30 20:22:21 -07:00
Scott Lahteine
5519882eea Fix up LCD_PROGRESS_BAR
- Some messages should not expire with `PROGRESS_MSG_EXPIRE`.
- Simplify conditional for progress bar with sanity checks.
- Rename `messageTick` to `expireStatusMillis` and make it the expire
time.
2015-03-30 18:00:54 -07:00
Scott Lahteine
8c136a5ab5 Conditionals and comments for PS = 0 2015-03-30 16:50:05 -07:00
Scott Lahteine
2faed961ce Allow POWER_SUPPLY 0 for no power switch 2015-03-30 16:39:47 -07:00
Scott Lahteine
baa6787393 Merge pull request #1740 from thinkyhead/fixup_homing
Apply leveling for DELTA
2015-03-30 15:45:33 -07:00
AnHardt
50a732360a Replace extrudemultiply by extruder_multiply[active_extruder]
Fix for #1460.

Seems to work with only one extruder. Can't test this myself with more.
2015-03-30 13:35:03 +02:00
Scott Lahteine
41d258697a Pass the z for after probing to retract_z_probe
A `z_before` value is passed to probe_pt, but the `retract_z_probe`
function assumes that Z is 0, doesn’t add `current_position[Z_AXIS]` as
other cases do. This may be superfluous, so this is a test, and will be
reverted if it has no effect.
2015-03-30 00:45:02 -07:00
croadfeldt
06f767d608 Merge remote-tracking branch 'upstream/development' into development 2015-03-30 02:10:49 -05:00
Scott Lahteine
e96db1cd6c Make G29 shared function inline 2015-03-29 23:21:39 -07:00
Scott Lahteine
d73b169de3 Apply leveling for DELTA,
- Fix `prepare_move` function not calling `adjust_delta`
- Add more shorthand for plan_buffer_line.
- Fix wrong `federate` usage, assuming they are all mm/m
- Minor `stepper.cpp` cleanup
2015-03-29 23:16:12 -07:00
Scott Lahteine
ce44bee28b Small code reduction 2015-03-29 19:45:14 -07:00
Scott Lahteine
0213f7f016 Cleanup case for M666 2015-03-29 19:39:43 -07:00
Scott Lahteine
803425e12c Fix G29 E and M48 n
- Users prefer `G29 E` to work like `M48 E` so fixed that
- `M48 n` replaced with `M48 P` (or `p`). `n` legacy support
- Shorten some strings to save precious bytes
- Smaller code for 3-point probing
2015-03-29 18:56:09 -07:00
Scott Lahteine
e8ae51bfe3 Fix G28 homing Y with X
- Fixed a typo causing G28 to home incorrectly
- Added documentation to G28
- Added homeXYZ bools to neaten the code
- Added a note about home_offsets being questionable
2015-03-29 18:06:59 -07:00
Chris Roadfeldt
62834a1c43 Don't deploy probe on Z Axis homing if Z_PROBE_AND_ENDSTOP is enabled,
unless Z_SAFE_HOMING is.
2015-03-29 03:55:41 -05:00
Chris Roadfeldt
08a7aa16c5 Don't deploy Z Probe on Z homing if Z_PROBE_AND_ENDSTOP is defined. 2015-03-29 03:21:48 -05:00
Chris Roadfeldt
324c14943b Bug fixes for Z_PROBE_AND_ENDSTOP.
Code cleanup for Z_PROBE_AND_ENDSTOP.
Added Z_PROBE_PIN to pins_RAMPS_13.h
2015-03-29 02:16:09 -05:00
Scott Lahteine
afff968e88 ARRAY_BY_EXTRUDERS, shorthand to sync planner
- Add some documentation to planner and stepper headers
- Patch up RAMBO pins with undefs
- Add `sync_plan_position` inline to set current XYZE
- Swap indices in `extruder_offset` to fix initialization values
2015-03-28 20:33:21 -07:00
Scott Lahteine
2b0c25a091 Tweak G92 to call plan_set_position only once, yes? 2015-03-28 19:18:24 -07:00
Chris Roadfeldt
8b81f20c61 Filling in more places where Z_PROBE_PIN and Z_PROBE_AND_ENDSTOP need to
be.
Added Sanity Check for it.
Added hook so it's enabled.
2015-03-28 05:55:42 -05:00
Chris Roadfeldt
fd823449ad Added serial message for Z Probe trigger. 2015-03-28 05:42:38 -05:00
Scott Lahteine
b14be7235e Merge pull request #1585 from galexander1/strtod_e_fix
Fix `code_value` (so `G1X1E2` isn't evaluated as `G1 X100 E2`)
2015-03-27 20:49:03 -07:00
Scott Lahteine
ba871e46bf Fix compiler warnings
- Patched up for most included configurations
2015-03-27 20:29:05 -07:00
Scott Lahteine
ffe0df4b36 Latest upstream commits 2015-03-27 18:30:56 -07:00
Scott Lahteine
578f93bc26 Fixup temp arrays and leveling equation, prepare for merge 2015-03-27 16:20:23 -07:00
Scott Lahteine
460f73056b Fix ECHOPAIR ambiguity
- Also patch up some warnings
2015-03-27 00:46:39 -07:00
Scott Lahteine
19d418cd6a Fix up the code to eliminate warnings 2015-03-27 00:32:58 -07:00
Scott Lahteine
267d6bef15 Eliminate most warnings
- Fix a bug reading `code_value` for `M503 Sn`
- Hide and remove unused variables
2015-03-26 20:07:17 -07:00
Scott Lahteine
b76a352d41 Fix the planeNormal calculation 2015-03-26 17:14:07 -07:00
Scott Lahteine
0b32431551 Remove abs() from planeNormal.z 2015-03-26 16:20:23 -07:00
Scott Lahteine
06eb7f5b3c Latest upstream commits 2015-03-26 15:30:51 -07:00
Scott Lahteine
04328d7537 Add zprobe_zoffset in set_bed_level_equation_*
- Also a small tweak to SanityCheck.h
2015-03-26 15:29:16 -07:00
AnHardt
ebe5b87c2c < like in the oher compareble loops
to avoid:
Marlin_main.cpp:1790: warning: array subscript is above array bounds.
2015-03-26 21:18:19 +01:00
Scott Lahteine
fbf9b21e0c Merge plus fixup zprobe_zoffset
- Make `zprobe_zoffset` conditional
- Fix ConfigurationStore for `zprobe_zoffset`
2015-03-25 21:14:00 -07:00
Scott Lahteine
96b5da7198 Fix up bed leveling code
- Init `zprobe_zoffset`
- Remove `current_position[Z_AXIS] = zprobe_zoffset` lines from the
`set_bed_level_equation_*` functions
- Apply standards to `mesh_bed_leveling` files
- Document `MESH_BED_LEVELING`
2015-03-25 20:36:24 -07:00
Victor Torre
d43d47da14 Clean "fromsd" array is not SDSUPPORT
if not have SDSUPPORT the fromsd array is not necessary
2015-03-25 22:05:18 +01:00
alexborro
55025558dc Implement Dry-Run mode in G29
It just probe all the bed without appliying the matrix.
Useful after a first G29 to check the topology.
2015-03-25 11:12:30 -03:00
alexborro
c2ba5d0c09 Fix ZigZag and Topograph table
ZigZag: Inverted Behavior.. If T supplied, it does not zigzag.
Topograph table: The table was rotated 90º clockwise.
2015-03-24 15:50:31 -03:00
alexborro
0ce3576685 New Feature: Z_DUAL_ENDSTOPS
Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z
steppers - Let's call them Z stepper and Z2 stepper.
That way the machine is capable to align the bed during home, since both
Z steppers are homed.
There is also an implementation of M666 (software endstops adjustment)
to this feature.
After Z homing, this adjustment is applied to just one of the steppers
in order to align the bed.
One just need to home the Z axis and measure the distance difference
between both Z axis and apply the math: Z adjust = Z - Z2.
If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it
is.. think about it) and the Z adjust would be positive.
Play a little bit with small adjustments (0.5mm) and check the
behaviour.
The M119 (endstops report) will start reporting the Z2 Endstop as well.
2015-03-24 14:06:44 -03:00
Scott Lahteine
0d81abe1c9 Merge branch 'Development' into config_testing
Latest upstream commits
2015-03-23 21:13:04 -07:00
Scott Lahteine
b26a3ea02c Merge pull request #1662 from josla972/refactor_scara
Refactor SCARA calibration. Save some lines of code and possibly ROM.
2015-03-23 00:51:18 -07:00
Scott Lahteine
4fbb80567e Get upstream commits 2015-03-22 23:07:22 -07:00
Scott Lahteine
146501215f Fix mangled probe_pt calls
- Address issue #1669
- Remove the TOPO_ORIGIN configuration setting
2015-03-22 21:45:20 -07:00
maverikou
15345cc249 Corrected Z_PROBE_ALLEN_KEY behaviour. 2015-03-22 13:54:51 +02:00
maverikou
0f034dd97e Clean up Z_RAISE_AFTER_PROBING to work the same in all code paths except Z_PROBE_SLED. 2015-03-22 13:54:45 +02:00
maverikou
6c96f32069 Blind fix for #1507 2015-03-22 13:54:21 +02:00
Josef Larsson
379348487e Removed malplaced comment. 2015-03-22 12:21:31 +01:00
Josef Larsson
9b3462f73f Refactor SCARA calibration. Save some lines of code and possibly ROM. 2015-03-22 00:37:24 +01:00
Scott Lahteine
691e753cc3 Don't add home offsets in G29
- Address #1262 by leaving values as set
- Rename `add_homing` to `home_offset`
2015-03-21 16:30:02 -07:00
Scott Lahteine
15eb5d35a2 Merge branch 'Development' into config_testing
Latest upstream commits
2015-03-21 15:42:45 -07:00
Edward Patel
3d0a060a7a Added G29 command 2015-03-21 14:50:47 +01:00
Scott Lahteine
63d5d28085 Merge branch 'Development' into config_testing
Latest upstream changes
2015-03-20 04:15:18 -07:00
Edward Patel
4619d80524 Merge branch 'Development' into manual-bed-leveling+mesh-bed-level 2015-03-20 11:45:06 +01:00
Scott Lahteine
2424713a8f Merge pull request #1640 from AnHardt/warning6
codepos not used in gcode_M28()
2015-03-20 02:58:00 -07:00
Scott Lahteine
670006b919 Remove invariant code from Configurations
- Add `Conditionals.h` with calculated configuration values
- Add `SanityCheck.h` with checks for configuration errors
- Remove equivalent code from all configurations
- Move error checks from some sources to `SanityCheck.h` also
- Fix initialization of count_direction in stepper.cpp
2015-03-19 22:22:23 -07:00
Edward Patel
a61f679568 Merge branch 'Development' into manual-bed-leveling+mesh-bed-level 2015-03-20 02:28:35 +01:00
Edward Patel
c87faa69ed Shortened mesh_plan_buffer_line() 2015-03-20 02:18:49 +01:00
AnHardt
ae01a6b5f2 Make use of codepos.
Saves one addition.
Needs one pointer on the stack.

Don't know if this is a go trade.
2015-03-19 09:45:16 +01:00
Scott Lahteine
80e0ee10ca Merge pull request #1631 from AnHardt/iss1593
Decrease KILL_DELAY
2015-03-18 19:10:38 -07:00
Scott Lahteine
76127b8a55 Merge pull request #1630 from Wurstnase/fix_g29
optional parameters must be named when ignoring order
2015-03-18 19:09:40 -07:00
Scott Lahteine
8664c6d465 Merge pull request #1638 from AnHardt/warning4
delta[3] not used when DELTA not defined.
2015-03-18 19:07:55 -07:00
Scott Lahteine
10711ccc6a Merge pull request #1639 from AnHardt/warning5
G4 could wait for an undefined time
2015-03-18 19:07:14 -07:00
Edward Patel
240b5cfe04 Merge branch 'Development' into manual-bed-leveling+mesh-bed-level 2015-03-18 19:19:46 +01:00
alexborro
4521f6655b Restore "S" parameter of M204 for retrocompatibility. 2015-03-18 12:19:30 -03:00
alexborro
5ddb8d94e2 Update Documentation related to M204 2015-03-18 11:09:10 -03:00
AnHardt
f8c4d43886 delta[3] is used with SCARA
Shoot in the dark.
2015-03-18 12:14:49 +01:00
AnHardt
72a9fed4fb codepos not used in gcode_M28()
Got:
Marlin_main.cpp:2567: warning: unused variable 'codepos'

Needs revision.
Don't now how this should look like.
2015-03-18 11:41:14 +01:00
AnHardt
b94dd33641 G4 could wait for an undefined time
Got:
Marlin_main.cpp:1689: warning: 'codenum' may be used uninitialized in this function

And indeed codenum is undefined when no parameter is given.
2015-03-18 11:23:41 +01:00
AnHardt
e90985a4e8 delta[3] not used when DELTA not defined.
got:
Marlin_main.cpp:387: warning: 'delta' defined but not used

Compiles cleaner when definition is removed.
2015-03-18 11:11:49 +01:00
AnHardt
d1658eebfc Decrease KILL_DELAY
Users hat to press kill-button for unexpexted lon times.
See #1593
2015-03-18 01:45:42 +01:00
Wurstnase
00adb2a6c1 optional parameters must be named when ignoring order 2015-03-18 01:02:29 +01:00
Edward Patel
0d43898a22 Remove of mesh_plan_buffer_line parameter reference (e) 2015-03-17 22:55:29 +01:00
Edward Patel
8067a985ce Merge branch 'Development' into manual-bed-leveling+mesh-bed-level
Fixed conflicts:
	Marlin/planner.h
2015-03-17 22:48:08 +01:00
maverikou
3570447ded Fix Z_RAISE_AFTER_PROBING 2015-03-16 08:35:49 +02:00
maverikou
8a739b6fba Merge branch 'Development' into delta_auto_bed_level
Conflicts:
	Marlin/Marlin_main.cpp
2015-03-16 08:24:26 +02:00
Scott Lahteine
a686c9878f Move TOPO_ORIGIN define to Configuration.h
- Addressing issue #1608
2015-03-15 15:49:36 -07:00